为什么网卡必须在转换运行级别以后才能通？

chenyx

@ulovko这个情况确实没见过

jodgen

wenhq 发表于 2013-05-15 19:22
伙计把dmesg贴一下，机器重启过程的日志能提供一下不？感觉太奇怪了。道理上不应该这样。

谢谢，我是菜鸟，不明白重启过程的日志该到哪里看，百度了下dmesg就是启动日志唉。。。

[root@Webquery ~]# dmesg
Linux version 2.6.18-128.el5PAE (mockbuild@hs20-bc1-5.build.redhat.com) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-44)) #1 SMP Wed Dec 17 12:02:33 EST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
BIOS-e820: 000000000009d400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bf7a0000 (usable)
BIOS-e820: 00000000bf7a0000 - 00000000bf7ad000 (ACPI data)
BIOS-e820: 00000000bf7ad000 - 00000000bf7ae000 (ACPI NVS)
BIOS-e820: 00000000bf7ae000 - 00000000bf7ff000 (reserved)
BIOS-e820: 00000000bf800000 - 00000000c0000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
4224MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f6e20
Memory for crash kernel (0x0 to 0x0) notwithin permissible range
disabling kdump
NX (Execute Disable) protection: active
On node 0 totalpages: 1310720
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 1081344 pages, LIFO batch:31
DMI 2.6 present.
Using APIC driver default
ACPI: RSDP (v002 PTLTD                                 ) @ 0x000f6df0
ACPI: XSDT (v001 HP     ProLiant 0x06040000  LTP 0x00000000) @ 0xbf7a8407
ACPI: FADT (v003 HP     LYNNFLD  0x06040000 PTL  0x00000002) @ 0xbf7ac6ad
ACPI: TCPA (v001 HP     ProLiant 0x06040000 LOHR 0x0000005a) @ 0xbf7ac7a1
ACPI: SSDT (v001  INTEL PPM RCM  0x80000001 INTL 0x20061109) @ 0xbf7a03ab
ACPI: SPMI (v005 HP     ProLiant 0x06040000 PTL  0x00000001) @ 0xbf7ac7f7
ACPI: EINJ (v001 HP     ProLiant 0x06040000 PTL  0x00000001) @ 0xbf7ac837
ACPI: HEST (v001 HP     ProLiant 0x06040000 PTL  0x00000001) @ 0xbf7ac9e7
ACPI: BERT (v001 HP     ProLiant 0x06040000 PTL  0x00000001) @ 0xbf7acb0f
ACPI: SSDT (v001 HP     ProLiant 0x06040000 INTL 0x20050624) @ 0xbf7acb3f
ACPI: ERST (v001 HP     ProLiant 0x06040000 PTL  0x00000001) @ 0xbf7acc20
ACPI: MADT (v001 HP     ProLiant 0x06040000  LTP 0x00000000) @ 0xbf7ace90
ACPI: MCFG (v001 HP     ProLiant 0x06040000  LTP 0x00000000) @ 0xbf7acf14
ACPI: HPET (v001 PTLTD  HPETTBL  0x06040000  LTP 0x00000001) @ 0xbf7acf50
ACPI: BOOT (v001 HP     ProLiant 0x06040000  LTP 0x00000001) @ 0xbf7acf88
ACPI: SPCR (v001 HP     ProLiant 0x06040000 PTL  0x00000001) @ 0xbf7acfb0
ACPI: DSDT (v001 HP     ProLiant 0x06040000 MSFT 0x03000000) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 7:14 APIC version 21
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled)
Processor #2 7:14 APIC version 21
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)
Processor #4 7:14 APIC version 21
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled)
Processor #6 7:14 APIC version 21
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x8086a701 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
Detected 2394.089 MHz processor.
Built 1 zonelists.  Total pages: 1310720
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0752000 soft=c0732000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 4135308k/5242880k available (2119k kernel code, 49140k reserved, 879k data, 228k init, 3268224k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0, 0, 0, 0, 0, 0
hpet0: 8 64-bit timers, 14318180 Hz
Using HPET for base-timer
Calibrating delay using timer specific routine.. 4790.97 BogoMIPS (lpj=2395489)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 28100000 00000000 00000000 0098e3fd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 28100000 00000000 00000000 0098e3fd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 28100000 00000000 00000940 0098e3fd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Xeon(R) CPU           X3430  @ 2.40GHz stepping 05
SMP alternatives: switching to SMP code
Booting processor 1/2 eip 3000
CPU 1 irqstacks, hard=c0753000 soft=c0733000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4787.93 BogoMIPS (lpj=2393966)
CPU: After generic identify, caps: bfebfbff 28100000 00000000 00000000 0098e3fd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 28100000 00000000 00000000 0098e3fd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 28100000 00000000 00000940 0098e3fd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Xeon(R) CPU           X3430  @ 2.40GHz stepping 05
SMP alternatives: switching to SMP code
Booting processor 2/4 eip 3000
CPU 2 irqstacks, hard=c0754000 soft=c0734000
Initializing CPU#2
Calibrating delay using timer specific routine.. 4787.94 BogoMIPS (lpj=2393972)
CPU: After generic identify, caps: bfebfbff 28100000 00000000 00000000 0098e3fd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 28100000 00000000 00000000 0098e3fd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU: After all inits, caps: bfebfbff 28100000 00000000 00000940 0098e3fd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel(R) Xeon(R) CPU           X3430  @ 2.40GHz stepping 05
SMP alternatives: switching to SMP code
Booting processor 3/6 eip 3000
CPU 3 irqstacks, hard=c0755000 soft=c0735000
Initializing CPU#3
Calibrating delay using timer specific routine.. 4787.95 BogoMIPS (lpj=2393976)
CPU: After generic identify, caps: bfebfbff 28100000 00000000 00000000 0098e3fd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 28100000 00000000 00000000 0098e3fd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 256K
CPU: L3 cache: 8192K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU: After all inits, caps: bfebfbff 28100000 00000000 00000940 0098e3fd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel(R) Xeon(R) CPU           X3430  @ 2.40GHz stepping 05
Total of 4 processors activated (19154.80 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 4 CPUs: passed.
Brought up 4 CPUs
sizeof(vma)=88 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=136 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
migration_cost=60
checking if image is initramfs... it is
Freeing initrd memory: 3128k freed
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
Boot video device is 0000:1c:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 *7 10 11 14 15)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
PCI: Bridge: 0000:00:03.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
  IO window: disabled.
  MEM window: df000000-df8fffff
  PREFETCH window: de000000-deffffff
PCI: Bridge: 0000:00:1c.3
  IO window: disabled.
  MEM window: df900000-df9fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
  IO window: 2000-2fff
  MEM window: dfa00000-dfafffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.

