Suse9如何正确安装HBA卡驱动!!!

yjyf8026

两台SUN4200服务器操作系统为：Suse9sp3 for x86
两块Qlogic2460的HBA卡
IBMds400磁盘阵列
1、安装了驱动之后，磁盘阵列的挂载很不稳定。不定时地就有一台服务器看不到磁盘阵了
   用Fdisk -l 命令看不到/dev/sdb的存在，另一台可以正常的挂载。
   解决办法：重新启动服务器*重新启动磁盘阵列
   但是我总觉得这种情况不正常
2、安装在服务器上面的HBA的指示灯显示的黄灯常亮。
   正常的是不是应该绿灯常亮啊，请大侠指点指示灯正常亮度。
3、有哪位大侠有suse9下面安装HBA卡驱动的安装文档，兄弟在这里谢过了！
4、我是安装Qlogic的网站上的安装说明去装的，解压之后驱动包qla2xxx-v8.01.06-dist.tgz
     然后就执行了如下命令：
   a、打补丁包：
    #rpm –ivh QLogicHBACIMProvider-SLES9x86_64-1.10.01-rel.x86_64.rpm
    B、安装驱动：
    #tar xzvf qla2xxx-v8.01.06-dist.tgz
    之后该目录下产生：qlogic目录。
    #cd qlogic
      # ls
   README.qla2xxx  libremove qlapi-v2.03build15-rel.tgz drvrsetup    readme.txt ApiPkg  
libinstall      qla2xxx-src-v8.01.06.tar.gz
     #./drvrseup
     #./libinstall
     #./libremove
    之后会产生qla2xxx-8.01.06目录，进入该目录
   #cd qla2xxx-8.01.06
   #ls
    # ./extras/build.sh
    #./extras/build.sh clean
    #./extras/build.sh new
    #./extras/build.sh install
    修改/etc/sysconfig/kerner文件
   #cp kerner kerner_bak
     #vi kerner
     在文件的最后一行加入：
   INITRD_MODULES="aic7xxx qla2xxx_conf qla2xxx qla2400"
   重新启动
   Hba卡驱动生效。

mysea83

默认下面，SLES 9加SP3已经带这个HBA卡的驱动了，应该不需要再安装。
你可以lsmod看一下
还有，安装完，你可以直接用rescan-scsi-bus.sh这个命令来认存储。

yjyf8026

首先非常感谢mysea83的回复，我执行了命令，结果如下。没有发现咚咚。
# rescan-scsi-bus.sh
Host adapter 0 (mptsas) found.
Host adapter 1 (qla2xxx) found.
Host adapter 2 (usb-storage) found.
Host adapter 3 (usb-storage) found.
Scanning hosts  0 1 2 3 channels 0 for
SCSI target IDs  0 1 2 3 4 5 6 7 , LUNs  0
Scanning for device 0 0 0 0 ...
OLD: Host: scsi0 Channel: 00 Id: 00 Lun: 00
      Vendor: SEAGATE  Model: ST973401LSUN72G  Rev: 0556
      Type:   Direct-Access                    ANSI SCSI revision: 03
Scanning for device 2 0 0 0 ...
OLD: Host: scsi2 Channel: 00 Id: 00 Lun: 00
      Vendor: AMI      Model: Virtual CDROM    Rev: 1.00
      Type:   CD-ROM                           ANSI SCSI revision: 02
Scanning for device 3 0 0 0 ...
OLD: Host: scsi3 Channel: 00 Id: 00 Lun: 00
      Vendor: AMI      Model: Virtual Floppy   Rev: 1.00
      Type:   Direct-Access                    ANSI SCSI revision: 02
0 new device(s) found.               
0 device(s) removed.   

我用Fdisk-l 也看不到新增加的磁盘。
我查看了：
WH-SA-1:~ # cd /proc/scsi/qla2xxx/
WH-SA-1:/proc/scsi/qla2xxx # ls
.  ..  1
WH-SA-1:/proc/scsi/qla2xxx # cat 1
结果如下：
QLogic PCI to Fibre Channel Host Adapter for QLA2460:
        Firmware version 4.00.12 [IP] , Driver version 8.01.02-sles
ISP: ISP2422, Serial# K82795
Request Queue = 0x37580000, Response Queue = 0x37530000
Request Queue count = 4096, Response Queue count = 512
Total number of active commands = 0
Total number of interrupts = 619455
    Device queue depth = 0x10
Number of free request entries = 3974
Number of mailbox timeouts = 0
Number of ISP aborts = 0
Number of loop resyncs = 0
Number of retries for empty slots = 0
Number of reqs in pending_q= 0, retry_q= 0, done_q= 0, scsi_retry_q= 0
Host adapter:loop state = <READY>, flags = 0x1c13
Dpc flags = 0x4080000
MBX flags = 0x0
Link down Timeout = 030
Port down retry = 030
Login retry count = 030
Commands retried with dropped frame(s) = 0
Product ID = 0000 0000 0000 0000


