免费注册 查看新帖 |

Chinaunix

  平台 论坛 博客 文库
最近访问板块 发新帖
查看: 5193 | 回复: 2

cisco3524的管理vlan配置需注意那些??那位能提供有关cisco3524 [复制链接]

论坛徽章:
0
发表于 2002-12-15 16:16 |显示全部楼层

论坛徽章:
0
发表于 2002-12-16 09:09 |显示全部楼层

cisco3524的管理vlan配置需注意那些??那位能提供有关cisco3524

参考:
Cisco 3548(3524) 交换机:

第一次连接交换机,配置终端参数为:
  波特率:9600;数据位:8;停止位:1;奇偶校验:无;流控制:无。
通过串口线连上路由器后,按回车,即可看到配置向导:
(如果不是第一次配置,可以进入超级用户模式后用命令setup调用以下过程)

         --- System Configuration Dialog ---

At any point you may enter a question mark '?' for help.任何时候可以打?取得帮助
Use ctrl-c to abort configuration dialog at any prompt.按Ctrl-C可以取消并退出
Default settings are in square brackets '[]'.默认参数在[]中

Continue with configuration dialog? [yes/no]: y继续交互配置吗?回答:y
Enter IP address: 10.1.1.249ip地址
Enter IP netmask: 255.255.255.0子网掩码
Would you like to enter a default gateway address? [yes]: y设置默认网关?y
IP address of default gateway: 10.1.1.254默认网关
Enter host name [3548_9A]:

The enable secret is a one-way cryptographic secret used
instead of the enable password when it exists.

Enter enable secret: _password输入超级用户密码

Would you like to configure a Telnet password? [yes]: y
Enter Telnet password: _password输入telnet密码
Would you like to enable as a cluster command switch? [yes/no]: n集群模式?n

The following configuration command script was created:已建立以下配置信息

ip subnet-zero
interface VLAN1
ip address 10.1.1.249 255.255.255.0
ip default-gateway 10.1.1.254
enable secret 5 $1$biZ3$AOLb9cMTtBwMtGB9lyBzr.
line vty 0 15
password _domainwlzx
snmp community private rw
snmp community public ro
!
end

Use this configuration? [yes/no]:使用该配置信息吗? y

修改配置:

禁止通过snmp管理:
3548>;enable
password:
        3548#config term
3548(config)#no snmp community private
3548(config)#no snmp community public

接着配置干道:(确定上级交换机对应端口已设为干道模式)
3548(config)#inter g0/1 选择第一个千兆口
3548(config if)# switchport mode trunk设为干道模式
    如果g0/2用于连接另一台3548,也设为干道
3548(config)#inter g0/2
3548(config if)# switchport mode trunk
    返回
3548(config if)# exit
3548(config)# exit
3548#
验证: ping 10.1.1.254

配置Vlan数据:
3548#vlan database
3548(vlan)#reset清除以前的配置
3548(vlan)#vtp client设为vtp客户模式
3548(vlan)#vtp domain _domainvtp域是_domain
3548(vlan)#vtp password ********设定vtp域密码
3548(vlan)#exit
3548#
验证:show vtp status显示vlan 数据
show vtp counters
show vlan
    同步后看到的vlan数目和名称应与6506上的一致

指定端口到Vlan、配置端口为portfast方式(快速建立连接):
方法1:命令方式
3548#config term
3548(config)#inter f0/1配置1号快速以太网端口
3548(config if)# switchport access vlan 2指定端口到Vlan 2
3548(config if)# spanning-tree portfast配置端口为portfast方式
3548(config)#inter f0/2配置1号快速以太网端口
3548(config if)# switchport access vlan 2指定端口到Vlan 2
3548(config if)# spanning-tree portfast配置端口为portfast方式
...对每个要设定的端口重复上述步骤。
3548(config if)# exit
3548(config)# exit
3548#
方法1:Web 方式
(预先要安装插件:jre-1-2-2-005-win-i-09-mar-2000.exe)
打开浏览器连接设备:在地址栏输入设备的管理页面url,如3548_9a(10.1.1.24为:http://10.1.1.249/basiccfg.html
选中菜单port ->; port configure ->; 设port fast 为Enable
选中菜单vlan ->; vlan membership ->; 指定端口所属的Vlan号 可同时指定多个端口




! 注意: 如果把一个端口指定到不存在的VLAN上,3548交换机的VLAN同步会异常,此时应该为正确VLAN并重新“配置Vlan数据”

保存配置信息:
方法1:命令方式
3548# write ( 或 copy running-config startup-config )
方法1:Web 方式
选中设备(而不是单个端口),点击save configure按钮。


3548_9A#show run
Building configuration...

