LED 解释

kimdai

RS/6000液晶显示屏上显示代码(LED)的含义

本文介绍RS/6000启动过程中机器上的液晶显示屏代码的含义。本文代码不针对具体机型。
        ---------- Dump Progress Indicator ----------
         
0c0        The dump completed successfully
0c1        The dump failed due to an I/O error.
0c2        A user-requested dump has started. You requested a dump using the SYSDUMPSTART command, a dump key sequence, or the Reset button.
       
0c3        The dump is inhibit
0c4        The dump did not complete. A partial dump was written to the dump device. There is not enough space on the dump deviceto contain the entire dump. To prevent this problem from occuring again, you must increase the size of your dumpmedia.
       
       
0c5        The dump failed to start. An unecpected error occured while the system was attempting to write to the dump media.
0c6        A dump to the secondary dump device was requested. Make the secondary dump device ready, then press CTRL-ALT-NUMPAD2.
0c7        Reserved.
0c8        The dump function is disabled. No primary dump device is configured.
0c9        A dump is in progress.
0cc        Unknown dump failure
         
         
        ---------- Diagnostics Load Progress Indicators -----------
         
c00        AIX Install/Maintenance loaded successfully.
c01        Insert the first diagnostic diskette.
c02        Diskettes inserted out of sequence.
c03        The wrong diskette is in the drive.
c04        The loading stopped with an irrecoverable error.
c05        A diskette error occurred.
c08        RAM filesystem started incorrectly.
c07        Insert the next diagnostic diskette.
c09        The diskette drive is reading or writing a diskette.
c20        An unexpected halt occured, and the system is configured to enter the kernel debug program instead of entering asystem dump.
       
c21        The 'ifconfig' command was unable to configure the network for the client network host.
c22        The 'tftp' command was unable to read client's ClientHostName.info file during a client network boot.
c24        Unable to read client's ClientHostName.info file during a client network boot.
c25        Client did not mount remote miniroot during network install.
c26        Client did not mount the /usr filesystem during the network boot.
c29        System was unable to configure the network device.
c31        Select the console display for the diagnostics. To select "No console display", set the key mode switch to normal thento Service. The diagnostic program will then load and run the diagnostics automatically.
       
c32        A direct-attached display (HFT) was selected.
c33        a TTY terminal attached to serial ports S1 or S2 was selected.
c34        A file was selected. The console messages store in a file
c40        Configuration files are been restored.
c41        Could not determine the boot type or device.
c42        Extracting data files from diskette.
c43        Diagboot cannot be accessed.
c44        Initialyzing installation database with target disk information.
c45        Cannot configure the console.
c46        Normal installation processing.
c47        Could not create a physical volume identifier (PVID) on disk.
c48        Prompting you for input.
c49        Could not create or form the JFS log.
c50        Creating rootvg volume group on target disk
c51        No paging space were found.
c52        Changing from RAM environment to disk environment.
c53        Not enough space in the /tmp directory to do a preservation installation.
c54        Installing either BOS or additionnal packages.
c55        Could not remove the specified logical volume in a preservation installation.
c56        Running user-defined customization.
c57        Failure to restore BOS.
c58        Display message to turn the key.
c59        Could not copy either device special files, device ODM, or volume group information from RAM to disk.
c61        Failed to create the boot image.
c70        Problem Mounting diagnostics CDROM disc.
c99        Diagnostics have completed. This code is only used when there is no console.
         
         
        --------Debugger Progress Indicators ----------
         
c20        Kernel debug program activated. An unexpected system halt has occured, and you have configured the system
        to enter the kernel debug program instead of performing a dump.
         
