- 论坛徽章:
- 0
|
Severity: Normal -- informational in nature. A physical disk drive has reported a check condition error. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerp_id field. The HSV100 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the al_pa field. The location of the physical disk drive is determined by the content of the dencl_num field as follows:
<UL>
<LI>If dencl_num is less than 99, the location is as indicated by the content of the rack_num, dencl_num, and bay fields.
<LI>If dencl_num is equal to 99, the location is unknown. Note that the content of the rack_num and bay fields is undefined in this case.
<LI>If dencl_num is greater than 99, the HSV100 controller does not have proof of the current location but the last known location is indicated by the content of the rack_num, dencl_num, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values.
</UL>Note that the content of the rack_num field will not be valid until a future release. The Fibre Channel Exchange Descriptor class is contained in the fed_class field. The command issued to the physical disk drive is contained in the cmd field. The sense data obtained from the physical disk drive as a result of the check condition error is contained in the error field. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerp_id field. The location of an available drive enclosure is determined by the content of the enclosures.dencl_num field as follows:
<UL>
<LI>If enclosures.dencl_num is less than 99, the location is as indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields.
<LI>If enclosures.dencl_num is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rack_num field is undefined in this case.
<LI>If enclosures.dencl_num is greater than 99, the HSV100 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate.
</UL>Note that the content of the enclosures.rack_num field will not be valid until a future release.
A physical disk drive has reported a
check condition error.
Physical disk drive:
2002-000c-ca23-9b59-0000-0000-0000-0000
; Port ID: DP-1B; Rack number not valid
in this release; Enclosure: 1.; Bay:
11.; AL_PA: 0x002a; exch_type: 3
(Data-path with SEST extended SGL);
opcode: 0x2f (*VERIFY (10 byte)*);
Sense Key: 1 (*RECOVERED ERROR*); ASC:
0x18 ASCQ: 0x00 (*Recovered data with
error correction applied*); FRU Code:
0x09; LBA: 0x06f69000; Info:
0x06f69202; Drive enclosures available
on port DP-1B may be found in the
enclosures array in this event's
detailed information
EIP09 - Fibre Channel Services Physical Disk Drive/Mirror Port Error
An error was encountered while attempting to access a physical disk drive or the mirror port.
Event Log Packet Event Specific Information
flags (Flags)
Flag field bits: 01000011
Time has been set on this HSV100 controller: TRUE
Time has been synchronized with all HSV100 controllers in the Storage System: TRUE
Event sequence number reset occurred: FALSE
Event reported out of sequence due to Final Event Block reconciliation or lost host event: FALSE
Event requeued following restart or resynchronization: FALSE
Event reported using LAB code: FALSE
Event reported by primary HSV100 controller (Note: Not valid until Storage System primary HSV100 controller is elected): TRUE
Single power supply HSV100 controller: FALSE
revision - Structure revision number: 2 [0x02]
count - Event specific information size in bytes: 168 [0xa8]
sequence_number - Sequence number assigned to the event: 5621 [0x15f5]
sw_version - HSV100 controller software version number string: 3028
baselevel_id - HSV100 controller baselevel build string: CR0A3E
ctrlr_model_id - HSV100 controller model string: HSV100
reporting_ctrlr - Storage System Management Interface Handle of HSV100 controller that reported the event: Noid: 0 IdType: 7 IdLength: 8 UUID: 5005-08b4-0010-2f46-0000-0000-0000-0000
report_time - Time event was reported: Date: 6-Sep-2010 Time: 07:45:29:543
report_location - Location of event report call: 1366616 [0x14da58]
header (Header Information)
** NOTE: The following is part of a UNION with more than one interpretation.
You will need to determine which union value is relevant.
