NetBSD 6.0.1 DHCP 获取地址失败，静态配置 IP 成功

白云深

最近在本本上装了 NetBSD 6.0.1。奇怪的是，地址 dhcp 方式获取不了，静态配置可以。哪位达人指点一下，先行谢过。

在系统启动的时候有这样的打印:

route: writing to routing socket: network is unreachable

google 了一下，找到一个FreeBSD 上类似的问题，但看半天没看懂人家咋解决的：

http://forums.freebsd.org/showthread.php?p=183560


静态配置时的，rc.conf 相关内容：

1. 
   
2. rc_configured=YES
   
3. 
   
4. # Add local overrides below
   
5. #
   
6. hostname=NETBSD
   
7. # ifconfig_wm0=dhcp
   
8. ifconfig_wm0="inet 192.168.1.120 netmask 255.255.255.0"
   
9. sshd=YES
   
10. ntpd=NO
    
11. wscons=YES
    
12. defaultroute=192.168.1.1
    

复制代码

dhcp 方式时的 rc.conf:

1. 
   
2. rc_configured=YES
   
3. 
   
4. # Add local overrides below
   
5. #
   
6. hostname=NETBSD
   
7. ifconfig_wm0=dhcp
   
8. # ifconfig_wm0="inet 192.168.1.120 netmask 255.255.255.0"
   
9. sshd=YES
   
10. ntpd=NO
    
11. wscons=YES
    
12. # defaultroute=192.168.1.1
    

复制代码

执行

1. 
   
2. # /etc/rc.d/network restart
   

复制代码

后的输出：

1. 
   
2. Stopping network.
   
3. Deleting aliases.
   
4. Downing network interfaces: wm0.
   
5. Starting network.
   
6. Hostname: NETBSD
   
7. IPv6 mode: host
   
8. Configuring network interfaces: wm0.
   
9. Adding interface aliases:.
   

复制代码

ifconfig wm0 的输出：

1. 
   
2. wm0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
   
3.         capabilities=7ff80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx,TCP6CSUM_Rx,TCP6CSUM_Tx,UDP6CSUM_Rx,UDP6CSUM_Tx,TSO6>
   
4.         enabled=0
   
5.         address: 00:24:7e:68:40:40
   
6.         media: Ethernet autoselect (100baseTX full-duplex,flowcontrol,rxpause,txpause)
   
7.         status: active
   
8.         inet6 fe80::224:7eff:fe68:4040%wm0 prefixlen 64 scopeid 0x1
   

复制代码

以下是 dmesg:

1. 
   
2. Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
   
3.     2006, 2007, 2008, 2009, 2010, 2011, 2012
   
4.     The NetBSD Foundation, Inc.  All rights reserved.
   
5. Copyright (c) 1982, 1986, 1989, 1991, 1993
   
6.     The Regents of the University of California.  All rights reserved.
   
7. 
   
8. NetBSD 6.0.1 (GENERIC)
   
9. total memory = 3032 MB
   
10. avail memory = 2969 MB
    
11. timecounter: Timecounters tick every 10.000 msec
    
12. timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
    
13. LENOVO 6475DR2 (ThinkPad T400)
    
14. mainbus0 (root)
    
15. cpu0 at mainbus0 apid 0: Intel(R) Core(TM)2 Duo CPU     P8700  @ 2.53GHz, id 0x1067a
    
16. cpu1 at mainbus0 apid 1: Intel(R) Core(TM)2 Duo CPU     P8700  @ 2.53GHz, id 0x1067a
    
17. ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 20, 24 pins
    
18. acpi0 at mainbus0: Intel ACPICA 20110623
    
19. acpi0: X/RSDT: OemId <LENOVO,TP-7U   ,00002160>, AslId < LTP,00000000>
    
20. acpiecdt0 at acpi0: ACPI Embedded Controller via ECDT
    
21. acpi0: SCI interrupting at int 9
    
22. timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
    
23. hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
    
24. timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
    
25. acpiec0 at acpi0 (EC, PNP0C09-0): using acpiecdt0
    
26. MEM (PNP0C01) at acpi0 not configured
    
27. acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
    
28. acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
    
29. SIO (PNP0C02) at acpi0 not configured
    
30. attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43 irq 0
    
31. pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
    
32. midi0 at pcppi1: PC speaker
    
33. sysbeep0 at pcppi1
    
34. npx1 at acpi0 (FPU, PNP0C04): io 0xf0 irq 13
    
35. npx1: reported by CPUID; using exception 16
    
36. pckbc1 at acpi0 (KBD, PNP0303) (kbd port): io 0x60,0x64 irq 1
    
37. pckbc2 at acpi0 (MOU, IBM0057) (aux port): irq 12
    
38. TPM (INTC0102) at acpi0 not configured
    
39. acpibat0 at acpi0 (BAT0, PNP0C0A-0): ACPI Battery
    
40. acpibat0: LGC LION rechargeable battery
    
41. acpibat0: granularity: low->warn 0.001 Wh, warn->full 0.001 Wh
    
42. acpiacad0 at acpi0 (AC, ACPI0003-0): ACPI AC Adapter
    
43. thinkpad0 at acpi0 (HKEY, IBM0068)
    
44. acpivga0 at acpi0 (VID): ACPI Display Adapter
    
45. acpiout0 at acpivga0 (LCD0, 0x0400): ACPI Display Output Device
    
46. acpiout0: brightness levels: 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 100
    
47. acpiout1 at acpivga0 (CRT0, 0x0100): ACPI Display Output Device
    
48. acpiout2 at acpivga0 (DVI0, 0x0300): ACPI Display Output Device
    
49. acpiout3 at acpivga0 (DVI1, 0x0301): ACPI Display Output Device
    
50. acpiout4 at acpivga0 (DVI2, 0x0302): ACPI Display Output Device
    
51. acpivga0: unknown output device acpiout1
    
52. acpivga0: unknown output device acpiout2
    
53. acpivga0: unknown output device acpiout3
    
54. acpivga0: unknown output device acpiout4
    
55. acpivga0: connected output devices:
    
56. acpivga0:   0x0400 (acpiout0): Unknown Output Device, head 0
    
57. acpiwmi0 at acpi0 (WMI1, PNP0C14-1): ACPI WMI Interface
    
58. acpiwmibus at acpiwmi0 not configured
    
59. acpitz0 at acpi0 (THM0)
    
60. acpitz0: levels: critical 127.0 C, passive cooling
    
61. acpitz1 at acpi0 (THM1): cpu0 cpu1
    
62. acpitz1: levels: critical 100.0 C, passive 95.5 C, passive cooling
    
63. apm0 at acpi0: Power Management spec V1.2
    
64. attimer1: attached to pcppi1
    
65. pckbd0 at pckbc1 (kbd slot)
    
66. pckbc1: using irq 1 for kbd slot
    
67. wskbd0 at pckbd0: console keyboard
    
68. pms0 at pckbc1 (aux slot)
    
69. pms0: Synaptics touchpad version 7.0
    
70. pms0: Passthrough, Palm detect
    
71. pckbc1: using irq 12 for aux slot
    
72. wsmouse0 at pms0 mux 0
    
73. pci0 at mainbus0 bus 0: configuration mode 1
    
74. pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
    
75. pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x2a40 (rev. 0x07)
    
76. agp0 at pchb0: detected 32764k stolen memory
    
77. agp0: aperture at 0xd0000000, size 0x10000000
    
78. vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x2a42 (rev. 0x07)
    
79. vga1: WARNING: ignoring 64-bit BAR @ 0x10
    
80. vga1: WARNING: ignoring 64-bit BAR @ 0x18
    
81. wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
    
82. wsmux1: connecting to wsdisplay0
    
83. i915drm0 at vga1: Mobile IntelM-BM-. GM45 Express Chipset
    
84. i915drm0: AGP at 0xd0000000 256MB
    
85. i915drm0: Initialized i915 1.6.0 20080730
    
86. vendor 0x8086 product 0x2a43 (miscellaneous display, revision 0x07) at pci0 dev 2 function 1 not configured
    
