免费注册 查看新帖 |

Chinaunix

  平台 论坛 博客 文库
最近访问板块 发新帖
查看: 3926 | 回复: 1
打印 上一主题 下一主题

天敏电视大师三在debian4下用TVTIME看电视声音很小!! [复制链接]

论坛徽章:
0
跳转到指定楼层
1 [收藏(0)] [报告]
发表于 2007-05-04 22:50 |只看该作者 |倒序浏览
在网上搜索了很多方法,都没能解决这个问题,电视图象正常,就是声音很小,在gnome下调声音没反应,用终端里alsamixer也不行!以下是相关信息:请各位帮忙为感!!
#cat /etc/modprobe.d/saa7134
#options saa7134 card=21 tuner=61
options saa7134 card=21,21,21,21 tuner=38,38,38,38 video_nr=0,1,2,3 vbi_nr=0,1,2,3 radio_nr=0,1,2,3
install saa7134 /sbin/modprobe --ignore-install saa7134; /sbin/modprobe saa7134-alsa
options saa7134-alsa index=1,2,3,4

# dmesg
Linux version 2.6.18-4-486 (Debian 2.6.18.dfsg.1-12etch1) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Wed Apr 18 09:13:09 UTC 2007
251MB LOWMEM available.
On node 0 totalpages: 64496
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 60400 pages, LIFO batch:15
DMI 2.2 present.
ACPI: RSDP (v000 AWARD                                 ) @ 0x000f6720
ACPI: RSDT (v001 AWARD  AWRDACPI 0x00000000  0x00000000) @ 0x0fbf3000
ACPI: FADT (v001 AWARD  AWRDACPI 0x00000000  0x00000000) @ 0x0fbf3040
ACPI: DSDT (v001 AWARD  AWRDACPI 0x00001000 MSFT 0x0100000a) @ 0x00000000
ACPI: PM-Timer IO Port: 0x5008
Allocating PCI resources starting at 10000000 (gap: 0fc00000:f03f0000)
Detected 548.642 MHz processor.
Built 1 zonelists.  Total pages: 64496
Kernel command line: root=/dev/hda8 ro
No local APIC present or hardware disabled
mapped APIC to ffffd000 (011f9000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 248272k/257984k available (1502k kernel code, 9108k reserved, 601k data, 256k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1097.85 BogoMIPS (lpj=2195711)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 008021bf c08029bf 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 008021bf c08029bf 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: L2 Cache: 128K (32 bytes/line)
CPU: After all inits, caps: 008021bf c08029bf 00000000 00000002 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
CPU: AMD-K6(tm)-III Processor stepping 04
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 8ca0)
checking if image is initramfs... it is
Freeing initrd memory: 4268k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb3c0, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:00.1
Boot video device is 0000:00:09.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 *7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:02.0
  IO window: c000-cfff
  MEM window: ef800000-ef8fffff
  PREFETCH window: ef000000-ef7fffff
PCI: Enabling device 0000:00:02.0 (0000 -> 0003)
PCI: Setting latency timer of device 0000:00:02.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1178316507.064:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303S2K,PNP0f13S2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI: (supports S0 S1 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 256k freed
input: AT Translated Set 2 keyboard as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:00.1
ACPI: Unable to derive IRQ for device 0000:00:00.1
ACPI: PCI Interrupt 0000:00:00.1[A]: no GSI - using IRQ 14
PCI: setting IRQ 14 as level-triggered
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS530 ATA 66 controller
    ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hdaMA, hdb:pio
Probing IDE interface ide0...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
hda: ST340810A, ATA DISK drive
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
8139too Fast Ethernet driver 0.9.27
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:01.2[A] -> Link [LNKE] -> GSI 7 (level, low) -> IRQ 7
ohci_hcd 0000:00:01.2: OHCI Host Controller
ohci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:01.2: irq 7, io mem 0xef981000
hda: max request size: 128KiB
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 hda7ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xd000, 00:0a:eb:4a:72:42, IRQ 11
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
hda8 hda9 >
usb 1-1: new low speed USB device using ohci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: Logitech Optical USB Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:01.2-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Attempting manual resume
ReiserFS: hda8: found reiserfs format "3.6" with standard journal
ReiserFS: hda8: using ordered data mode
ReiserFS: hda8: journal params: device hda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda8: checking transaction log (hda
ReiserFS: hda8: Using r5 hash to sort names
ts: Compaq touchscreen protocol output
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
sis630_smbus 0000:00:01.0: SIS630 comp. bus not detected, module not inserted.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected SiS 530 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
input: PC Speaker as /class/input/input2
Real Time Clock Driver v1.12ac
Linux video capture interface: v2.00
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
saa7130[0]: found at 0000:00:0b.0, rev: 1, irq: 5, latency: 64, mmio: 0xef982000saa7130[0]: subsystem: 1131:2304, board: 10MOONS PCI TV CAPTURE CARD [card=21,insmod option]

