日志中的奇怪报错，网络不通

atianyu

请高手帮忙看看，以下报错说明什么？不知道有人遇到过没
另外这台机器总过一段时间无法PING通，然后就会产生如下的报错

[root@ypyc-candy log]# tail -200 messages|grep error
Jan  3 16:54:00 ypyc-candy insmod: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.       You may find more information in syslog or the output from dmesg

7717060

dmesg | grep error 发上来

gamester88

You may find more information in syslog or the output from dmesg

dmesg的信息呢

atianyu

奇怪的是dmesg里没有error信息，如下
[root@ypyc-candy root]# dmesg|grep error
[root@ypyc-candy root]# dmesg
reporting enabled on CPU#0.
CPU:     After generic, caps: bfebfbff 00000000 00000000 00000000
CPU:             Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel(R) Xeon(TM) MP CPU 2.20GHz stepping 06
per-CPU timeslice cutoff: 1463.06 usecs.
task migration cache decay timeout: 10 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4377.80 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: L3 cache: 2048K
ACPI tables and CPU MSR values mismatch about cpu number
CPU: Physical Processor ID: 1
Intel machine check reporting enabled on CPU#1.
CPU:     After generic, caps: bfebfbff 00000000 00000000 00000000
CPU:             Common caps: bfebfbff 00000000 00000000 00000000
CPU1: Intel(R) Xeon(TM) MP CPU 2.20GHz stepping 06
Booting processor 2/2 eip 2000
Initializing CPU#2
masked ExtINT on CPU#2
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4377.80 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: L3 cache: 2048K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#2.
CPU:     After generic, caps: bfebfbff 00000000 00000000 00000000
CPU:             Common caps: bfebfbff 00000000 00000000 00000000
CPU2: Intel(R) Xeon(TM) MP CPU 2.20GHz stepping 06
Booting processor 3/3 eip 2000
Initializing CPU#3
masked ExtINT on CPU#3
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4377.80 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: L3 cache: 2048K
CPU: Physical Processor ID: 1
Intel machine check reporting enabled on CPU#3.
CPU:     After generic, caps: bfebfbff 00000000 00000000 00000000
CPU:             Common caps: bfebfbff 00000000 00000000 00000000
CPU3: Intel(R) Xeon(TM) MP CPU 2.20GHz stepping 06
Total of 4 processors activated (17498.11 BogoMIPS).
apic 0 pin 9 is an SMI pin!
apic 1 pin 1 is an SMI pin!
ENABLING IO-APIC IRQs
Setting 14 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 14 ... ok.
Setting 13 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 13 ... ok.
Setting 12 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 12 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 14-0, 14-5, 14-7, 14-9, 14-10, 14-11, 13-0, 13-1, 13-2, 13-3 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
number of MP IRQ sources: 38.
number of IO-APIC #14 registers: 16.
number of IO-APIC #13 registers: 16.
number of IO-APIC #12 registers: 16.
testing the IO APIC.......................

IO APIC #14......
.... register #00: 0E000000
.......    : physical APIC id: 0E
.......    : Delivery Type: 0
.......    : LTS          : 0
.... register #01: 000F0011
.......     : max redirection entries: 000F
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 0E000000
.......     : arbitration: 0E
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
00 000 00  1    0    0   0   0    0    0    00
01 00F 0F  0    0    0   0   0    1    1    39
02 00F 0F  0    0    0   0   0    1    1    31
03 00F 0F  1    1    0   1   0    1    1    41
04 00F 0F  0    0    0   0   0    1    1    49
05 000 00  1    0    0   0   0    0    0    00
06 00F 0F  0    0    0   0   0    1    1    51
07 000 00  1    0    0   0   0    0    0    00
08 00F 0F  0    0    0   0   0    1    1    59
09 024 04  1    0    0   0   0    0    2    00
0a 000 00  1    0    0   0   0    0    0    00
0b 000 00  1    0    0   0   0    0    0    00
0c 00F 0F  0    0    0   0   0    1    1    61
0d 00F 0F  0    0    0   0   0    1    1    69
0e 00F 0F  0    0    0   0   0    1    1    71
0f 00F 0F  0    0    0   0   0    1    1    79

IO APIC #13......
.... register #00: 0D000000
.......    : physical APIC id: 0D
.......    : Delivery Type: 0
.......    : LTS          : 0
.... register #01: 000F0011
.......     : max redirection entries: 000F
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 0D000000
.......     : arbitration: 0D
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
00 000 00  1    0    0   0   0    0    0    00
01 000 00  1    0    0   0   0    0    2    2C
02 000 00  1    0    0   0   0    0    0    00
03 000 00  1    0    0   0   0    0    0    00
04 00F 0F  1    1    0   1   0    1    1    81
05 00F 0F  1    1    0   1   0    1    1    89
06 00F 0F  1    1    0   1   0    1    1    91
07 00F 0F  1    1    0   1   0    1    1    99
08 00F 0F  1    1    0   1   0    1    1    A1
09 00F 0F  1    1    0   1   0    1    1    A9
0a 00F 0F  1    1    0   1   0    1    1    B1
0b 00F 0F  1    1    0   1   0    1    1    B9
0c 00F 0F  1    1    0   1   0    1    1    C1
0d 00F 0F  1    1    0   1   0    1    1    C9
0e 00F 0F  1    1    0   1   0    1    1    D1
0f 00F 0F  1    1    0   1   0    1    1    D9