         
        ---------Built-In Self Test (Bist) Indicators---------
         
100        BIST completed successfully. Control was passed to IPL ROS.
101        BIST started following RESET
102        BIST started following Power-on Reset
103        BIST could not determine the system model number.
104        Equipment conflict. BIST could not find the CBA.
105        BIST could not read the OCS EPROM.
106        BIST detected a module error.
111        OCS stopped. BIST detected a module error.
112        A checkstop occured during BIST.
113        BIST checkstop count is greater than 1.
120        BIST starting a CRC check on the 8752 EPROM.
121        BIST detected a bad CRC in the first 32K of the OCS EPROM.
122        BIST started a CRC check on the first 32K of the OCS EPROM.
123        BIST detected a bad CRC on the OCS area of NVRAM.
124        BIST started a CRC check on the OCS area of NVRAM.
125        BIST detected a bad CRC on the time-of-day area of NVRAM.
126        BIST started a CRC check on the time-of-day area of the NVRAM.
127        BIST detected a bad CRC on the 8752 EPROM.
130        BIST presence test started.
140        BIST failed: procedure error
142        BIST failed: procedure error
143        Invalid memory configuration.
144        BIST failed; procedure error.
151        BIST started AIPGM test code.
152        BIST started DCLST test code.
153        BIST started ACLST test code.
154        BIST started AST test code.
160        Bad EPOW Signal/Power status signal
161        BIST being conducted on BUMP I/O
162        BIST being conducted on JTAG
163        BIST being conducted on Direct I/O
164        BIST being conducted on CPU
165        BIST being conducted on DCB and Memory
166        BIST being conducted on interrupts
170        BIST being conducted on 'Multi-Processor
180        BIST logout failed.
182        BIST COP bus not responding
185        A checkstop condition occured during the BIST
186        System logic-generated checkstop (Model 250 only)
187        Graphics-generated checkstop (Model 250)
195        BIST logout completed.
888        BIST did not start
         
         
        ------- Power-On Self Test -------
         
200        IPL attempted with keylock in the SECURE position.
201        IPL ROM test failed or checkstop occured (irrecoverable)
202        IPL ROM test failed or checkstop occured (irrecoverable)
203        Unexpected data storage interrupt.
204        Unexpected instruction storage interrupt.
205        Unexpected external interrupt.
206        Unexpected alignment interrupt.
207        Unexpected program interrupt.
208        Unexpected floating point unavailable interrupt.
209        Unexpected SVC interrupt.
20c        L2 cache POST error. (The display shows a solid 20c for 5 seconds
210        Unexpected SVC interrupt.
211        IPL ROM CRC comparison error (irrecoverable).
212        RAM POST memory configuration error or no memory found (irrecoverable).
213        RAM POST failure (irrecoverable).
214        Power status register failed (irrecoverable).
215        A low voltage condition is present (irrecoverable).
216        IPL ROM code being uncompressed into memory.
217        End of bootlist encountered.
218        RAM POST is looking for 1M bytes of good memory.
219        RAM POST bit map is being generated.
21c        L2 cache is not detected. (The display shows a solid 21c for 5 sec)
220        IPL control block is being initialized.
221        NVRAM CRC comparison error during AIX.
        IPL(Key Mode Switch in Normal mode).
        Reset NVRAM by reaccomplishing IPL in Service mode. For systems with an internal, direct-bus-attached(DBA)disk,IPL
        ROM attempted to perform an IPL from that disk before halting with this three-digit display value.
222        Attempting a Normal mode IPL from Standard I/O planar attached devices specified in NVRAM IPL Devices List.
223        Attempting a Normal mode IPL from SCSI attached devices specified in NVRAM IPL Devices List.
        Note: May be caused by incorrect jumper setting for external SCSI devices or by incorrect SCSI terminator.
        REFER FFC B88
224        Attempting a Normal mode restart from 9333 subsystem device specified in NVRAM device list.
225        Attempting a Normal mode IPL from IBM 7012 DBA disk attached devices specified in NVRAM IPL Devices List.
226        Attempting a Normal mode restart from Ethernet specified in NVRAM device list.
227        Attempting a Normal mode restart from Token Ring specified in NVRAM device list.
228        Attempting a Normal mode IPL from NVRAM expansion code.
229        Attempting a Normal mode IPL from NVRAM IPL Devices List; cannot IPL from any of the listed devices, or there are
        no valid entry in the Devices List.
22c        Attempting a normal mode IPL from FDDI specified in NVRAM IPL device list.
230        Attempting a Normal mode restart from adapter feature ROM specified in IPL ROM devices list.
231        Attempting a Normal mode restart from Ethernet specified in IPL ROM devices list.
232        Attempting a Normal mode IPL from Standard I/O planar attached devices specified in Rom Default Device List.
233        Attempting a Normal mode IPL from SCSI attached devices specified in IPL ROM Default Device List.
234        Attempting a Normal mode restart from 9333 subsystem device specified in IPL ROM device list.
235        Attempting a Normal mode IPL from IBM 7012 DBA disk attached devices specified in IPL ROM Default Device List.
236        Attempting a Normal mode restart from Ethernet specified in IPL ROM default devices list.
237        Attempting a Normal mode restart from Token Ring specified in IPL ROM default device list.
238        Attempting a Normal mode restart from Token Ring specified by the operator.
239        System failed to restart from the device chosen by the operator.
23c        Attempting a normal mode IPL from FDDI specified in IPL ROM device list.
240        Attempting a Service mode restart from adapter feature ROM.
241        Attempting a Normal mode IPL from devices specified in the NVRAM IPL Devices List.
242        Attempting a Service mode IPL from Standard I/O planar attached devices specified in NVRAM IPL Devices List.
243        Attempting a Service mode IPL from SCSI attached devices specified in NVRAM IPL Devices List.
244        Attempting a Service mode restart from 9333 subsystem device specified in NVRAM device list.
245        Attempting a Service mode IPL from IBM 7012 DBA disk attached devices specified in NVRAM IPL Devices List.
246        Attempting a Service mode restart from Ethernet specified in NVRAM device list.
247        Attempting a Service mode restart from Token Ring specified in NVRAM device list.
248        Attempting a Service mode IPL from NVRAM expansion code.
249        Attempting a Service mode IPL from NVRAM IPL Devices List; cannot IPL from any of the listed devices, or there areno valid entries in the Devices List.
       
