jz4740根文件系统移植成功，启动信息显示

ecbtnrt

##移植的过程和遇到的问题解析我会整理成文档，让大家来下载，谢谢支持##
NAND Secondary Program Loader
Starting U-Boot ...
U-Boot 1.1.6 (Oct 31 2007 - 17:25:45)
Board: Ingenic PAVO (CPU Speed 336 MHz)   板子是pavo
DRAM: 64 MB
Flash: 0 kB
NAND:1024 MiB
In:    serial
Out:   lcd
Err:   lcd
Hit any key to stop autoboot:  0
NAND read: device 0 offset 0x400000, size 0x700000
7340032 bytes read: OK
## Booting image at 80600000 ...
   Image Name:   Linux-2.6.22
   Image Type:   MIPS Linux Kernel Image (gzip compressed) mips的体系结构
   Data Size:    3036697 Bytes =  2.9 MB
   Load Address: 80100000
   Entry Point:  804fb000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Starting kernel ...
Linux version 2.6.22 (
root@localhost.localdomain
) (gcc version 4.1.2) #4 PREEMPT
Tue Jan 6 09:08:14 CST 2009
CPU revision is: 0ad0024f
System clocks setup: cclk=336MHZ hclk=112MHZ pclk=112MHZ mclk=112MHZ
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 16256
Kernel command line: mem=64M console=ttyS0,57600n8 ip=off rootfstype=yaffs2 root
=/dev/mtdblock5 rdinit=/sbin/init          nand的分配，观察解决问题的能力
Primary instruction cache 16kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 58380k/65536k available (3308k kernel code, 7096k reserved, 763k data, 1
292k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
Total 4MB memory at 0x3c00000 was reserved for IPU
PM initialize
yaffs Jan  6 2009 08:31:55 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
LCDC: PixClock:9081081 LcdClock:25846153
Console: switching to colour frame buffer device 60x34
fb0: jz-lcd frame buffer device, using 512K of video memory
JzSOC onchip RTC installed !!!
JzSOC Watchdog Timer: timer margin 60 sec
JzSOC: char device family.
JzSOC Camera Interface Module (CIM) driver registered
Ingenic CMOS camera sensor driver registered
Jz generic touch screen driver registered
JZ4740 SAR-ADC driver registered
UDC starting monitor thread
JZ UDC hotplug driver installed
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
Jz CS8900A driver for Linux (V0.02)
eth%d: CS8900A rev E detected
block2mtd: version $Revision: 1.30 $
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 6 MTD partitions on "NAND 1GiB 3,3V 8-bit":
0x00000000-0x00400000 : "NAND BOOT partition"
0x00400000-0x00800000 : "NAND KERNEL partition"
0x00800000-0x08000000 : "NAND ROOTFS partition"
0x08000000-0x10000000 : "NAND DATA1 partition"
0x10000000-0x20000000 : "NAND DATA2 partition"
0x20000000-0x40000000 : "NAND VFAT partition"      注意观察vfat
jz-ohci jz-ohci.0: JZ OHCI
jz-ohci jz-ohci.0: new USB bus registered, assigned bus number 1
jz-ohci jz-ohci.0: irq 3, io mem 0x13030000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
JZ SD/MMC card driver registered
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 200
7 UTC).
ASoC version 0.13.1
Pavo initialization...
jzcodec: Icodec Audio Codec 1.0
out:0
asoc: JZCODEC  jz4740-i2s mapping ok
ALSA device list:
  #0: Pavo (JZCODEC)
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 1292k freed
Algorithmics/MIPS FPU Emulator v1.5
init started: BusyBox v1.8.2 (2009-01-05 22:36:15 CST)
starting pid 723, tty '': '/etc/init.d/rcS'
Cannot run '/etc/init.d/rcS': No such file or directory  这是什么问题呢
Please press Enter to activate this console.
starting pid 724, tty '': '/bin/sh'
/ #


本文来自ChinaUnix博客，如果查看原文请点：http://blog.chinaunix.net/u3/91151/showart_1791804.html