630机器，AIX5.2报错

tinkle_boy

前两天paging space空间被占满（原因还没有查明），直接按按钮关机，启动后就有这个报错，在diag里面进行log repair action后警报灯熄灭。但是现在每天早上都能收到警报mail，警报灯也亮起，mail发出的时间基本相同，请各位帮我看看。

diag中的信息：
The Service Request Number(s)/Probable Cause(s)
(causes are listed in descending order of probability):

  651-880: The CEC or SPCN reported an error. Report the SRN and the following
           reference and physical location codes to your service provider.
           Error log information:
                 Date: Fri Feb 27 08:40:23 BEIST 2004
                 Sequence number: 317
                 Label: SCAN_ERROR_CHRP
    Ref. Code: B1004699 FRU: n/a              n/a


mail信息：
A PROBLEM WAS DETECTED ON Mon Mar  1 04:05:42 BEIST 2004                  801014

The Service Request Number(s)/Probable Cause(s)
(causes are listed in descending order of probability):

  651-880: The CEC or SPCN reported an error. Report the SRN and the following
           reference and physical location codes to your service provider.
           Error log information:
                 Date: Fri Feb 27 08:40:23 BEIST 2004
                 Sequence number: 317
                 Label: SCAN_ERROR_CHRP
    Ref. Code: B1004699 FRU: n/a              n/a

onbaby

Service processor firmware:
This is usually an indication of a problem in the communication path between the
HMC and the service processor. It may only be an informational message.
If the managed system is down, go to the service processor error log and find the
error log entry containing B1xx 4699. Look at the first two bytes of word 13 of the
detailed entry information.
做一下diag看看有没有更详细的描述,errpt 有相应的错误信息吗?

lljj

查查B1004699说的是什么啊？

我觉得和你pgsp满了没有直接联系！

tinkle_boy

原帖由 "onbaby" 发表：
Service processor firmware:
This is usually an indication of a problem in the communication path between the
HMC and the service processor. It may only be an informational message.
If the managed s..........

diag里面没有其他东西了，errpt也没有特别的，警报灯重新亮起时这两个都没有相应记录，只收到mail。
搜索了一下B1004699，只有关于AS400的内容。好像跟我这里没关系。现在问题时每天都会报警，系统运行正常。郁闷ing！

onbaby

是B1xx 4699:
If the managed system is running, look at the AIX error log entry containing B1xx
4699. This is a "SCAN_ERROR_CHRP" error with an identifier of BFE4C025. In
the detail data, find the string "B1xx 4699". (If present, it will be at byte 60 of the
detail data.) Go forward 8 bytes after the ²B1² to byte 68 and look at bytes 68 and
69.
Perform the following actions based on the following values of bytes 68 and 69
from the AIX error log entry, or on the first two bytes of word 13 from the service
processor error log entry:
A800: This indicates an HMC/service processor initialization failure.
Actions:
1. Check for system firmware updates.
2. Replace the CEC backplane, location: U0.1-P1.
A801: This indicates an HMC wrap failure.
Actions:
1. Replace the CEC backplane, location: U0.1-P1.
A806: This indicates a loss of the surveillance heartbeat between the HMC
and the service processor.
Actions:
1. Make sure that the HMC is booted and operational.
2. Check the serial cables that go from the HMC to the CEC
backplane, location: U0.1-P1.
If there are no other error codes or indications of a problem, the A806
(loss of surveillance heartbeat) was a temporary condition and has been
resolved; the B1xx4699 code is then an informational message only.
If the problem persists:
1. Check the serial cables connecting the HMC to the CEC backplane, location:
U0.1-P1.
2. Run diagnostics on the serial port on the HMC.
3. Run diagnostics on the serial ports on the service processor.
Values of A009 and A719 of bytes 68 and 69 in the AIX error log entry or the first
two bytes of word 13 in the service processor error log entry are also
informational entries:
A009: The white button on the operator panel was used to power off the
system.
A719: Primary power failed; the system switched to battery backup power.
A value of A205 indicates that the machine type and model fields are not valid in
the VPD module on the operator panel. Do the following:
A205: Machine and model fields are not valid in the VPD module. Obtain a
new operator panel. Do not swap the old VPD module onto the new
operator panel. Call service support for instructions on how to write the
machine type and model into the new VPD module.
For all other values of bytes 68 and 69, or the first two bytes of word 13, do the
following:
1. Check for system firmware updates.
2. Reset the service processor by activating the pinhole reset switch on the
operator panel.
3. Call service support.
如果问题不能解决,机器又在保修期内,那只好叫IBM了.

camp

太可怕了，都要动CEC了。