24c        Attempting a service mode IPL from FDDI specified in NVRAM IPL device list.
250        Attempting a Service mode restart from adapter feature ROM specified in IPL ROM device list.
251        Attempting a Service mode restart from Ethernet specified in IPL ROM device list.
252        Attempting a Service mode IPL from standard I/O planar attached devicesspecified in ROM Default Device List.
253        Attempting a Service mode IPL from SCSI attached devices specified in IPL ROM Default Device List.
254        Attempting a Service mode restart from 9333 subsystem device specified in IPL ROM device list.
255        Attempting a Service mode IPL from IBM 7012 DBA disk'attached devices specified in IPL ROM Default Devices List.
256        Attempting a Service mode restart from Ethernet specified in IPL ROM default device list.
257        Attempting a Service mode restart from Token Ring specified in IPL ROM default device list.
258        Attempting a Service mode restart from Token Ring specified by the operator.
259        Attempting a Service mode restart from FDDI specified by the operator.
         
25c        Attempting a normal mode IPL from FDDI specified in IPL ROM device list.
260        Information is being displayed on the display console.
261        Information will be displayed on the tty terminal when the "1" key is pressed on the tty terminal keyboard.
262        A keyboard was not detected as being connected to the system's
        NOTE: Check for blown planar fuses or for a corrupted boot on disk drive
263        Attempting a Normal mode restart from adapter feature ROM specified in NVRAM device list.
269        Stalled state - the system is unable to IPL
271        Mouse port POST.
272        Tablet port POST.
277        Auto Token-Ring LANstreamer MC 32 Adapter
278        Video ROM Scan POST.
279        FDDI adapter POST.
280        3COM Ethernet POST.
281        Keyboard POST executing.
282        Parallel port POST executing
283        Serial port POST executing
284        POWER Gt1 graphadapte POST executing
285        POWER Gt3 graphadapte POST executing
286        Token Ring adapter POST executing.
287        Ethernet adapter POST executing.
288        Adapter card slots being queried.
289        GTO POST.
290        IOCC POST error (irrecoverable).
291        Standard I/O POST running.
292        SCSI POST running.
293        IBM 7012 DBA disk POST running.
294        IOCC bad TCW SIMM in slot location J being tested.
295        Graphics Display adapter POST, color or grayscale.
296        ROM scan POST.
297        System model number does not compare between OCS and ROS
        (irrecoverable). Attempting a software IPL.
298        Attempting a software IPL (warm boot).
299        IPL ROM passed control to the loaded program code.
301        Flash Utility ROM failed or checkstop occured (irrecoverable)
302        Flash Utility ROM failed or checkstop occured (irrecoverable)
302        Flash Utility ROM: User prompt, move the key to the service in order to perform an optional Flash Update. LED
        will only appear if the key switch is in the SECURE position. This signals the user that a Flash Update may be
        initiated by moving the key switch to the SERVICE position. If the key is moved to the SERVICE position,
        LED 303 will be displayed. This signals the user to press the reset button and select optional Flash Update.
303        Flash Utility ROM: User prompt, press the reset button in order to perform an optional Flash Update. LED
        only appear if the key switch is in the SECURE position. This signals the user that a Flash Update may be initiated
        by moving the key switch to the SERVICE position. If the key is moved to the SERVICE position, LED 303 will be
        displayed. This signals the user to press the reset button and select optional Flash Update.
304        Flash Utility ROM IOCC POST error (irrecoverable)
305        Flash Utility ROM standard I/O POST running.
306        Flash Utility ROM is attempting IPL from Flash Update Boot Image.
307        Flash Utility ROM system model number does not compare between OCS and ROM (irrecoverable).
308        Flash Utility ROM: IOCC TCW memory is being tested.
309        Flash Utility ROM passed control to a Flash Update Boot Image.
311        Flash Utility ROM CRC comparison error (irrecoverable).
312        Flash Utility ROM RAM POST memory configuration error or no memory found ( iirecoverable).
313        Flash Utility ROM RAM POST failure( irrecoverable).
314        Flash Utility ROM Power status register failed (irrecoverable).
315        Flash Utility ROM detected a low voltage condition.
318        Flash Utility ROM RAM POST is looking for good memory.
319        Flash Utility ROM RAM POST bit map is being generated.
322        CRC error on media Flash Image. No Flash Update performed.
323        Current Flash Image is being erased.
324        CRC error on new Flash Image after Update was performed. (Flash Image is corrupted).
325        Flash Image successful and complete.
         