87. vendor 0x8086 product 0x2a44 (miscellaneous communications, revision 0x07) at pci0 dev 3 function 0 not configured
    
88. pciide0 at pci0 dev 3 function 2: vendor 0x8086 product 0x2a46 (rev. 0x07)
    
89. pciide0: bus-master DMA support present, but unused (no driver support)
    
90. pciide0: primary channel wired to native-PCI mode
    
91. pciide0: using ioapic0 pin 18 for native-PCI interrupt
    
92. atabus0 at pciide0 channel 0
    
93. pciide0: secondary channel wired to native-PCI mode
    
94. atabus1 at pciide0 channel 1
    
95. vendor 0x8086 product 0x2a47 (serial communications, interface 0x02, revision 0x07) at pci0 dev 3 function 3 not configured
    
96. wm0 at pci0 dev 25 function 0: 82801I mobile (AMT) LAN Controller (rev. 0x03)
    
97. wm0: interrupting at ioapic0 pin 20
    
98. wm0: PCI-Express bus
    
99. wm0: FLASH
    
100. wm0: Ethernet address 00:24:7e:68:40:40
     
101. ukphy0 at wm0 phy 2: OUI 0x000ac2, model 0x000b, rev. 1
     
102. ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
     
103. uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x2937 (rev. 0x03)
     
104. uhci0: interrupting at ioapic0 pin 20
     
105. usb0 at uhci0: USB revision 1.0
     
106. uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x2938 (rev. 0x03)
     
107. uhci1: interrupting at ioapic0 pin 21
     
108. usb1 at uhci1: USB revision 1.0
     
109. uhci2 at pci0 dev 26 function 2: vendor 0x8086 product 0x2939 (rev. 0x03)
     
110. uhci2: interrupting at ioapic0 pin 22
     
111. usb2 at uhci2: USB revision 1.0
     
112. ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x293c (rev. 0x03)
     
113. ehci0: interrupting at ioapic0 pin 23
     
114. ehci0: EHCI version 1.0
     
115. ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
     
116. usb3 at ehci0: USB revision 2.0
     
117. hdaudio0 at pci0 dev 27 function 0: HD Audio Controller
     
118. hdaudio0: interrupting at ioapic0 pin 17
     
119. hdafg0 at hdaudio0: Conexant CX20561
     
120. hdafg0: DAC00 2ch: HP Out [Jack]
     
121. hdafg0: ADC01 2ch: Mic In [Jack]
     
122. hdafg0: DAC02 2ch: Speaker [Built-In]
     
123. hdafg0: ADC03 2ch: Mic In [Built-In]
     
124. hdafg0: 2ch/2ch 44100Hz 48000Hz 96000Hz PCM16 PCM20 PCM24 AC3
     
125. audio0 at hdafg0: full duplex, playback, capture, independent
     
126. hdvsmfg at hdaudio0 not configured
     
127. ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x2940 (rev. 0x03)
     
128. ppb0: PCI Express 1.0 <Root Port of PCI-E Root Complex>
     
129. pci1 at ppb0 bus 2
     
130. pci1: i/o space, memory space enabled, rd/line, wr/inv ok
     
131. ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x2942 (rev. 0x03)
     
132. ppb1: PCI Express 1.0 <Root Port of PCI-E Root Complex>
     
133. pci2 at ppb1 bus 3
     
134. pci2: i/o space, memory space enabled, rd/line, wr/inv ok
     
135. iwn0 at pci2 dev 0 function 0: vendor 0x8086 product 0x4237 (rev. 0x00)
     
136. iwn0: interrupting at ioapic0 pin 17
     
137. iwn0: MIMO 1T2R, MoW, address 00:22:fa:eb:2b:72
     
138. iwn0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
     
139. iwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
     
140. iwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
     
141. ppb2 at pci0 dev 28 function 2: vendor 0x8086 product 0x2944 (rev. 0x03)
     
