- 论坛徽章:
- 0
|
本帖最后由 lbseraph 于 2013-01-26 10:05 编辑
Event Time..........: Thu Jan 24 17:44:49 2013
Severity............: MAJORWARNING
Monitor.............: armmon
Event #.............: 16
System..............: xywg2
Summary:
Disk Array at hardware path :
One or more of the batteries in the Controller in slot Y have
failed.
Description of Error:
This event message is displayed when there is not enough electrical
charge on one of the battery packs in the indicated controller to
maintain NVRAM.
Each controller contains two battery packs. If both battery packs
cannot provide the minimum protection for the NVRAM, then the
controller refuses to boot. Without NVRAM protection, all user data
may be lost. When a battery pack has been fully charged and then
enters the warning state, it may last only about an hour or less if
called upon to protect NVRAM.
The following battery behavior should be noted:
1. In order to assess the reliability of the batteries, periodic
checks are made by the controller firmware.
2. In addition to other tests, each battery is deliberately discharged
occasionally and then recharged, to make sure it can be relied
upon. These test conditions are not reported as battery warning or
battery dead conditions.
3. To avoid leaving NVRAM unprotected, if a controller has one dead
battery pack, the testing process skips the discharge testing of
its other battery.
4. A discharged battery should normally recharge promptly when power
is supplied to the disk array. Therefore, a battery warning or
battery dead condition generally goes away without any operator
intervention required.
5. Any such condition that persists for longer than about an hour
should be acted upon, or an otherwise functional controller (one
that has both battery packs dead or missing) will not boot.
6. A non-functioning controller cannot report the status of its
batteries. The other controller (if present) reports the condition
(dead or missing).
Possible causes include:
1. Power has never been applied, and the batteries need to be charged.
2. Power has been off so long that the charge in the batteries has been
used up.
Probable Cause / Recommended Action:
Replace both batteries (replace them one at a time, to preserve NVRAM)
in the indicated controller.
Additional Event Data:
System IP Address...: 192.1.1.2
System IP Address...: 133.71.5.2
Event Id............: 0x5101029100000001
Monitor Version.....: B.01.01
Event Class.........: I/O
Client Configuration File...........:
/var/stm/config/tools/monitor/default_armmon.clcfg
Client Configuration File Version...: A.01.01
Qualification criteria met.
Number of events..: 1
Associated OS error log entry id(s):
None
Additional System Data:
System Model Number.............: 9000/800
EMS Version.....................: A.03.20
STM Version.....................: A.34.00
Latest information on this event:
http://docs.hp.com/hpux/content/hardware/ems/armmon.htm#16
v-v-v-v-v-v-v-v-v-v-v-v-v D E T A I L S v-v-v-v-v-v-v-v-v-v-v-v-v
Product/Device Data:
Logger ID.........: (not available/applicable)
Product Identifier: (not available/applicable)
Product Qualifier.: (not available/applicable)
SCSI Target ID....: (not available/applicable)
SCSI LUN..........: (not available/applicable)
>---------- End Event Monitoring Service Event Notification ----------<
# uname -a
HP-UX B.11.00 U 9000/800 190460591 unlimited-user license
机器为老的k360的机器，现在液晶板上显示repalce battery 提示，大家有没有遇到过啊 ？
是什么坏了，这小机上有电池吗？？
这种情况怎么解决。。 |
|
免费注册
发表于 2013-01-25 08:52
发表于 2013-01-26 10:16