回复 1楼 allonsun 的帖子

Configuration register is 0x2102\r\nRouter> !--- The router was just powercycled and during bootup a \r\n!--- break sequence was sent to the router.\r\n!\r\n\r\n*** System received an abort due to Break Key ***\r\n\r\nsignal= 0x3, code= 0x500, context= 0x813ac158\r\nPC = 0x802d0b60, Vector = 0x500, SP = 0x80006030\r\nrommon 1 > confreg 0x2142\r\n\r\n\r\nYou must reset or power cycle for new config to take effect\r\nrommon 2 > reset\r\n\r\n\r\nSystem Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)\r\nCopyright (c) 1999 by cisco Systems, Inc.\r\nTAC:Home:SW:IOS:Specials for info\r\nC2600 platform with 32768 Kbytes of main memory\r\n\r\n\r\nprogram load complete, entry point: 0x80008000, size: 0x6fdb4c\r\n\r\nSelf decompressing the image : ###############################\r\n##############################################################\r\n##############################################################\r\n##############################################################\r\n############################### [OK]\r\n\r\n\r\n Restricted Rights Legend\r\n\r\nUse, duplication, or disclosure by the Government is\r\nsubject to restrictions as set forth in subparagraph\r\n(c) of the Commercial Computer Software - Restricted\r\nRights clause at FAR sec. 52.227-19 and subparagraph\r\n(c) (1) (ii) of the Rights in Technical Data and Computer\r\nSoftware clause at DFARS sec. 252.227-7013.\r\n\r\n cisco Systems, Inc.\r\n 170 West Tasman Drive\r\n San Jose, California 95134-1706\r\n\r\nCisco Internetwork Operating System Software\r\nIOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)\r\nCopyright (c) 1986-1999 by cisco Systems, Inc.\r\nCompiled Tue 07-Dec-99 02:21 by phanguye\r\nImage text-base: 0x80008088, data-base: 0x80C524F8\r\n\r\ncisco 2611 (MPC860) processor (revision 0x202) with 26624K/6144K bytes of memory.\r\nProcessor board ID JAB031202NK (3878188963)\r\nM860 processor: part number 0, mask 49\r\nBridging software.\r\nX.25 software, Version 3.0.0.\r\nBasic Rate ISDN software, Version 1.1.\r\n2 Ethernet/IEEE 802.3 interface(s)\r\n2 Serial(sync/async) network interface(s)\r\n1 ISDN Basic Rate interface(s)\r\n32K bytes of non-volatile configuration memory.\r\n8192K bytes of processor board System flash partition 1 (Read/Write)\r\n8192K bytes of processor board System flash partition 2 (Read/Write)\r\n\r\n\r\n --- System Configuration Dialog ---\r\n\r\nWould you like to enter the initial configuration dialog? [yes/no]: n\r\n\r\nPress RETURN to get started!\r\n\r\n00:00:19: %LINK-3-UPDOWN: Interface BRI0/0, changed state to up\r\n00:00:19: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up\r\n00:00:19: %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up\r\n00:00:19: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down\r\n00:00:19: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down\r\n00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0, changed state to down\r\n00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to up\r\nRouter>\r\n00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, changed state to up\r\n00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down\r\n00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to down\r\n00:00:50: %SYS-5-RESTART: System restarted --\r\nCisco Internetwork Operating System Software\r\nIOS (tm) C2600 Software (C2600-IS-M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)\r\nCopyright (c) 1986-1999 by cisco Systems, Inc.\r\nCompiled Tue 07-Dec-99 02:21 by phanguye\r\n00:00:50: %LINK-5-CHANGED: Interface BRI0/0, changed state to administratively down\r\n00:00:52: %LINK-5-CHANGED: Interface Ethernet0/0, changed state to administratively down\r\n00:00:52: %LINK-5-CHANGED: Interface Serial0/0, changed state to administratively down\r\n00:00:52: %LINK-5-CHANGED: Interface Ethernet0/1, changed state to administratively down\r\n00:00:52: %LINK-5-CHANGED: Interface Serial0/1, changed state to administratively down\r\n00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, changed state to down\r\n00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, changed state to down\r\nRouter>\r\nRouter>en\r\nRouter#copy start run\r\nDestination filename [running-config]?\r\n1324 bytes copied in 2.35 secs (662 bytes/sec)\r\nRouter#\r\n00:01:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1, changed state to down\r\n00:01:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:2, changed state to down\r\nRouter#conf t\r\nEnter configuration commands, one per line. End with CNTL/Z.\r\nRouter(config)#enable secret cisco\r\nRouter(config)#^Z