500        Querying Native I/O slot.
501        Querying card in Slot 1
502        Querying card in Slot 2
503        Querying card in Slot 3
504        Querying card in Slot 4
505        Querying card in Slot 5
506        Querying card in Slot 6
507        Querying card in Slot 7
508        Querying card in Slot 8
510        Starting device configuration.
511        Device configuration completed.
512        Restoring device configuration files from media.
513        Restoring basic operating system installation files from media.
516        Contacting server during network boot
517        Mounting client remote file system during network IPL.
518        Remote mount of the root and /usr filesystems failed during network boot.
520        Bus configuration running.
521        /etc/init invoked cfgmgr with invalid options; /etc/init has been corrupted or incorrectly modified
        (irrecoverable error).
522        The configuration manager has been invoked with conflicting options (irrecoverable error).
523        The configuration manager is unable to access the ODM database (irrecoverable error).
524        The configuration manager is unable to access the config rules object in the ODM database (irrecoverable error).
525        The configuration manager is unable to get data from a customized device object in the ODM database
        (irrecoverable error).
526        The configuration manager is unable to get data from a customized device driver objet in the ODM database
        (irrecoverable error).
527        The configuration manager was invoked with the phase 1 flag; running phase 1 flag; running phase 1 at this point
        is not permitted (irrecoverable error).
528        The configuration manager cannot find sequence rule, or no program was specified in the ODM database
        (irrecoverable error).
529        The configuration manager is unable to update ODM data
        (irrecoverable error).
530        The program "savebase" returned an error.
531        The configuration manager is unable to access PdAt object class
        (irrecoverable eroor)
532        There is not enough memory to continue (malloc failure);
        irrecoverable error.
533        The configuration manager could not find a configure method for a device.
534        The configuration manager is unable to aquire database lock. irrecoverable error.
536        The configuration manager encountered more than one sequence rule specified in the same phase. (irrecoverable error).
537        The configuration manager encountered an error when invoking the program in the sequence rule.
538        The configuration manager is going to invoke a configuration
539        The configuration method has terminated, and control has returned to the configuration manager.
551        IPL Varyon is running
         