SCSI Device Information:
scsi-qla0-adapter-node=200000e08b90ab85;
scsi-qla0-adapter-port=210000e08b90ab85;
scsi-qla0-target-0=21000000d126879d;

FC Port Information:
scsi-qla0-port-0=20000000d126879d:21000000d126879d:0000ef:0;

SCSI LUN Information:
(Id:Lun)  * - indicates lun is not registered with the OS.
( 0: 0): Total reqs 120, Pending reqs 0, flags 0x0, 0:0:00 00
#lsmod
qla2400               193920  0
qla2xxx               322488  2 qla2400
firmware_class          9472  1 qla2xxx
scsi_transport_fc       6912  1 qla2xxx
驱动都有阿，帮忙查看！多谢了

wolfop

FC的 HBA卡正常就是黄灯亮。我也不建议你用qlogic的驱动，用suse el9 sp3自带的应该可以。
看不到盘阵的情况你dmesg一下看看内核报什么错误信息。  另外你的主机和盘阵之间经过交换机了么？
另外就是你的DS400的配置，这个得问问IBM。

yjyf8026

dmesg看到新息如下：

QLogic Fibre Channel HBA Driver
qla2400: module not supported by Novell, setting U taint flag.
ACPI: PCI interrupt 0000:05:01.0[A] -> GSI 11 (level, low) -> IRQ 11
qla2400 0000:05:01.0: Found an ISP2422, irq 11, iobase 0xf91bd000
qla2400 0000:05:01.0: Configuring PCI space...
qla2400 0000:05:01.0: Configure NVRAM parameters...
qla2400 0000:05:01.0: Verifying loaded RISC code...
qla2400 0000:05:01.0: Allocated (1061 KB) for firmware dump...
qla2400 0000:05:01.0: Waiting for LIP to complete...
qla2400 0000:05:01.0: LIP reset occured (f7f7).
qla2400 0000:05:01.0: LIP occured (f7f7).
qla2400 0000:05:01.0: LOOP UP detected (2 Gbps).
qla2400 0000:05:01.0: Topology - (Loop), Host Loop address 0x1
scsi1 : qla2xxx
qla2400 0000:05:01.0:
QLogic Fibre Channel HBA Driver: 8.01.02-sles
  QLogic QLA2460 - Sun PCI-X 2.0 to 4Gb FC, Single Channel
  ISP2422: PCI-X Mode 1 (66 MHz) @ 0000:05:01.0 hdma-, host#=1, fw=4.00.12 [IP]
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 1/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 2/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 3/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 4/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 5/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 6/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 7/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 8/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 9/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 10/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 11/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 12/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 13/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 14/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 15/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 16/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 17/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 18/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 19/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 20/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 21/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 22/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 23/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 24/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 25/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 26/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 27/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 28/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 29/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 30/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 31/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 32/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 33/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 34/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 35/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 36/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 37/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 38/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 39/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 40/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 41/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 42/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 43/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 44/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 45/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 46/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 47/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 48/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 49/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 50/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 51/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 52/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 53/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 54/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 55/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 56/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 57/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 58/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 59/60