** START UNION: ( u - Event Code Union ) **
ec (Event Code)
eiptype - Event Information Packet Type Code: 9 [0x09]
cac - Corrective Action Code: 0 [0x00]
Corrective Action: No action necessary.
evnum - Event Number: 2 [0x02]
scid - HSV100 Controller Software Component Identification: 6 [0x06]
** UNION OR: ( u - Event Code Union ) **
value - Event Code Value: 100794377 [0x06020009]
** END UNION: ( u - Event Code Union ) **
revision - Packet revision number: 3 [0x03]
type - Packet type: 9 [0x09]
count - Number of bytes in packet: 104 [0x68]
device - UUID of physical disk drive associated with the event: 2002-000c-ca23-9b59-0000-0000-0000-0000
cerp_id - HSV100 controller enclosure rear panel Fibre Channel port attached to the physical disk drive or mirror port: DP-1B
exch_type - Frame exchange type: 3 [0x03]
port - HSV100 controller internal Fibre Channel port number attached to the physical disk drive or mirror port: 3 [0x03]
dencl_num - Enclosure where the physical disk drive is located: 1 [0x01]
al_pa - AL_PA of the physical disk drive or mirror port: 42 [0x2a]
rack_num - Rack where physical disk drive is located: 0 [0x00]
bay - Enclosure bay where the physical disk drive is located: 11 [0x0b]
fed_class - Fibre Channel Exchange Descriptor class: 48 [0x30]
** NOTE: The following is part of a UNION with more than one interpretation.
You will need to determine which union value is relevant.
** START UNION: ( cmd - Command Descriptor Block issued ) **
bytes - CDB as bytes:
[ 0]: 47 [0x2f]
[ 1]: 0 [0x00]
[ 2]: 6 [0x06]
[ 3]: 246 [0xf6]
[ 4]: 144 [0x90]
[ 5]: 0 [0x00]
[ 6]: 0 [0x00]
[ 7]: 16 [0x10]
[ 8]: 0 [0x00]
[ 9]: 0 [0x00]
[10]: 0 [0x00]
[11]: 0 [0x00]
[12]: 0 [0x00]
[13]: 0 [0x00]
[14]: 0 [0x00]
[15]: 0 [0x00]
** UNION OR: ( cmd - Command Descriptor Block issued ) **
lw - CDB as longwords:
[0]: 4127588399 [0xf606002f]
[1]: 268435600 [0x10000090]
[2]: 0 [0x00]
[3]: 0 [0x00]
** UNION OR: ( cmd - Command Descriptor Block issued ) **
cdb6 (6 Byte CDB by field)
opcode - Offset 0 -- Operation Code: 47 [0x2f]
Flag field bits: 00000000
Offset 1, Bits 0-4 -- Logical Block Address[0]: 0
Offset 1, Bits 5-7 -- Logical Unit Number (obsolete method -- unused): 0
lba1 - Offset 2 -- Logical Block Address[1]: 6 [0x06]
lba2 - Offset 3 -- Logical Block Address[2]: 246 [0xf6]
length - Offset 4 -- Length: 144 [0x90]
control - Offset 5 -- Control: 0 [0x00]
padding - Offsets 6-7 -- Pad to longword align: 4096 [0x1000]
** UNION OR: ( cmd - Command Descriptor Block issued ) **
cdb10 (10 Byte CDB by field)
opcode - Offset 0 -- Operation Code: 47 [0x2f]
Flag field bits: 00000000
Offset 1, Bits 0-4 -- Reserved: 0
Offset 1, Bits 5-7 -- Logical Unit Number (obsolete method -- unused): 0
lba0 - Offset 2 -- Logical Block Address[0]: 6 [0x06]
lba1 - Offset 3 -- Logical Block Address[1]: 246 [0xf6]
lba2 - Offset 4 -- Logical Block Address[2]: 144 [0x90]
lba3 - Offset 5 -- Logical Block Address[3]: 0 [0x00]
reserved6 - Offset 6 -- Reserved: 0 [0x00]
length0 - Offset 7 -- Length[0]: 16 [0x10]
length1 - Offset 8 -- Length[1]: 0 [0x00]
control - Offset 9 -- Control: 0 [0x00]
padding - Offsets 10-11 -- Pad to longword align: 0 [0x00]
** UNION OR: ( cmd - Command Descriptor Block issued ) **
cdb12 (12 Byte CDB by field)
opcode - Offset 0 -- Operation Code: 47 [0x2f]
