Sun M9000 XSCF 配置

Jackychen83

M9000 XSCF 配置：
1、串口登录
插入钥匙到M9000系统的系统面板，打到“扳手”的位置 ，用串口线连接XSCF串口
login: default
Change the panel mode switch to Locked and press return... 将钥匙打到 “锁”位置，按回车。
Leave it in that position for at least 5 seconds.  Change the panel mode switch to Service, and press return...等待5秒钟后，再将钥匙打到“扳手”的位置，按回车 。
XSCF>

2、用setupplatform配置XSCF的网络接口、服务等：
XSCF>
XSCF> setupplatform（设置控制器平台）
Do you want to set up an account? [y|n]: n
Do you want to set up networking? [y|n]: y
Do you want to set up the XSCF network interfaces? [y|n]: y （选择是否设置xscf的网口）
Do you want to configure xscf#0-lan#0? [y|n]: y
xscf#0-lan#0 ip address? []: 10.66.4.1（ip地址）
xscf#0-lan#0 netmask? [255.255.255.0]: 255.255.254.0（子网掩码）
xscf#0-lan#0 default gateway? []: 10.66.5.253（网关）
     xscf#0-lan#0 ip address: 10.66.4.1
     xscf#0-lan#0 netmask: 255.255.254.0
     xscf#0-lan#0 default gateway: 10.66.5.253
Are these settings correct? [y|n]: y
XSCF> setnetwork xscf#0-lan#0 -m 255.255.254.0 10.66.4.1
XSCF> setroute -c add -n 0.0.0.0 -m 0.0.0.0 -g 10.66.5.253 xscf#0-lan#0
Do you want to configure xscf#0-lan#1? [y|n]: n
Do you want to configure lan#0? [y|n]: y
lan#0 ip address? []: 10.66.4.3
lan#0 netmask? [255.255.255.0]: 255.255.254.0
     lan#0 ip address: 10.66.4.3
     lan#0 netmask: 255.255.254.0
Are these settings correct? [y|n]: y
XSCF> setnetwork lan#0 -m 255.255.254.0 10.66.4.3
Do you want to configure lan#1? [y|n]: n
Do you want to configure xscf#1-lan#0? [y|n]: y
xscf#1-lan#0 ip address? []: 10.66.4.2
xscf#1-lan#0 netmask? [255.255.255.0]: 255.255.254.0
xscf#1-lan#0 default gateway? []: 10.66.5.253
     xscf#1-lan#0 ip address: 10.66.4.2
     xscf#1-lan#0 netmask: 255.255.254.0
     xscf#1-lan#0 default gateway: 10.66.5.253
Are these settings correct? [y|n]: y
XSCF> setnetwork xscf#1-lan#0 -m 255.255.254.0 10.66.4.2
XSCF> setroute -c add -n 0.0.0.0 -m 0.0.0.0 -g 10.66.5.253 xscf#1-lan#0
Do you want to configure xscf#1-lan#1? [y|n]: n
xscf#0-if is already configured:
     xscf#0-if ip address: 192.168.1.1
     xscf#0-if netmask: 255.255.255.0
Do you want to configure xscf#0-if? [y|n]: y
xscf#0-if ip address? [192.168.1.1]:
xscf#0-if netmask? [255.255.255.0]:
     xscf#0-if ip address: 192.168.1.1
     xscf#0-if netmask: 255.255.255.0
Are these settings correct? [y|n]: y
XSCF> setnetwork xscf#0-if -m 255.255.255.0 192.168.1.1
Do you want to configure xscf#1-if? [y|n]: y
xscf#1-if ip address? []: 192.168.1.2
xscf#1-if netmask? [255.255.255.0]:
     xscf#1-if ip address: 192.168.1.2
     xscf#1-if netmask: 255.255.255.0
Are these settings correct? [y|n]: y
XSCF> setnetwork xscf#1-if -m 255.255.255.0 192.168.1.2
DSCP network is already configured:
     DSCP network: 192.168.224.0
     DSCP netmask: 255.255.255.0
Do you want to set up the DSCP network? [y|n]: y
DSCP network? [192.168.224.0]:
DSCP netmask? [255.255.255.0]:
     DSCP network: 192.168.224.0
     DSCP netmask: 255.255.255.0
Are these settings correct? [y|n]: y
XSCF> setdscp -q -y -i 192.168.224.0 -m 255.255.255.0
Domain name service is already configured:
     Primary DNS server ip address:
     Secondary DNS server ip address:
     Tertiary DNS server ip address:
     Domain name: localdomain
     XSCF#0 hostname: localhost
     XSCF#1 hostname: localhost
Do you want to set up the domain name service? [y|n]: y
Primary DNS server ip address? []: 10.66.4.6
Do you want a secondary DNS server? [y|n]: n
Do you want to specify a domain name? [y|n]: y         
Domain name [localdomain]: shengli.com
XSCF#0 hostname [localhost]: M91-XSCF0
XSCF#1 hostname [localhost]: M91-XSCF1
     Primary DNS server ip address: 10.66.4.6
     Secondary DNS server ip address:
     Tertiary DNS server ip address:
     Domain name: shengli.com
     XSCF#0 hostname: M91-XSCF0
     XSCF#1 hostname: M91-XSCF1
Are these settings correct? [y|n]: y
XSCF> setnameserver -c del -a
XSCF> setnameserver -c add 10.66.4.6
XSCF> sethostname xscf#0 M91-XSCF0
XSCF> sethostname xscf#1 M91-XSCF1
XSCF> sethostname -d shengli.com
Do you want to set up the network time protocol? [y|n]: n
The ssh service is:  disabled
Do you want to set up ssh? [y|n]: n
The https service is:  disabled
Do you want to set up https? [y|n]: n
Do you want to configure email reports? [y|n]: n
Do you want to apply the network changes? [y|n]: y
XSCF> applynetwork -y
The following network settings will be applied:
  xscf#0 hostname  :M91-XSCF0
  xscf#1 hostname  :M91-XSCF1
  DNS domain name  :shengli.com
  nameserver       :10.66.4.6