552        IPL Varyon failed.
553        IPL phase 1 is complete.
554        Unable to define NFS swap device during network boot
555        Unable to define NFS swap device during network boot
556        Logical Volume Manager encountered error during IPL varyon.
557        The root filesystem will not mount.
558        There is not enough memory to continue the IPL.
559        Less than 2MB of good memory are available to load the AIX kernel.
570        Virtual SCSI devices being configured.
571        HIPPI common function device driver being configured.
572        HIPPI IPI-3 master transport driver being configured.
573        HIPPI IPI-3 slave transport driver being configured.
574        HIPPI IPI-3 transport services user interface device driver being configured.
576        Generic async device driver being configured.
577        Generic SCSI device driver being configured.
578        Generic commo device driver being configured.
579        Device driver being configured for a generic device.
580        HIPPI TCPIP network interface driver being configured.
581        Configuring TCP/IP.
582        Configuring token ring data link control.
583        Configuring an Ethernet data link control.
584        Configuring an IEEE ethernet data link control.
585        Configuring an SDLC MPQP data link control.
586        Configuring a QLLC X.25 data link control.
587        Configuring NETBIOS.
588        Configuring a Bisync Read-Write (BSCRW).
589        SCSI target mode device being configured.
590        Diskless remote paging device being configured.
591        Configuring an LVM device driver
592        Configuring an HFT device driver
593        Configuring SNA device drivers.
594        Asynchronous I/O being defined or configured.
595        X.31 pseudo device being configured.
596        SNA DLC/LAPE pseudo device being configured.
597        OCS software being configured.
598        OCS hosts being configured during system reboot.
599        Configuring FDDI data link control.
5c0        Streams-based hardware drive being configured.
5c1        Streams-based X.25 protocol being configured.
5c2        Streams-based X.25 COMIO emulator driver being configured.
5c3        Streams-based X.25 TCP/IP interface driver being configured.
5c4        FCS adapter device driver being configured.
5c5        SCB network device driver for FCS is being configured.
5c6        AIX SNA channel being configured.
600        Starting network boot portion of /sbin/rs.boot
602        Configuring network parent devices.
603        /usr/lib/methods/defsys
        /usr/lib/methods/cggsys, or
        /usr/lib/methods/cggbus failed.
604        Configuring physical network boot device.
605        Configuring physical network boot device failed.
606        Running /usr/sbin/ifconfig on logical network boot device.
607        /usr/sbin/ifconfig failed.
608        Attempting to retrieve the client.info file with tftp. Note that a flashing 608 indicates multiple attempts
        to retrieve the client_info file are occuring.
609        The client.info file does not exist or it is zero length.
610        Attempting remote mount of NFS file system
611        Remote mount of the NFS filesystem failed.
612        Accessing remote files; unconfiguring network boot device.
614        Configuring local paging devices.
615        Configuring of a local paging device failed.
616        Converting from diskette to dataless configuration.
617        Diskless to dataless configuration failed.
618        Configuring remote (NFS) paging devices.
619        Configuration of a remote (NFS) paging device failed.
620        Updating special device files and ODM in permanent filesystem with data from boot RAM filesystem.
622        Boot process configuring for operating system installation.
         
650        IBM SCSD disk drive drive being configured
700        Progress indicator. A 1.1GB 8-bit SCSI disk drive being identified or configured.
701        Progress indicator. A 1.1GB 16-bit SCSI SE disk drive being identified or configured.
702        Progress indicator. A 1.1GB 16-bit SCSI differential disk drive being identified or configured.
703        Progress indicator. A 2.2GB 8-bit SCSI disk drive being identified or configured.
704        Progress indicator. A 2.2GB 16-bit SCSI SE disk drive being identified or configured.
705        The configuration method for the 2.2GB 16-bit differential SCSI disk drive is being run. If a irrecoverableerror occurs, the system halts. identified or configured.
       
706        Progress indicator. A 4.5GB 16-bit SE SCSI disk drive is being identified or configured.
707        Progress indicator. A 4.5GB 16-bit differential SCSI drive is being identified or configured.
708        Progress indicator: A L2 cache is being identified or configured.
710        POWER GXT150M graphics adapterbeing ientifyied or configured.
711        Unknown adapter being identified or configured.
712        Graphics slot bus configuration is executing.
713        The IBM ARTIC960 device is being configured.
714        A video capture adapter is being configured.
715        The Ultimedia Services audio adapter is being configured. This LED displays briefly on the panel.
720        Unknown read/write optical drive type being configured.
721        Unknown disk or SCSI device being identified or configured.
722        Unknown disk being identified or configured.
723        Unknown CDROM being identified or configured.
724        Unknown tape drive being identified or configured.
725        Unknown display being identified or configured.
726        Unknown input device being idenor configured
727        Unknown adync device being idenor configured