scsi1 (0,0,0) BUSY/QUEUE FULL - probe failed
ReiserFS: sda1: found reiserfs format "3.6" with standard journal
ReiserFS: sda1: using ordered data mode
reiserfs: using flush barriers
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
reiserfs: disabling flush barriers on sda1
ReiserFS: sda1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... /initrd does not exist. Ignored.
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 212k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: Allocated new minor_bits array for 1024 devices
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
reiserfs: using flush barriers
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
reiserfs: disabling flush barriers on sda3
ReiserFS: sda3: Using r5 hash to sort names
subfs 0.9
Adding 8393952k swap on /dev/sda2.  Priority:-1 extents:1
Intel(R) PRO/1000 Network Driver - version 6.2.15-NAPI
Copyright (c) 1999-2005 Intel Corporation.
ACPI: PCI interrupt 0000:01:01.0[A] -> GSI 10 (level, low) -> IRQ 10
e1000: 0000:01:01.0: e1000_probe: (PCI-X:100MHz:64-bit) 00:14:4f:46:30:ea
eth0: TCP Segmentation Offload (TSO) disabled by default
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI interrupt 0000:01:01.1[B] -> GSI 11 (level, low) -> IRQ 11
e1000: 0000:01:01.1: e1000_probe: (PCI-X:100MHz:64-bit) 00:14:4f:46:30:eb
eth1: TCP Segmentation Offload (TSO) disabled by default
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI interrupt 0000:01:02.0[A] -> GSI 11 (level, low) -> IRQ 11
e1000: 0000:01:02.0: e1000_probe: (PCI-X:100MHz:64-bit) 00:14:4f:46:30:ec
eth2: TCP Segmentation Offload (TSO) disabled by default
e1000: eth2: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI interrupt 0000:01:02.1[B] -> GSI 9 (level, low) -> IRQ 9
e1000: 0000:01:02.1: e1000_probe: (PCI-X:100MHz:64-bit) 00:14:4f:46:30:ed
eth3: TCP Segmentation Offload (TSO) disabled by default
e1000: eth3: e1000_probe: Intel(R) PRO/1000 Network Connection
Ethernet Channel Bonding Driver: v2.6.5 (November 4, 2005)
bonding: MII link monitoring set to 100 ms
bonding: bond0: enslaving eth0 as a backup interface with a down link.
bonding: bond0: enslaving eth1 as a backup interface with a down link.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
bonding: bond0: link status definitely up for interface eth0.
bonding: bond0: making interface eth0 the new active one.
e1000: eth1: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
bonding: bond0: link status definitely up for interface eth1.
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
IA-32 Microcode Update Driver: v1.13 <tigran@veritas.com>
microcode: CPU0 not a capable Intel processor
microcode: No suitable data for cpu 0
IA-32 Microcode Update Driver v1.13 unregistered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
hw_random: AMD768 system management I/O registers at 0x5000.
tpm: module not supported by Novell, setting U taint flag.
tpm_atmel: module not supported by Novell, setting U taint flag.
hw_random hardware driver 1.0.0 loaded
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:03:00.0[D] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:03:00.0: OHCI Host Controller
ohci_hcd 0000:03:00.0: irq 11, pci mem f99fe000
ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.5-7.244-default ohci_hcd
usb usb1: SerialNumber: 0000:03:00.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:03:00.1[D] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:03:00.1: OHCI Host Controller
ohci_hcd 0000:03:00.1: irq 11, pci mem f9a00000
ohci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 2
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.5-7.244-default ohci_hcd
usb usb2: SerialNumber: 0000:03:00.1
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb 1-3: new full speed USB device using address 2
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1, 8 throttling states)
usb 1-3: Product: Virtual Keyboard and Mouse
usb 1-3: Manufacturer: American Megatrends Inc.
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.3sles9)
powernow-k8: BIOS error - no PSB
powernow: This module only works with AMD K7 CPUs
usb 2-1: new full speed USB device using address 2
usb 2-1: Product: Virtual Cdrom Device
usb 2-1: Manufacturer: American Megatrends Inc.
usb 2-2: new full speed USB device using address 3
usb 2-2: Product: Virtual Floppy Device
usb 2-2: Manufacturer: American Megatrends Inc.
usb 2-3: new full speed USB device using address 4
usb 2-3: Product: Standard USB Hub
hub 2-3:1.0: USB hub found
hub 2-3:1.0: 4 ports detected

