论坛徽章:: 0

电梯直达

1楼 [收藏(0)] [报告]

发表于 2008-03-03 17:02 |只看该作者 |倒序浏览

系统启动时报错:
************* SYSTEM ALERT **************
SYSTEM NAME: uninitialized
ALERT LEVEL: 8 = Boot Possible, performance impaired
REASON FOR ALERT
SOURCE: 6 = platform
SOURCE DETAIL: 6 = service processor SOURCE ID: 0
PROBLEM DETAIL: 1 = selftest result
LEDs:  RUN    ATTENTION    FAULT    REMOTE    POWER
   FLASH FLASH       ON       OFF       ON
LED State: Boot Failed.  Running non-OS code.  Non-critical error detected.
Check Chassis and Console Logs for error messages.
0x7010028166002030 0B0003FF DD0C0045 - type 14 = Problem Detail
0x4810028166002030 67720000 7361734D - type  9 = ASCII Message       sasMgr
0x4810028166002030 78632E43 4C4F4765 - type  9 = ASCII Message       LOGexc.C
0x7010028166002030 00000000 00002F35 - type 14 = Problem Detail
0x70100A8166002030 0003292E 2F2A2000 - type 14 = Problem Detail
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
->Choice:a
*****************************************
Firmware Version  43.22
********** VIRTUAL FRONT PANEL **********
System Boot detected
*****************************************
LEDs:  RUN    ATTENTION    FAULT    REMOTE    POWER
   FLASH FLASH       ON       OFF       ON
LED State: Boot Failed.  Running non-OS code.  Non-critical error detected.
Check Chassis and Console Logs for error messages.
platform                config                   626F
*****************************************
************ EARLY BOOT VFP *************
End of early boot detected
*****************************************
------------------------------------------------------------------------------
(c) Copyright 1995-2002, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
  Processor Speed          State          CoProcessor State  Cache Size
  Number                                     State             Inst Data
  ---------  -------- ---------------------  -----------------  ------------
   0    750  MHz Active                Functional       750 KB 1.5 MB
   2    750  MHz Idle                Functional       750 KB 1.5 MB
  Central Bus Speed (in MHz)  :       133
  Available Memory          : 1048576  KB
  Good Memory Required       :    36592  KB
Primary boot path: 0/0/2/0.0
Alternate boot path:  0/0/2/0.2
Console path:       0/0/4/1.0
Keyboard path:       0/0/4/0.0
Processor is booting from first available device.
To discontinue, press any key within 10 seconds.
Information Menu: Enter command > bo
Interact with IPL (Y, N, or Cancel)?> n
Booting...
Boot IO Dependent Code (IODC) revision 1
************* SYSTEM ALERT **************
SYSTEM NAME: uninitialized
DATE: 02/25/2008 TIME: 01:07:44
ALERT LEVEL: 6 = Boot possible, pending failure - action required
REASON FOR ALERT
SOURCE: 8 = I/O
SOURCE DETAIL: 6 = disk SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail

GSP卡错误日志:
Log Entry # 0 :
SYSTEM NAME: uninitialized
ALERT LEVEL: 8 = Boot Possible, performance impaired
SOURCE: 6 = platform
SOURCE DETAIL: 6 = service processor SOURCE ID: 0
PROBLEM DETAIL: 1 = selftest result
CALLER ACTIVITY: 2 = operation STATUS: 0
CALLER SUBACTIVITY: 03 = console
REPORTING ENTITY TYPE: 1 = service processor REPORTING ENTITY ID: 00
0x7010028166002030 0B0003FF DD0C0045 type 14 = Problem Detail
0x4810028166002030 67720000 7361734D type  9 = ASCII Message       sasMgr
0x4810028166002030 78632E43 4C4F4765 type  9 = ASCII Message       LOGexc.C
0x7010028166002030 00000000 00002F35 type 14 = Problem Detail
0x70100A8166002030 0003292E 2F2A2000 type 14 = Problem Detail
Type CR for next entry, Q CR to quit.

Log Entry # 1 :
SYSTEM NAME: uninitialized
DATE: 02/22/2008 TIME: 09:14:27
ALERT LEVEL: 15 = Fatal hardware or configuration problem prevents operation
SOURCE: 8 = I/O
SOURCE DETAIL: 6 = disk SOURCE ID: 0
PROBLEM DETAIL: 3 = functional failure
CALLER ACTIVITY: 1 = test STATUS: 0
CALLER SUBACTIVITY: 48 = implementation dependent
REPORTING ENTITY TYPE: 0 = system firmware REPORTING ENTITY ID: 00
0x000000F386001480 00000000 00000000 type  0 = Data Field Unused
0x580008F386001480 00006C01 16090E1B type 11 = Timestamp 02/22/2008 09:14:27

用光盘引导:
Main Menu: Enter command or menu > sea
Searching for potential boot device(s)
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).

                                                                        IODC
Path#  Device Path (dec)  Device Path (mnem)  Device Type             Rev
-----  -----------------  ------------------  -----------             ----
P0    0/0/2/0.0       intscsia.0       Random access media    1
P1    0/0/2/1.0                            Random access media    1

Main Menu: Enter command or menu > bo p1
Interact with IPL (Y, N, or Cancel)?> n
Booting...
Boot IO Dependent Code (IODC) revision 1

HARD Booted.
ISL Revision A.00.43  Apr 12, 2000
ISL booting  hpux (;0):INSTALL
Boot
: disk(0/0/2/1.0.0.0.0.0.0;0):WINSTALL
8941568 + 1642496 + 2596176 start 0x1fef68

alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x3fb01000
下面这个是在MP下的错误信息！！本人在线等

0xf8e000301100ef00 00000000 0000ef00
type 31 = legacy PA HEX classis-code.

emc-hpux

白手起家

论坛徽章:: 0

2楼 [报告]

发表于 2008-03-03 17:11 |只看该作者

下面是同时出现的其他部分 ’System Alert’ 消息:
ALERT LEVEL: 12 = Software failure REASON FOR ALERT SOURCE: 1 = processor SOURCE DETAIL: 1 = processor general SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail LEDs: RUN ATTENTION FAULT REMOTE POWER ON FLASH OFF OFF ON LED State: There was a system interruption that did nottake the system down. Check Chassis and Console Logs for error messages. 0xF8E000C01100B800 00000000 0000B800 - type 31 = legacy PA HEX chassis-code 0x58E008C01100B800 00006404 1A0F2932 - type 11 = Timestamp A: ack read of this entry - X: Disable all future alert messages Anything else skip redisplay the log entry
-> Choice:a
这个也是