论坛徽章:
0
2 [报告]
发表于 2007-05-04 22:52 |只看该作者

续,一次发不了!

saa7130[0]: board init: gpio is efbbe00
saa7130[0]: i2c eeprom 00: 31 11 04 23 08 20 1c 55 43 43 a9 1c 55 43 43 a9
saa7130[0]: i2c eeprom 10: ff ff 00 00 31 30 4d 4f 4f 4e 53 37 31 33 30 20
saa7130[0]: i2c eeprom 20: 54 04 48 53 ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner 1-0060: All bytes are equal. It is not a TEA5767
tuner 1-0060: chip found @ 0xc0 (saa7130[0])
tuner 1-0060: type set to 37 (LG PAL (newer TAPC series))
tuner 1-0061: chip found @ 0xc2 (saa7130[0])
saa7130[0]: registered device video0 [v4l2]
saa7130[0]: registered device vbi0
saa7130[0]: registered device radio0
saa7134 ALSA driver for DMA sound loaded
saa7130[0]/alsa: saa7130[0] at 0xef982000 irq 5 registered as card 1
input: PS/2 Generic Mouse as /class/input/input3
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
gameport: ES1938 is pci0000:00:0c.0/gameport0, io 0xe400, speed 1011kHz
Adding 441748k swap on /dev/hda7.  Priority:-1 extents:1 across:441748k
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
ReiserFS: hda9: found reiserfs format "3.6" with standard journal
ReiserFS: hda9: using ordered data mode
ReiserFS: hda9: journal params: device hda9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda9: checking transaction log (hda9)
ReiserFS: hda9: Using r5 hash to sort names
NTFS driver 2.1.27 [Flags: R/W MODULE].
NTFS-fs warning (device hda1): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs error (device hda1): load_system_files(): $LogFile is not clean.  Mounting read-only.  Mount in Windows.
NTFS-fs warning (device hda6): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
NTFS-fs error (device hda6): load_system_files(): Volume is dirty.  Mounting read-only.  Run chkdsk and mount in Windows.
NTFS-fs warning (device hda6): load_system_files(): $LogFile is not clean.  Will not be able to remount read-write.  Mount in Windows.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 24
ip_tables: (C) 2000-2006 Netfilter Core Team
eth0: no IPv6 routers present
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
您需要登录后才可以回帖 登录 | 注册

本版积分规则 发表回复

  

北京盛拓优讯信息技术有限公司. 版权所有 京ICP备16024965号-6 北京市公安局海淀分局网监中心备案编号:11010802020122 niuxiaotong@pcpop.com 17352615567
未成年举报专区
中国互联网协会会员  联系我们:huangweiwei@itpub.net
感谢所有关心和支持过ChinaUnix的朋友们 转载本站内容请注明原作者名及出处

清除 Cookies - ChinaUnix - Archiver - WAP - TOP