ipmp配置后的问题

liar222

配置ipmp过程如下：\r\n机型：v445\r\n修改/etc/hosts:\r\n192.168.1.6         PAS-01-A\r\n192.168.1.112     PAS-01-A-bge0-test\r\n192.168.1.212     PAS-01-A-bge1-test \r\n\r\n修改/etc/hostname.bge0\r\nPAS-01-A netmask + broadcast + group sc_ipmp0 up addif PAS-01-A-bge0-test deprecated -failover netmask + broadcast + up\r\n\r\n修改/etc/hostname.bge1\r\nPAS-01-A-bge1-test netmask + broadcast + deprecated group sc_ipmp0 -failover standby up\r\n\r\n编辑/etc/defaultrouter:\r\n内容为网关地址192.168.1.101（始终在线）能够ping 通。\r\n\r\n修改local-mac-address :\r\n#eeprom local-mac-address?=true\r\n \r\n\r\n重启机器:\r\n#reboot\r\n\r\n\r\n\r\n重启机器后，发现bge0的test ip192.168.1.112已经被加载在bge0：1上，但是bge1的ip仍然为0.0.0.0，且没有up\r\n想问问有没有碰到过这种现象的，望告知原因，谢谢！

liar222

配好后看网卡配置如下：bge1没有up，且ip也没有配上，问题出在哪里呢？\r\n# hostname\r\nPAS-01-A\r\n# ifconfig -a\r\nlo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1\r\n        inet 127.0.0.1 netmask ff000000 \r\nbge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2\r\n        inet 192.168.1.5 netmask ffffff00 broadcast 192.168.1.255\r\n        groupname sc_ipmp0\r\n        ether 0:14:4f:a0:d0:f2 \r\nbge0:1: flags=9040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER> mtu 1500 index 2\r\n        inet 192.168.1.112 netmask ffffff00 broadcast 192.168.1.255\r\nbge1: flags=1000842<BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3\r\n        inet 0.0.0.0 netmask 0 \r\n        ether 0:14:4f:a0:d0:f3

westlife521

if_mpadm -d bge0 \r\n再ifconfig -a\r\n看一下

liar222

解决了，把原来的/etc/hostname.bge1删掉，原样在创建一个，重启，成功！\r\n真是奇怪了，两个文件是一摸一样的－－－－我在删除旧的文件之前把内容复制出来然后完全粘贴到新的文件中÷\r\n想知道原因……

westlife521

现在ifconfig -a 贴出来看一下

liar222

现在的网络配置输出：\r\n\r\n# hostname\r\nPAS-01-A\r\n# ifconfig -a\r\nlo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1\r\n        inet 127.0.0.1 netmask ff000000 \r\nbge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2\r\n        inet 192.168.1.5 netmask ffffff00 broadcast 192.168.1.255\r\n        groupname sc_ipmp0\r\n        ether 0:14:4f:a0:d0:f2 \r\nbge0:1: flags=9040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER> mtu 1500 index 2\r\n        inet 192.168.1.112 netmask ffffff00 broadcast 192.168.1.255\r\nbge1: flags=69040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,STANDBY,INACTIVE> mtu 1500 index 3\r\n        inet 192.168.1.212 netmask ffffff00 broadcast 192.168.1.255\r\n        groupname sc_ipmp0\r\n        ether 0:14:4f:a0:d0:f3 \r\n#

tzpi2000

是否在于重新启动  或者以前的里面有空格