jodgen

续。。。。。。


ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:03.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1c.3 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.4 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x38 set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
type=2000 audit(1368589132.988:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
alg: No test for crc32c (crc32c-generic)
ksign: Installing public key data
Loading keyring
- Added public key 31B497468CDD12CF
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie01]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI: Processor [CPU3] (supports 8 throttling states)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: No controller found.
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S4 S5)
Freeing unused kernel memory: 228k freed
Write protecting the kernel read-only data: 396k
Time: tsc clocksource has been installed.
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1a.0 to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
PCI: cache line size of 32 is not supported by device 0000:00:1a.0
ehci_hcd 0000:00:1a.0: irq 169, io mem 0xdfd01800
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.0 to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
PCI: cache line size of 32 is not supported by device 0000:00:1d.0
ehci_hcd 0000:00:1d.0: irq 66, io mem 0xdfd01c00
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.12
ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 18 (level, low) -> IRQ 185
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
usb 1-1: new high speed USB device using ehci_hcd and address 2
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x1830 ctl 0x1824 bmdma 0x1810 irq 185
ata2: SATA max UDMA/133 cmd 0x1828 ctl 0x1820 bmdma 0x1818 irq 185
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 6 ports detected
usb 2-1: new high speed USB device using ehci_hcd and address 2
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 6 ports detected
ata1.00: ATA-7: GB0500EAFJH, HPGB, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
usb 1-1.4: new high speed USB device using ehci_hcd and address 3
ata2: SATA link down (SStatus 0 SControl 300)
  Vendor: ATA       Model: GB0500EAFJH       Rev: HPGB
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write through
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write through
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 177
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
usb 1-1.4: configuration #1 chosen from 1 choice
input: Avocent Virtual Media KVM Module as /class/input/input0
input: USB HID v1.10 Keyboard [Avocent Virtual Media KVM Module] on usb-0000:00:1a.0-1.4
input: Avocent Virtual Media KVM Module as /class/input/input1
input: USB HID v1.10 Mouse [Avocent Virtual Media KVM Module] on usb-0000:00:1a.0-1.4
PCI: Setting latency timer of device 0000:00:1f.5 to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0x1888 ctl 0x183c bmdma 0x1870 irq 177
ata4: SATA max UDMA/133 cmd 0x1880 ctl 0x1838 bmdma 0x1878 irq 177
usb 2-1.1: new full speed USB device using ehci_hcd and address 3
usb 2-1.1: configuration #1 chosen from 1 choice
input: ServerEngines SE USB Device as /class/input/input2
input: USB HID v1.11 Keyboard [ServerEngines SE USB Device] on usb-0000:00:1d.0-1.1
input: ServerEngines SE USB Device as /class/input/input3
input: USB HID v1.11 Mouse [ServerEngines SE USB Device] on usb-0000:00:1d.0-1.1
usb 2-1.5: new low speed USB device using ehci_hcd and address 4
usb 2-1.5: configuration #1 chosen from 1 choice
input: Dell Dell USB Entry Keyboard as /class/input/input4
input: USB HID v1.10 Keyboard [Dell Dell USB Entry Keyboard] on usb-0000:00:1d.0-1.5
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: hp       DVDROM DH20N, EB00, max UDMA/100
ata3.00: configured for UDMA/100
usb 2-1.6: new low speed USB device using ehci_hcd and address 5
usb 2-1.6: configuration #1 chosen from 1 choice
input: Logitech USB Optical Mouse as /class/input/input5
input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.0-1.6
ata4: SATA link down (SStatus 0 SControl 300)
  Vendor: hp        Model: DVDROM DH20N      Rev: EB00
  Type:   CD-ROM                             ANSI SCSI revision: 05
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: dm-devel@redhat.com
device-mapper: dm-raid45: initialized v0.2429
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: dm-0: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 50954243
ext3_orphan_cleanup: deleting unreferenced inode 50954244
EXT3-fs: dm-0: 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux:  Disabled at runtime.
SELinux:  Unregistering netfilter hooks
type=1404 audit(1368589159.266:2): selinux=0 auid=4294967295 ses=4294967295
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k4
e1000e: Copyright (c) 1999-2008 Intel Corporation.
ACPI: PCI Interrupt 0000:20:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:20:00.0 to 64
Generic PHY: Registered new driver
input: PC Speaker as /class/input/input6
eth0: (PCI Express:2.5GB/s:Width x1) 00:22:64:89:91:4c
eth0: Intel(R) PRO/1000 Network Connection
eth0: MAC: 3, PHY: 8, PBA No: e56869-003
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
tg3.c:v3.93 (May 22, 200
ACPI: PCI Interrupt 0000:1e:00.0[A] -> GSI 19 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:1e:00.0 to 64
eth1: Tigon3 [partno(BCM95723) rev 5784100 PHY(5784)] (PCI Express) 10/100/1000Base-T Ethernet d8:d3:85:d7:ec:82
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[76180000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 185
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 2:0:0:0: Attached scsi generic sg1 type 5
sr0: scsi3-mmc drive: 12x/40x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
usb 2-1.6: USB disconnect, address 5
  Vendor: KVM       Model: vmDisk-CD         Rev: 0.01
  Type:   CD-ROM                             ANSI SCSI revision: 00
sr1: scsi3-mmc drive: 0x/0x caddy
sr 4:0:0:0: Attached scsi CD-ROM sr1
sr 4:0:0:0: Attached scsi generic sg2 type 5
usb-storage: device scan complete
floppy0: no floppy controllers found
lp: driver loaded but no devices found
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
usb 2-1.6: new low speed USB device using ehci_hcd and address 6
usb 2-1.6: configuration #1 chosen from 1 choice
input: Logitech USB Optical Mouse as /class/input/input7
input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.0-1.6
EXT3 FS on dm-0, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 5144568k swap on /dev/VolGroup00/LogVol01.  Priority:-1 extents:1 across:5144568k
IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com>
tg3: eth1: Link is up at 100 Mbps, full duplex.
tg3: eth1: Flow control is on for TX and on for RX.
eth0: Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
eth1: no IPv6 routers present