Flag field bits: 00000000
Offset 1, Bits 0-4 -- Reserved: 0
Offset 1, Bits 5-7 -- Logical Unit Number (obsolete method -- unused): 0
lba0 - Offset 2 -- Logical Block Address[0]: 6 [0x06]
lba1 - Offset 3 -- Logical Block Address[1]: 246 [0xf6]
lba2 - Offset 4 -- Logical Block Address[2]: 144 [0x90]
lba3 - Offset 5 -- Logical Block Address[3]: 0 [0x00]
length0 - Offset 6 -- Length[0]: 0 [0x00]
length1 - Offset 7 -- Length[1]: 16 [0x10]
length2 - Offset 8 -- Length[2]: 0 [0x00]
length3 - Offset 9 -- Length[3]: 0 [0x00]
reserved10 - Offset 10 -- Reserved: 0 [0x00]
control - Offset 11 -- Control: 0 [0x00]
** UNION OR: ( cmd - Command Descriptor Block issued ) **
cdb16 (16 Byte CDB by field)
opcode - Offset 0 -- Operation Code: 47 [0x2f]
parameter - Offset 1 -- Command specific parameters: 0 [0x00]
lba0 - Offset 2 -- Logical Block Address[0]: 6 [0x06]
lba1 - Offset 3 -- Logical Block Address[1]: 246 [0xf6]
lba2 - Offset 4 -- Logical Block Address[2]: 144 [0x90]
lba3 - Offset 5 -- Logical Block Address[3]: 0 [0x00]
lba4 - Offset 6 -- Logical Block Address[4] or Operation Length[0]: 0 [0x00]
lba5 - Offset 7 -- Logical Block Address[5] or Operation Length[1]: 16 [0x10]
lba6 - Offset 8 -- Logical Block Address[6] or Operation Length[2]: 0 [0x00]
lba7 - Offset 9 -- Logical Block Address[7] or Operation Length[3]: 0 [0x00]
length0 - Offset 10 -- Length[0]: 0 [0x00]
length1 - Offset 11 -- Length[1]: 0 [0x00]
length2 - Offset 12 -- Length[2]: 0 [0x00]
length3 - Offset 13 -- Length[3]: 0 [0x00]
reserved - Offsets 14 -- Reserved: 0 [0x00]
control - Offset 15 -- Control: 0 [0x00]
** END UNION: ( cmd - Command Descriptor Block issued ) **
** NOTE: The following is part of a UNION with more than one interpretation.
You will need to determine which union value is relevant.
** START UNION: ( error - Sense data reported by the physical disk drive ) **
bytes - Sense data as bytes:
[ 0]: 240 [0xf0]
[ 1]: 0 [0x00]
[ 2]: 1 [0x01]
[ 3]: 6 [0x06]
[ 4]: 246 [0xf6]
[ 5]: 146 [0x92]
[ 6]: 2 [0x02]
[ 7]: 10 [0x0a]
[ 8]: 0 [0x00]
[ 9]: 0 [0x00]
[10]: 0 [0x00]
[11]: 0 [0x00]
[12]: 24 [0x18]
[13]: 0 [0x00]
[14]: 9 [0x09]
[15]: 128 [0x80]
[16]: 1 [0x01]
[17]: 40 [0x28]
[18]: 0 [0x00]
[19]: 0 [0x00]
** UNION OR: ( error - Sense data reported by the physical disk drive ) **
lw - Sense data as longwords:
[0]: 100729072 [0x060100f0]
[1]: 167940854 [0x0a0292f6]
[2]: 0 [0x00]
[3]: 2148073496 [0x80090018]
[4]: 10241 [0x2801]
** UNION OR: ( error - Sense data reported by the physical disk drive ) **
sense_data (Sense data by field)
Flag field bits: 11110000
Offset 0, Bits 0-6 -- Error Code: 70
Offset 0, Bit 7 -- Valid: TRUE
segment - Offset 1 -- Segment: 0 [0x00]
Flag field bits: 00000001
Offset 2, Bits 0-3 -- Sense Key: 1
Offset 2, Bit 4 -- Reserved: FALSE
Offset 2, Bit 5 -- Incorrect Length Indicator: FALSE
Offset 2, Bit 6 -- End of Medium: FALSE
Offset 2, Bit 7 -- Filemark: FALSE
info_0 - Offset 3 -- Information[0]: 6 [0x06]
info_1 - Offset 4 -- Information[1]: 246 [0xf6]
info_2 - Offset 5 -- Information[2]: 146 [0x92]
info_3 - Offset 6 -- Information[3]: 2 [0x02]
add_length - Offset 7 -- Additional Sense Length: 10 [0x0a]
cmd_specific - Offsets 8-11 -- Command Specific Information:
[0]: 0 [0x00]
[1]: 0 [0x00]
[2]: 0 [0x00]
[3]: 0 [0x00]
