- 论坛徽章:
- 0
|
本帖最后由 xinshouzhe 于 2011-04-29 21:37 编辑
我看相关资料说
The following baud rates are recommended for the revision B GSP:
Console: 38400
Remote: 38400
UPS: 1200
我修改之后能进入到单用户界面。另外如何修改路径到0/0/4/1，我试着用PA console 0/0/4/1 的命令去修改，是格式不对还是怎么着都不行。请大哥明示。
Configuration Menu: Enter command >
GSP Host Name: uninitialized
GSP>
CA
This command allows you to modify the local and remote modem serial port
configurations. Current configuration settings:
Local Console Serial Port bit rate: 9600 bits/s
Local Console Serial Port Flow Control: Software
Local Console Serial Port Terminal Type: vt100
Remote Console Serial Port Modem Protocol: CCITT
Remote Console Serial Port Modem bit rate: 19200 bits/s
Remote Console Serial Port Modem Flow Control: Software
Remote Console Serial Port Modem Transmit Configuration Strings: Enabled
Remote Console Serial Port Modem Presence: always connected
Do you want to modify the Local Console Serial Port settings? (Y/[N]) y
Current Local Console Serial Port bit rate: 9600 bits/s
Do you want to modify it? (Y/[N]) y
Enter Local Console Serial Port bit rate (in bits/s): 38400
New Local Console Serial Port bit rate: 38400 bits/s
Confirm? (Y/[N]): y
-> Local Console Serial Port bit rate will be updated.
Current Flow Control: Software
Do you want to modify it? (Y/[N]) n
Current Terminal Type: vt100
Do you want to modify it? (Y/[N]) n
Do you want to modify the Remote Console Serial Port Modem settings? (Y/[N]) n
Command execution may take 25 seconds.
Current Modem bit rate: 19200 bits/s
Do you want to modify it? (Y/[N]) y
y
Enter Modem bit rate (in bits/s): 38400
38400
New Modem bit rate: 38400 bits/s
Confirm? (Y/[N]): y
y
-> Modem bit rate will be updated.
Current Flow Control: Software
Do you want to modify it? (Y/[N]) n
n
Transmit Configuration Strings: Enabled
Do you want to modify it? (Y/[N]) n
n
Modem Presence: always connected
Do you want to modify it? (Y/[N]) n
n
Command execution may take 25 seconds.
-> Settings have been updated.
GSP Host Name: uninitialized
GSP> ca
CA
This command allows you to modify the local and remote modem serial port
configurations. Current configuration settings:
Local Console Serial Port bit rate: 38400 bits/s
Local Console Serial Port Flow Control: Software
Local Console Serial Port Terminal Type: vt100
Remote Console Serial Port Modem Protocol: CCITT
Remote Console Serial Port Modem bit rate: 38400 bits/s
Remote Console Serial Port Modem Flow Control: Software
Remote Console Serial Port Modem Transmit Configuration Strings: Enabled
Remote Console Serial Port Modem Presence: always connected
Do you want to modify the Local Console Serial Port settings? (Y/[N]) n
n
Do you want to modify the Remote Console Serial Port Modem settings? (Y/[N]) n
n
GSP Host Name: uninitialized
GSP> co
CO
Leaving Guardian Service Processor Command Interface and entering
Console mode. Type Ctrl-B to reactivate the GSP Command Interface.
Configuration Menu: Enter command > pa
Primary boot path: intscsib.2
0/0/1/1.2
0/0/01/01.2 (hex)
Alternate boot path: intscsia.2
0/0/2/0.2
0/0/02/0.2 (hex)
Console path: 0/0/4/0.0
0/0/04/0.0 (hex)
Keyboard path: 0/0/4/0.0
0/0/04/0.0 (hex)
Configuration Menu: Enter command > ma
---- Main Menu ---------------------------------------------------------------
Command Description
------- -----------
BOot [PRI|ALT|<path>] Boot from specified path
PAth [PRI|ALT] [<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>] Search for boot devices
COnfiguration menu Displays or sets boot values
INformation menu Displays hardware information
SERvice menu Displays service commands
DIsplay Redisplay the current menu
HElp [<menu>|<command>] Display help for menu or command
RESET Restart the system
----
Main Menu: Enter command or menu > sea
Searching for potential boot device(s)
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path# Device Path (dec) Device Path (mnem) Device Type
----- ----------------- ------------------ -----------
P0 0/0/1/1.2 intscsib.2 Random access media
P1 0/0/2/1.2 Random access media
Main Menu: Enter command or menu > bo p0
Interact with IPL (Y, N, or Cancel)?> n
Booting...
Boot IO Dependent Code (IODC) revision 1
HARD Booted.
ISL Revision A.00.43 Apr 12, 2000
ISL booting hpux
Boot
: disk(0/0/1/1.2.0.0.0.0.0;0)/stand/vmunix
9621504 + 1720320 + 19580728 start 0x1edc68
alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x7fa01000.
WARNING: Bad magic in file /stand/ioconfig (0x76657273) expected 0x21224941
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 3.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
asio0_init: unexpected SAS subsystem ID (1283)
System Console is on the Built-In Serial Interface
asio0_init: unexpected SAS subsystem ID (1283)
Entering cifs_init...
Initialization finished successfully... slot is 9
Logical volume 64, 0x3 configured as ROOT
Logical volume 64, 0x2 configured as SWAP
Logical volume 64, 0x2 configured as DUMP
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 8388608
Warning: time-of-day register time is out-of-range
Getting time from file system
Starting the STREAMS daemons-phase 1
Checking root file system.
log replay in progress
replay complete - marking super-block as CLEAN
Root check done.
Warning: time-of-day register time is out-of-range
Getting time from file system
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw fo
r CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov
8 19:24:56 PST 2000 $
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 4194304 Kbytes, lockable: 2959032 Kbytes, available: 3410108 Kbyte
s
INIT: WARNING: /etc/inittab is CORRUPT.
INIT: System being brought up SINGLE-USER !!!
INIT: SINGLE USER MODE
INIT: Running /sbin/sh
# |
|
免费注册
楼主: xinshouzhe
发表于 2011-04-29 17:03
发表于 2011-04-29 18:10