rx7620无法加电，麻烦熟悉7620的哥们看一眼

easybegin

[mp] MP:CM> ps

Display detailed status of the selected MP bus device.


The following MP bus devices were found:
+---+----+----+-----+-----+-------+-----+
|   |    |    |     |     |       |     |
|   |    |LAN\| Sys |     |  IO   |     |
|Cab| MP |SCSI|Bkpln|Cells|Chassis| BPS |
| # |M  S|0  1|     | 0 1 | 0   1 | 0 1 |
+---+----+----+-----+-----+-------+-----+
| 0 |*  *|*  *|  *  | *   | *   * | * * |
+---+----+----+-----+-----+-------+-----+

You may display detailed power and hardware status for the following items:

    T - Cabinet
    S - System Backplane
    G - MP (Core I/O)
    P - IO Chassis
    C - Cell
        Select Device: s

HW status for System Backplane : No Fault Found

Global Power Monitor version 1.002 is OK
System Fan Monitor version 1.002 is OK
Local Power Monitor version is 2.000
Hotswap controller version is 1.000

Backplane power is on, no fault

VRM's           0 1 2 3 4 5
Present      :     * * * *
OK           :     * * * *
Enabled      :     * * * *

Master Clock Frequency is 130 MHz
Fabric Clock Frequency is 500 MHz

easybegin

[mp] MP:CM> ps

Display detailed status of the selected MP bus device.


The following MP bus devices were found:
+---+----+----+-----+-----+-------+-----+
|   |    |    |     |     |       |     |
|   |    |LAN\| Sys |     |  IO   |     |
|Cab| MP |SCSI|Bkpln|Cells|Chassis| BPS |
| # |M  S|0  1|     | 0 1 | 0   1 | 0 1 |
+---+----+----+-----+-----+-------+-----+
| 0 |*  *|*  *|  *  | *   | *   * | * * |
+---+----+----+-----+-----+-------+-----+

You may display detailed power and hardware status for the following items:

    T - Cabinet
    S - System Backplane
    G - MP (Core I/O)
    P - IO Chassis
    C - Cell
        Select Device: g

HW status for MP : No Fault Detected

Complex model string: 9000/800/rx7620

Attention LED is ON
Remote LED is OFF

Battery state is good

Last MP software reset occurred WED JAN 14 08:33:36 1987

MP firmware rev 7.002, built on Jun 24 2005 10:53:32

[mp] MP:CM>

easybegin

[mp] MP:CM> ps

Display detailed status of the selected MP bus device.


The following MP bus devices were found:
+---+----+----+-----+-----+-------+-----+
|   |    |    |     |     |       |     |
|   |    |LAN\| Sys |     |  IO   |     |
|Cab| MP |SCSI|Bkpln|Cells|Chassis| BPS |
| # |M  S|0  1|     | 0 1 | 0   1 | 0 1 |
+---+----+----+-----+-----+-------+-----+
| 0 |*  *|*  *|  *  | *   | *   * | * * |
+---+----+----+-----+-----+-------+-----+

You may display detailed power and hardware status for the following items:

    T - Cabinet
    S - System Backplane
    G - MP (Core I/O)
    P - IO Chassis
    C - Cell
        Select Device: g

HW status for MP : No Fault Detected

Complex model string: 9000/800/rx7620

Attention LED is ON
Remote LED is OFF

Battery state is good

Last MP software reset occurred WED JAN 14 08:33:36 1987

MP firmware rev 7.002, built on Jun 24 2005 10:53:32

easybegin

[mp] MP:CM> ps

Display detailed status of the selected MP bus device.


The following MP bus devices were found:
+---+----+----+-----+-----+-------+-----+
|   |    |    |     |     |       |     |
|   |    |LAN\| Sys |     |  IO   |     |
|Cab| MP |SCSI|Bkpln|Cells|Chassis| BPS |
| # |M  S|0  1|     | 0 1 | 0   1 | 0 1 |
+---+----+----+-----+-----+-------+-----+
| 0 |*  *|*  *|  *  | *   | *   * | * * |
+---+----+----+-----+-----+-------+-----+

You may display detailed power and hardware status for the following items:

    T - Cabinet
    S - System Backplane
    G - MP (Core I/O)
    P - IO Chassis
    C - Cell
        Select Device: c
    Enter cell number: 0

HW status for Cell 0 : FAILURE DETECTED

Power status : OFF, no fault
Boot is blocked
PDH memory is not shared
Processor Compatibility : OK
RIO cable status : connected
RIO cable connection physical location : PCI Domain 0
Core cell is INVALID
Attention Led is off

PDHC status Leds :  --*-

CPU Module Slot    0 1 2 3
Populated         P   P  
Local 48V Good    *   *  
Power Enabled            
Power Good               

   (* - True, P - Processor, T - Terminator)



DIMMs populated:
0 . . . 4 . . . 8 . . .12 . . .
                                

                                  1 1 1 1 1 1
VRM's           1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present      : * * * * * * * * * * * * * * *
Enabled      :       * *   *               *
Pwr Good     :       * *   *               *


Front Side Bus Freq.    : 200 MHz
CPU Core Freq.          : 1600 MHz
CPU Part Number         : 80543KC

System Boot Rom (SFW) firmware rev   1.025
PDH controller (PDHC) firmware rev 3.023, built WED FEB 16 14:33:12 2005
MICE revision is 1.0

[mp] MP:CM>

easybegin

换了个cell板在0号位，现在可以起到EFI，不过信息和上面一样，是不是风扇有问题？

leelangco

啥信息和上面一样？
既然可以启到EFI，下一步就可以引导系统了啊

easybegin

啥信息？
既然可以启到EFI，下一步就可以引导系统了啊
leelangco 发表于 2010-08-26 20:09

    EFI Boot Manager ver 1.10 [14.61]

Please select a boot option

    Boot option maintenance menu                                    


    Use ^ and v to change option(s). Use Enter to select an option

easybegin

然后我添加引导信息


EFI Boot Maintenance Manager ver 1.10 [14.61]

Select file or change to new directory:

       [Treat like Removable Media Boot]                           
    Exit                                                            
                                                  

说IA64_EFI [Acpi(HWP0002,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig4可能是Treat like Removable Media Boot光驱。我起名dvd

easybegin

EFI Boot Manager ver 1.10 [14.61]

Please select a boot option

    DVD                                                            
    Boot option maintenance menu                                    


    Use ^ and v to change option(s). Use Enter to select an option
Loading.: DVD                                                      
Load of DVD failed: Not Found
Paused - press any key to continue

easybegin

光驱是AB351-62001，是DVD，我换了光盘，还是不能引导