yjyf8026

hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
st: Version 20040318, fixed bufsize 32768, s/g segs 256
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
Non-volatile memory driver v1.2
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
eth1: no IPv6 routers present
usbcore: registered new driver hiddev
Initializing USB Mass Storage driver...
input: USB HID v1.10 Keyboard [American Megatrends Inc. Virtual Keyboard and Mouse] on usb-0000:03:00.0-3
input: USB HID v1.10 Mouse [American Megatrends Inc. Virtual Keyboard and Mouse] on usb-0000:03:00.0-3
usbcore: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
scsi2 : SCSI emulation for USB Mass Storage devices
  Vendor: AMI       Model: Virtual CDROM     Rev: 1.00
  Type:   CD-ROM                             ANSI SCSI revision: 02
sr0: scsi-1 drive
Attached scsi CD-ROM sr0 at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi2, channel 0, id 0, lun 0,  type 5
USB Mass Storage device found at 2
scsi3 : SCSI emulation for USB Mass Storage devices
  Vendor: AMI       Model: Virtual Floppy    Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
eth0: no IPv6 routers present
sdb: Unit Not Ready, sense:
Current : sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sdb : READ CAPACITY failed.
sdb : status=1, message=00, host=0, driver=08
Current sd: sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sdb: assuming Write Enabled
sdb: assuming drive cache: write through
sdb: Unit Not Ready, sense:
Current : sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
bond0: no IPv6 routers present
sdb: assuming Write Enabled
sdb: assuming drive cache: write through
Attached scsi removable disk sdb at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg2 at scsi3, channel 0, id 0, lun 0,  type 0
  Vendor: AMI       Model: Virtual Floppy    Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sdc at scsi3, channel 0, id 0, lun 1
Attached scsi generic sg3 at scsi3, channel 0, id 0, lun 1,  type 0
  Vendor: AMI       Model: Virtual Floppy    Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sdd at scsi3, channel 0, id 0, lun 2
Attached scsi generic sg4 at scsi3, channel 0, id 0, lun 2,  type 0
  Vendor: AMI       Model: Virtual Floppy    Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sde at scsi3, channel 0, id 0, lun 3
Attached scsi generic sg5 at scsi3, channel 0, id 0, lun 3,  type 0
  Vendor: AMI       Model: Virtual Floppy    Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sdf at scsi3, channel 0, id 0, lun 4
Attached scsi generic sg6 at scsi3, channel 0, id 0, lun 4,  type 0
  Vendor: AMI       Model: Virtual Floppy    Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sdg at scsi3, channel 0, id 0, lun 5
Attached scsi generic sg7 at scsi3, channel 0, id 0, lun 5,  type 0
  Vendor: AMI       Model: Virtual Floppy    Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sdh at scsi3, channel 0, id 0, lun 6
Attached scsi generic sg8 at scsi3, channel 0, id 0, lun 6,  type 0
  Vendor: AMI       Model: Virtual Floppy    Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sdi at scsi3, channel 0, id 0, lun 7
Attached scsi generic sg9 at scsi3, channel 0, id 0, lun 7,  type 0
USB Mass Storage device found at 3
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
lp: driver loaded but no devices found
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
mtrr: 0xfd000000,0x800000 overlaps existing 0xfd000000,0x400000
mtrr: 0xfd000000,0x800000 overlaps existing 0xfd000000,0x400000
drivers/usb/input/hid-input.c: event field not found
irq 10: nobody cared!
Call Trace:
[<c010a66c>] __report_bad_irq+0x1c/0x70
[<c010a8fa>] do_IRQ+0x13a/0x1a0
[<c0108d38>] common_interrupt+0x18/0x20
[<c0106290>] default_idle+0x0/0x30
[<c01062b3>] default_idle+0x23/0x30
[<c0106dac>] cpu_idle+0x1c/0x40
[<c03bc65e>] start_kernel+0x29e/0x300

handlers:
[<f995fe70>] (e1000_intr+0x0/0x120 [e1000])
Disabling IRQ #10
NETDEV WATCHDOG: eth0: transmit timed out
bonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: making interface eth1 the new active one.
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
bonding: bond0: link status definitely up for interface eth0.
NET: Registered protocol family 17
spurious 8259A interrupt: IRQ7.
irq 10: nobody cared!
Call Trace:
[<c010a66c>] __report_bad_irq+0x1c/0x70
[<c010a8fa>] do_IRQ+0x13a/0x1a0
[<c0108d38>] common_interrupt+0x18/0x20
[<c01247d1>] __do_softirq+0x31/0x90
[<c0124856>] do_softirq+0x26/0x30
[<c010a8e5>] do_IRQ+0x125/0x1a0
[<c0108d38>] common_interrupt+0x18/0x20
[<c0106290>] default_idle+0x0/0x30
[<c01062b3>] default_idle+0x23/0x30
[<c0106dac>] cpu_idle+0x1c/0x40
[<c03bc65e>] start_kernel+0x29e/0x300

handlers:
[<f995fe70>] (e1000_intr+0x0/0x120 [e1000])
Disabling IRQ #10
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 1/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 2/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 3/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 4/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 5/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 6/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 7/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 8/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 9/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 10/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 11/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 12/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 13/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 14/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 15/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 16/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 17/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 18/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 19/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 20/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 21/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 22/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 23/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 24/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 25/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 26/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 27/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 28/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 29/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 30/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 31/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 32/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 33/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 34/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 35/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 36/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 37/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 38/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 39/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 40/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 41/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 42/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 43/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 44/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 45/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 46/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 47/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 48/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 49/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 50/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 51/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 52/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 53/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 54/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 55/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 56/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 57/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 58/60
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 59/60
scsi1 (0,0,0) BUSY/QUEUE FULL - probe failed

yjyf8026

多谢楼上的回帖支持！这是我看到的信息！请回复！谢谢
谢谢

yjyf8026

磁盘阵列是直接跟服务器进行连接，没有经过交换机。磁盘阵列的配置是IBM的工程师做的，应该没有什么问题。关键是现在：磁盘阵列认不到之后，重新启动服务器有时间都没有用，并且表现的很不稳定！

yjyf8026

怎么没有人回复阿？
急啊，请各位帮帮兄弟阿！

wolfop

ISP2422: PCI-X Mode 1 (66 MHz) @ 0000:05:01.0 hdma-, host#=1, fw=4.00.12 [IP]
scsi1 (0,0,0) BUSY/QUEUE FULL probing - retry 1/60
这个是错误。
你使用SUSE 9EL SP3自带的驱动还是QLOGIC的驱动的？
建议用前者。