Current configuration:
!
version 12.0#软件版本
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname 3548_9A#系统名称
!
enable secret 5 $1$4ZMs$rfC.g/nN.owt3eW2uoCL/0#加密后的enable密码
!
!
!
!
!
!
ip subnet-zero
!
!
!
interface FastEthernet0/1#模块0的1号快速以太网接口
switchport access vlan 5#指定端口0/1到vlan 5
spanning-tree portfast#如果接的是工作站,指定端口为portfast方式(不运行生成树协议,加快建立连接速度)
!
interface FastEthernet0/2
spanning-tree portfast#默认情况下端口属vlan 1
!
interface FastEthernet0/3
spanning-tree portfast
!
interface FastEthernet0/4
spanning-tree portfast
!
interface FastEthernet0/5
spanning-tree portfast
!
interface FastEthernet0/6
spanning-tree portfast
!
interface FastEthernet0/7
spanning-tree portfast
!
interface FastEthernet0/8
spanning-tree portfast
!
interface FastEthernet0/9
spanning-tree portfast
!
interface FastEthernet0/10
spanning-tree portfast
!
interface FastEthernet0/11
spanning-tree portfast
!
interface FastEthernet0/12
spanning-tree portfast
!
interface FastEthernet0/13
spanning-tree portfast
!
interface FastEthernet0/14
spanning-tree portfast
!
interface FastEthernet0/15
spanning-tree portfast
!
interface FastEthernet0/16
spanning-tree portfast
!
interface FastEthernet0/17
spanning-tree portfast
!
interface FastEthernet0/18
spanning-tree portfast
!
interface FastEthernet0/19
spanning-tree portfast
!
interface FastEthernet0/20
spanning-tree portfast
!
interface FastEthernet0/21
spanning-tree portfast
!
interface FastEthernet0/22
spanning-tree portfast
!
interface FastEthernet0/23
spanning-tree portfast
!
interface FastEthernet0/24
spanning-tree portfast
!
interface FastEthernet0/25
spanning-tree portfast
!
interface FastEthernet0/26
spanning-tree portfast
!
interface FastEthernet0/27
spanning-tree portfast
!
interface FastEthernet0/28
spanning-tree portfast
!
interface FastEthernet0/29
spanning-tree portfast
!
interface FastEthernet0/30
spanning-tree portfast
!
interface FastEthernet0/31
spanning-tree portfast
!
interface FastEthernet0/32
spanning-tree portfast
!
interface FastEthernet0/33
spanning-tree portfast
!
interface FastEthernet0/34
spanning-tree portfast
!
interface FastEthernet0/35
spanning-tree portfast
!
interface FastEthernet0/36
spanning-tree portfast
!
interface FastEthernet0/37
spanning-tree portfast
!
interface FastEthernet0/38
spanning-tree portfast
!
interface FastEthernet0/39
spanning-tree portfast
!
interface FastEthernet0/40
spanning-tree portfast
!
interface FastEthernet0/41
spanning-tree portfast
!
interface FastEthernet0/42
spanning-tree portfast
!
interface FastEthernet0/43
spanning-tree portfast
!
interface FastEthernet0/44
spanning-tree portfast
!
interface FastEthernet0/45
spanning-tree portfast
!
interface FastEthernet0/46
spanning-tree portfast
!
interface FastEthernet0/47
spanning-tree portfast
!
interface FastEthernet0/48
spanning-tree portfast
!
interface GigabitEthernet0/1
switchport mode trunk#设置G0/1为运行isl协议的干道,默认允许所有vlan通过
!
interface GigabitEthernet0/2
!
interface VLAN1
ip address 10.1.1.249 255.255.255.0#本交换机的IP地址
no ip directed-broadcast
no ip route-cache
!
ip default-gateway 10.1.1.254#默认网关
snmp-server engineID local 00000009020000036BC
!
line con 0
transport input none
stopbits 1
line vty 0 4
password _password#telnet密码
login
line vty 5 15
password _password#telnet密码
login
!
end

论坛徽章:
0
发表于 2002-12-16 14:04 |显示全部楼层

cisco3524的管理vlan配置需注意那些??那位能提供有关cisco3524

谢谢
您需要登录后才可以回帖 登录 | 注册

本版积分规则 发表回复

  

北京盛拓优讯信息技术有限公司. 版权所有 京ICP备16024965号-6 北京市公安局海淀分局网监中心备案编号:11010802020122 niuxiaotong@pcpop.com 17352615567
未成年举报专区
中国互联网协会会员  联系我们:huangweiwei@itpub.net
感谢所有关心和支持过ChinaUnix的朋友们 转载本站内容请注明原作者名及出处

清除 Cookies - ChinaUnix - Archiver - WAP - TOP