** NOTE: The following is part of a UNION with more than one interpretation.
You will need to determine which union value is relevant.
** START UNION: ( asc_ascq - ASC/ASCQ Union ) **
asc_ascqb (Offsets 12-13 -- Additional Sense Code (ASC)/Additional Sense Code Qualifier (ASCQ))
asc - Offset 12 -- ASC: 24 [0x18]
asq - Offset 13 -- ASCQ: 0 [0x00]
** UNION OR: ( asc_ascq - ASC/ASCQ Union ) **
asc_ascqw - Offsets 12-13 -- Combined ASC/ASCQ: 24 [0x18]
** END UNION: ( asc_ascq - ASC/ASCQ Union ) **
fru_code - Offset 14 -- Field Replaceable Unit Code: 9 [0x09]
Flag field bits: 10000000
Offset 15, Bits 0-6 -- Sense Key Specific[0]: 0
Offset 15, Bit 7 -- Sense Key Specific Valid: TRUE
sks - Offsets 16-17 -- Sense Key Specific[1-2]:
[0]: 1 [0x01]
[1]: 40 [0x28]
padding - Offsets 18-19 -- Pad to longword align: 0 [0x00]
** END UNION: ( error - Sense data reported by the physical disk drive ) **
enclosures[1] (Enclosure available on the Fibre Channel port identified in the cerp_id and port fields)
rack_num - Rack were enclosure is located: 0 [0x00]
dencl_num - Enclosure number: 1 [0x01]
enclosures[0] (Enclosure available on the Fibre Channel port identified in the cerp_id and port fields)
rack_num - Rack were enclosure is located: 0 [0x00]
dencl_num - Enclosure number: 2 [0x02]
enclosures[3] (Enclosure available on the Fibre Channel port identified in the cerp_id and port fields)
rack_num - Rack were enclosure is located: 0 [0x00]
dencl_num - Enclosure number: 99 [0x63]
enclosures[2] (Enclosure available on the Fibre Channel port identified in the cerp_id and port fields)
rack_num - Rack were enclosure is located: 0 [0x00]
dencl_num - Enclosure number: 99 [0x63]
enclosures[5] (Enclosure available on the Fibre Channel port identified in the cerp_id and port fields)
rack_num - Rack were enclosure is located: 0 [0x00]
dencl_num - Enclosure number: 99 [0x63]
enclosures[4] (Enclosure available on the Fibre Channel port identified in the cerp_id and port fields)
rack_num - Rack were enclosure is located: 0 [0x00]
dencl_num - Enclosure number: 99 [0x63]
enclosures[7] (Enclosure available on the Fibre Channel port identified in the cerp_id and port fields)
rack_num - Rack were enclosure is located: 0 [0x00]
dencl_num - Enclosure number: 99 [0x63]
enclosures[6] (Enclosure available on the Fibre Channel port identified in the cerp_id and port fields)
rack_num - Rack were enclosure is located: 0 [0x00]
dencl_num - Enclosure number: 99 [0x63]
enclosures[9] (Enclosure available on the Fibre Channel port identified in the cerp_id and port fields)
rack_num - Rack were enclosure is located: 0 [0x00]
dencl_num - Enclosure number: 99 [0x63]
enclosures[8] (Enclosure available on the Fibre Channel port identified in the cerp_id and port fields)
rack_num - Rack were enclosure is located: 0 [0x00]
dencl_num - Enclosure number: 99 [0x63]
*** End of Data *** |
|
免费注册
发表于 2010-09-13 14:28
