重灌c2621 ios后出现的异常现象

kymjxhm

route(config)#interface ?\r\n  Async              Async interface\r\n  BVI                Bridge-Group Virtual Interface\r\n  Dialer             Dialer interface\r\n  Group-Async        Async Group interface\r\n  Lex                Lex interface\r\n  Loopback           Loopback interface\r\n  Null               Null interface\r\n  Port-channel       Ethernet Channel of interfaces\r\n  Tunnel             Tunnel interface\r\n  Virtual-Template   Virtual Template interface\r\n  Virtual-TokenRing  Virtual TokenRing\r\n\r\nroute(config)#interface\r\n大家看看我的这台路由器怎么没了fastEthernet\r\n我也重灌了ios

calay

肯定是版本错了,你惯了一个不支持FastEthernet的IOS

kymjxhm

已经重灌了IOS\r\n但无法启动停在Compiled Mon 29-Nov-99 15:15 by kpma状态\r\n跟这些设置有关吗：\r\ndo you wish to change the configuration? y/n  [n]:  y\r\nenable  \"diagnostic mode\"? y/n  [n]:\r\nenable  \"use net in IP bcast address\"? y/n  [n]:\r\ndisable \"load rom after netboot fails\"? y/n  [n]:\r\nenable  \"use all zero broadcast\"? y/n  [n]:\r\ndisable \"break/abort has effect\"? y/n  [n]:\r\nenable  \"ignore system config info\"? y/n  [n]:\r\nchange console baud rate? y/n  [n]:\r\nchange the boot characteristics? y/n  [n]:\r\n且confreg 已设为 0x2012

zhaoshan

do you wish to change the configuration? y/n [n]: y \r\nenable \"diagnostic mode\"? y/n [n]: y\r\nenable \"use net in IP bcast address\"? y/n [n]:n \r\ndisable \"load rom after netboot fails\"? y/n [n]: n\r\nenable \"use all zero broadcast\"? y/n [n]: n\r\ndisable \"break/abort has effect\"? y/n [n]: n\r\nenable \"ignore system config info\"? y/n [n]:n \r\nchange console baud rate? y/n [n]: n\r\nchange the boot characteristics? y/n [n]:n

kymjxhm

按楼上所说已做了相应设置，但问题依旧\r\n#dir\r\n出错\r\n但在COMMON下\r\ndir flash:\r\nc2600-is-mz.120-8

zhaoshan

这个c2600-is-mz.120-8符合你的硬件配置吗？

kymjxhm

是的符合\r\n是我所备份的

kymjxhm

本来我是想升级到IP PLUS，\r\n结果提示内存不够，\r\n再恢复就出现以上问题，\r\n希望大家帮帮我，\r\n几天了，\r\n我都搞得焦头烂额的！\r\n谢谢！

我爱臭豆腐

你过去和现在是什么版本啊?你是怎么升级的?另外show ver 看看你认出什么接口来了.

kymjxhm

Router#show ver\r\nCisco Internetwork Operating System Software\r\nIOS (tm) C2600 Software (C2600-IS-M), Version 12.0(, RELEASE SOFTWARE (fc1)\r\nCopyright (c) 1986-1999 by cisco Systems, Inc.\r\nCompiled Mon 29-Nov-99 15:15 by kpma\r\nImage text-base: 0x80008088, data-base: 0x808E63A0\r\n\r\nROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)\r\n\r\nRouter uptime is 0 minutes\r\nSystem restarted by power-on\r\nSystem image file is \"flash:c2600-is-mz.120-8.bin\"\r\n\r\ncisco 2600 (MPC860) processor (revision 0x100) with 26624K/6144K bytes of memory\r\n.\r\nProcessor board ID JAD0626CB7D (2994896540)\r\nM860 processor: part number 5, mask 2\r\nBridging software.\r\nX.25 software, Version 3.0.0.\r\n32K bytes of non-volatile configuration memory.\r\n\r\nConfiguration register is 0x2102