wenhq

tg3: eth1: Link is up at 100 Mbps, full duplex.
tg3: eth1: Flow control is on for TX and on for RX.
eth0: Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX


ethtool eth0

ethtool eth1

看一下。怎么网卡自协商的速率不一样是不是连到了不同的switch的不同port，或者说是switch做什么操作了？

jodgen

wenhq 发表于 2013-05-20 09:19
tg3: eth1: Link is up at 100 Mbps, full duplex.
tg3: eth1: Flow control is on for TX and on for RX ...

两个网卡连接的都是普通的傻瓜交换机，当然是不同的交换机，因为两块网卡处于不同的网段

[root@Webquery ~]# ethtool eth0
Settings for eth0:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbag
        Wake-on: d
        Current message level: 0x00000001 (1)
        Link detected: yes
[root@Webquery ~]# ethtool eth1
Settings for eth1:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: g
        Wake-on: g
        Current message level: 0x000000ff (255)
        Link detected: yes
[root@Webquery ~]#

wenhq

你切换等级后还再贴一下上面的结果.

jodgen

wenhq 发表于 2013-05-20 09:33
你切换等级后还再贴一下上面的结果.

是否需要重启，重启后网络是断的，然后ethtool，在转换运行等级后，网络通了，继续ethtool，您说的是这个意思吗？

wenhq

init 3和init 5 切换的话,网络不断.只是增加一个GUI的东西.不要重起,因为你的问题是init3 和init 5的区别.

jodgen

wenhq 发表于 2013-05-20 09:41
init 3和init 5 切换的话,网络不断.只是增加一个GUI的东西.不要重起,因为你的问题是init3 和init 5的区别.

[root@Webquery ~]# runlevel
3 5
[root@Webquery ~]# init 3
[root@Webquery ~]#
[root@Webquery ~]# runlevel
5 3
[root@Webquery ~]# ethtool eth0
Settings for eth0:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbag
        Wake-on: d
        Current message level: 0x00000001 (1)
        Link detected: yes
[root@Webquery ~]# ethtool eth1
Settings for eth1:
        Supported ports: [ TP ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: g
        Wake-on: g
        Current message level: 0x000000ff (255)
        Link detected: yes
[root@Webquery ~]#

wenhq

这2个IP能ping 通不?