Sun Blade 1000, can't boot from Solaris 10 from DVD/CDROM nor from disk

jkadm

Can't boot from Solaris 10 from DVD/CDROM nor from disk,  and system maintenance not working.  


screen output as follows.


Rebooting with command: boot cdrom
Boot device: /pci@8,700000/scsi@6/disk@6,0:f  File and args:
Evaluating: boot cdrom

Can't open boot device

Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w2100002037bdf264,0:a  File an
d args:
SunOS Release 5.10 Version Generic_127127-11 64-bit
Copyright 1983-2008 Sun Microsystems, Inc.  All rights reserved.
Use is subject to license terms.
Hostname: myb1000
SUNW,eri0 : 100 Mbps full duplex link up

ERROR: svc:/system/filesystem/root:default failed to mount /usr  (see 'svcs -x'
for details)
Requesting System Maintenance Mode
(See /lib/svc/share/README for more information.)
Console login service(s) cannot run

Root password for system maintenance (control-d to bypass):
single-user privilege assigned to /dev/console.
Entering System Maintenance Mode

Oct 27 04:13:55 su: 'su root' succeeded for root on /dev/console
-sh: /bin/i386: not found
-sh: /usr/sbin/quota: not found
-sh: /bin/cat: not found
-sh: /bin/mail: not found
# ls
ls: not found
# mount
mount: not found
# svcs -x
svcs: not found
#


Note:

System with Toshiba DVD/CDROM  SD-M1401, applied patch  111649-04.
iostat -E | grep DVD  shows
vendor: toshiba product: dvd-rom sd-m1401 revision: 1009 serial no:


Anyone has any suggestion?

[ 本帖最后由 jkadm 于 2009-10-30 01:45 编辑 ]

jkadm

thanks for any help!

[ 本帖最后由 jkadm 于 2009-10-30 01:44 编辑 ]

easybegin

光驱坏了或者光盘

zhmzhouming

try another DVD first, it most likely to be a media failure caused.
if no effect, contact SUN 800 for DVD-ROM replacing .

jkadm

Thank you all for the response!

The DVD/CD is no issue, I tried with another one  and got the same error.  I had Solaris 10 11/06 before and tried to upgrade to 05/09.  The DVD worked with first run but quit in half way.  When I tried the second time I got the can't open boot device error, and again with another same model DVD.  I wonder if some can give me a physical path of the boot file on the DVD so that I can set up the alias at OBP.

I remember during the installation, it prompted me the eeprom change for boot slice and I set it to c1t1d0s0.  I wonder if this changed the default  boot device/file path?  It has been very long time since  the last  OBP config change, I just could not remember the proper way of manually config boot device/file  in OBP.

Also, if put DVD aside, how should I proceed with the system maintenance mode when it head to these message:
-sh: /bin/i386: not found
-sh: /usr/sbin/quota: not found
-sh: /bin/cat: not found
-sh: /bin/mail: not found
# ls
ls: not found
# mount
mount: not found
# svcs -x
svcs: not found
#

jkadm

no one got more ideas?  There must be more than one way to solve the problem, .  I will be back!

easybegin

全英文啊