IO APIC #12......
.... register #00: 0C000000
.......    : physical APIC id: 0C
.......    : Delivery Type: 0
.......    : LTS          : 0
.... register #01: 000F0011
.......     : max redirection entries: 000F
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 0C000000
.......     : arbitration: 0C
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
00 00F 0F  1    1    0   1   0    1    1    E1
01 00F 0F  1    1    0   1   0    1    1    E9
02 00F 0F  1    1    0   1   0    1    1    32
03 00F 0F  1    1    0   1   0    1    1    3A
04 00F 0F  1    1    0   1   0    1    1    42
05 00F 0F  1    1    0   1   0    1    1    4A
06 00F 0F  1    1    0   1   0    1    1    52
07 00F 0F  1    1    0   1   0    1    1    5A
08 00F 0F  1    1    0   1   0    1    1    62
09 00F 0F  1    1    0   1   0    1    1    6A
0a 00F 0F  1    1    0   1   0    1    1    72
0b 00F 0F  1    1    0   1   0    1    1    7A
0c 00F 0F  1    1    0   1   0    1    1    82
0d 00F 0F  1    1    0   1   0    1    1    8A
0e 00F 0F  1    1    0   1   0    1    1    92
0f 00F 0F  1    1    0   1   0    1    1    9A
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ8 -> 0:8
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ20 -> 1:4
IRQ21 -> 1:5
IRQ22 -> 1:6
IRQ23 -> 1:7
IRQ24 -> 1:8
IRQ25 -> 1:9
IRQ26 -> 1:10
IRQ27 -> 1:11
IRQ28 -> 1:12
IRQ29 -> 1:13
IRQ30 -> 1:14
IRQ31 -> 1:15
IRQ32 -> 2:0
IRQ33 -> 2:1
IRQ34 -> 2:2
IRQ35 -> 2:3
IRQ36 -> 2:4
IRQ37 -> 2:5
IRQ38 -> 2:6
IRQ39 -> 2:7
IRQ40 -> 2:8
IRQ41 -> 2:9
IRQ42 -> 2:10
IRQ43 -> 2:11
IRQ44 -> 2:12
IRQ45 -> 2:13
IRQ46 -> 2:14
IRQ47 -> 2:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2189.4911 MHz.
..... host bus clock speed is 99.5222 MHz.
cpu: 0, clocks: 995222, slice: 199044
CPU0<T0:995216,T1:796160,D:12,S:199044,C:995222>
cpu: 1, clocks: 995222, slice: 199044
cpu: 3, clocks: 995222, slice: 199044
cpu: 2, clocks: 995222, slice: 199044
CPU1<T0:995216,T1:597120,D:8,S:199044,C:995222>
CPU2<T0:995216,T1:398080,D:4,S:199044,C:995222>
CPU3<T0:995216,T1:199040,D:0,S:199044,C:995222>
cpu_sibling_map[0] = 2
cpu_sibling_map[1] = 3
cpu_sibling_map[2] = 0
cpu_sibling_map[3] = 1
mapping CPU#0's runqueue to CPU#2's runqueue.
mapping CPU#1's runqueue to CPU#3's runqueue.
zapping low mappings.
Process timing init...done.
Starting migration thread for cpu 0
Starting migration thread for cpu 1
Starting migration thread for cpu 2
Starting migration thread for cpu 3
PCI: PCI BIOS revision 2.10 entry at 0xfd74c, last bus=12
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:0f.1
PCI: Discovered peer bus 08
PCI: Discovered peer bus 09
PCI->APIC IRQ transform: (B0,I9,P0) -> 46
PCI->APIC IRQ transform: (B0,I15,P0) -> 3
PCI->APIC IRQ transform: (B8,I10,P0) -> 44
PCI->APIC IRQ transform: (B8,I10,P1) -> 45
PCI->APIC IRQ transform: (B9,I8,P0) -> 47
PCI->APIC IRQ transform: (B10,I8,P0) -> 20
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Total HugeTLB memory allocated, 0
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 131061
aio_setup: sizeof(struct page) = 60
Hugetlbfs mounted.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-0 with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks CSB5: IDE controller at PCI slot 00:0f.1
SvrWks CSB5: chipset revision 147
SvrWks CSB5: not 100% native mode: will probe irqs later
SvrWks CSB5: simplex device: DMA forced
    ide0: BM-DMA at 0x0700-0x0707, BIOS settings: hdaMA, hdbMA
SvrWks CSB5: simplex device: DMA forced
    ide1: BM-DMA at 0x0708-0x070f, BIOS settings: hdcMA, hddMA
hda: HL-DT-ST CD-ROM GCR-8482B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP: Hash tables configured (established 524288 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
Initializing IPsec netlink socket
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 329k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
        <Adaptec aic7899 Ultra160 SCSI adapter>
        aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs

scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
        <Adaptec aic7899 Ultra160 SCSI adapter>
        aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs

Starting timer : 0 0
blk: queue f7fc3a18, I/O limit 4095Mb (mask 0xffffffff)
(scsi1:A:6): 80.000MB/s transfers (40.000MHz, offset 32, 16bit)
Starting timer : 0 0
  Vendor: SEAGATE   Model: DAT    9SP40-000  Rev: 910B
  Type:   Sequential-Access                  ANSI SCSI revision: 03
Starting timer : 0 0
blk: queue f7fc3818, I/O limit 4095Mb (mask 0xffffffff)
Warning ! ! ! ServeRAID Version Mismatch
Bios = 6.10.24, Firmware = 6.10.24, Device Driver = 6.00.26
These levels should match to avoid possible compatibility problems.
Warning ! ! ! ServeRAID Version Mismatch
Bios = 6.10.24, Firmware = 6.10.24, Device Driver = 6.00.26
These levels should match to avoid possible compatibility problems.
scsi2 : IBM PCI ServeRAID 6.00.26
Starting timer : 0 0
  Vendor: IBM       Model: SERVERAID         Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Starting timer : 0 0
  Vendor: IBM       Model: SERVERAID         Rev: 1.00
  Type:   Processor                          ANSI SCSI revision: 02
Starting timer : 0 0
  Vendor: IBM       Model: 02R0980a S320  1  Rev: 1   
  Type:   Processor                          ANSI SCSI revision: 02
Starting timer : 0 0
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
SCSI device sda: 430116864 512-byte hdwr sectors (220220 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 224k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xf88c2000, IRQ 3
usb-ohci.c: usb-00:0f.2, ServerWorks OSB4/CSB5 OHCI USB Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 4 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
Adding Swap: 2096220k swap-space (priority -1)
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
st: Version 20030406, bufsize 32768, max init. bufs 4, s/g segs 16
Attached scsi tape st0 at scsi1, channel 0, id 6, lun 0
IA-32 Microcode Update Driver: v1.11 <tigran@veritas.com>
inserting floppy driver for 2.4.21-4.ELsmp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
tg3.c:v2.2 (August 24, 2003)
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(BCM95703) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:02:55:df:cc:97
divert: freeing divert_blk for eth0
i8253 count too high! resetting..
i8253 count too high! resetting..
i8253 count too high! resetting..
ip_tables: (C) 2000-2002 Netfilter core team
tg3.c:v2.2 (August 24, 2003)
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(BCM95703) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:02:55:df:cc:97
ip_tables: (C) 2000-2002 Netfilter core team
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
lp: driver loaded but no devices found
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ide-floppy driver 0.99.newide
hda: attached ide-cdrom driver.
hda: ATAPI 48X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
cdrom: This disc doesn't have any tracks I recognize!
st0: Block limits 1 - 16777215 bytes.
tg3: eth0: Link is down.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
[root@ypyc-candy root]#

7717060

觉的是系统的某模块有问题，那你ping不通是指访问不了机器了？还是怎么，能连通80吗？
ifconfig的
     RX packets:497197851 errors:0 dropped:0 overruns:0 frame:0
          TX packets:79185177 errors:0 dropped:0 overruns:0 carrier:0
有有问题的吗？

atianyu

PING不通是指我无法从远程去PING这台机器，也无法连接过去
ifconfig也没问题
RX packets:961084 errors:0 dropped:0 overruns:0 frame:0
          TX packets:313681 errors:0 dropped:0 overruns:0 carrier:0

[ 本帖最后由 atianyu 于 2010-1-6 13:00 编辑 ]

7717060

原帖由 atianyu 于 2010-1-6 12:58 发表
PING不通是指我无法从远程去PING这台机器，也无法连接过去
ifconfig也没问题
RX packets:961084 errors:0 dropped:0 overruns:0 frame:0
          TX packets:313681 errors:0 dropped:0 overruns:0 carrier:0

http://www.google.cn/search?hl=z ... O+or+IRQ+parameters

atianyu

谢谢版主的跟帖
Jan  3 16:54:00 ypyc-candy insmod: /lib/modules/2.4.21-4.ELsmp/kernel/drivers/parport/parport_pc.o: init_module: Device or resource busy
Jan  3 16:54:00 ypyc-candy insmod: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.       You may                                    find more information in syslog or the output from dmesg
Jan  3 16:54:00 ypyc-candy insmod: /lib/modules/2.4.21-4.ELsmp/kernel/drivers/parport/parport_pc.o: insmod parport_lowlevel failed
Jan  3 16:54:00 ypyc-candy kernel: lp: driver loaded but no devices found
Jan  3 16:54:01 ypyc-candy modprobe: modprobe: Can't locate module char-major-188
现补充一下这个报错信息前后的一些不正常的输出，看有什么启发吗，对大家

blueswxs

楼主试试这个办法（治标）：

ifconfig eth0 down
ifconfig eth0 up
ping   xx.xx.xx.xx

看看有没有效果

atianyu

恩，不过现在这台机器目前正常，因为前面几次客户都是在不通的时候自己吧机器给重启后就通了
所以我期待下次问题重现