  interface        :xscf#0-lan#0
  status           :up
  IP address       :10.66.4.1
  netmask          :255.255.254.0
  route            :-n 0.0.0.0 -m 0.0.0.0 -g 10.66.5.253

  interface        :xscf#0-lan#1
  status           :up
  IP address       :192.168.0.1
  netmask          :255.255.255.0
  route            :-n 0.0.0.0 -m 0.0.0.0 -g 10.66.5.253

  interface        :xscf#0-if
  status           :up
  IP address       :192.168.1.1
  netmask          :255.255.255.0

  interface        :lan#0
  status           :up
  IP address       :10.66.4.3
  netmask          :255.255.254.0

  interface        :xscf#1-lan#0
  status           :up
  IP address       :10.66.4.2
  netmask          :255.255.254.0
  route            :-n 0.0.0.0 -m 0.0.0.0 -g 10.66.5.253

  interface        :xscf#1-lan#1
  status           :down
  IP address       :
  netmask          :
  route            :

  interface        :xscf#1-if
  status           :up
  IP address       :192.168.1.2
  netmask          :255.255.255.0

  interface        :lan#1
  status           :down
  IP address       :
  netmask          :

Continue? [y|n] :y
Please reset the XSCF by rebootxscf to apply the network settings.
Please confirm that the settings have been applied by executing
showhostname, shownetwork, showroute and shownameserver after rebooting
the XSCF.
Do you want to reboot the XSCF now? [y|n]: y
XSCF> rebootxscf -q -y
Do you want to set up the chassis altitude? [y|n]: execute K000end  --  
complete
execute S10ioxoff  --  complete


Chassis altitude is already configured:
     Chassis altitude in meters:
Continue setting up the chassis altitude? [y|n]: n


本文来自ChinaUnix博客，如果查看原文请点：http://blog.chinaunix.net/u/23363/showart_2149262.html