142. ppb2: PCI Express 1.0 <Root Port of PCI-E Root Complex>
     
143. pci3 at ppb2 bus 4
     
144. pci3: i/o space, memory space enabled, rd/line, wr/inv ok
     
145. vendor 0x8086 product 0x444e (miscellaneous memory, revision 0x11) at pci3 dev 0 function 0 not configured
     
146. ppb3 at pci0 dev 28 function 3: vendor 0x8086 product 0x2946 (rev. 0x03)
     
147. ppb3: PCI Express 1.0 <Root Port of PCI-E Root Complex>
     
148. pci4 at ppb3 bus 5
     
149. pci4: i/o space, memory space enabled, rd/line, wr/inv ok
     
150. ppb4 at pci0 dev 28 function 4: vendor 0x8086 product 0x2948 (rev. 0x03)
     
151. ppb4: PCI Express 1.0 <Root Port of PCI-E Root Complex>
     
152. pci5 at ppb4 bus 13
     
153. pci5: i/o space, memory space enabled, rd/line, wr/inv ok
     
154. uhci3 at pci0 dev 29 function 0: vendor 0x8086 product 0x2934 (rev. 0x03)
     
155. uhci3: interrupting at ioapic0 pin 16
     
156. usb4 at uhci3: USB revision 1.0
     
157. uhci4 at pci0 dev 29 function 1: vendor 0x8086 product 0x2935 (rev. 0x03)
     
158. uhci4: interrupting at ioapic0 pin 17
     
159. usb5 at uhci4: USB revision 1.0
     
160. uhci5 at pci0 dev 29 function 2: vendor 0x8086 product 0x2936 (rev. 0x03)
     
161. uhci5: interrupting at ioapic0 pin 18
     
162. usb6 at uhci5: USB revision 1.0
     
163. ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x293a (rev. 0x03)
     
164. ehci1: interrupting at ioapic0 pin 19
     
165. ehci1: EHCI version 1.0
     
166. ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
     
167. usb7 at ehci1: USB revision 2.0
     
168. ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0x93)
     
169. pci6 at ppb5 bus 21
     
170. pci6: i/o space, memory space enabled
     
171. cbb0 at pci6 dev 0 function 0: vendor 0x1180 product 0x0476 (rev. 0xba)
     
172. fwohci0 at pci6 dev 0 function 1: vendor 0x1180 product 0x0832 (rev. 0x04)
     
173. fwohci0: interrupting at ioapic0 pin 17
     
174. fwohci0: OHCI version 1.10 (ROM=0)
     
175. fwohci0: No. of Isochronous channels is 4.
     
176. fwohci0: EUI64 00:06:1b:03:2a:3c:fe:95
     
177. fwohci0: Phy 1394a available S400, 1 ports.
     
178. fwohci0: Link S400, max_rec 2048 bytes.
     
179. ieee1394if0 at fwohci0: IEEE1394 bus
     
180. fwip0 at ieee1394if0: IP over IEEE1394
     
181. fwohci0: Initiate bus reset
     
182. cbb0: cacheline 0x10 lattimer 0x20
     
183. cbb0: bhlc 0x822010
     
184. cbb0: interrupting at ioapic0 pin 16
     
185. cardslot0 at cbb0
     
186. cardbus0 at cardslot0: bus 22
     
187. pcmcia0 at cardslot0
     
188. ichlpcib0 at pci0 dev 31 function 0: vendor 0x8086 product 0x2917 (rev. 0x03)
     
189. timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
     
190. ichlpcib0: 24-bit timer
     
191. ichlpcib0: TCO (watchdog) timer configured.
     
192. gpio0 at ichlpcib0: 64 pins
     
193. piixide0 at pci0 dev 31 function 2: Intel 82801I Mobile Serial ATA Controller (ICH9) (rev. 0x03)
     
194. piixide0: bus-master DMA support present
     
195. piixide0: primary channel configured to compatibility mode
     
196. piixide0: primary channel interrupting at ioapic0 pin 14
     
197. atabus2 at piixide0 channel 0
     
198. piixide0: secondary channel configured to compatibility mode
     
199. piixide0: secondary channel interrupting at ioapic0 pin 15
     
200. atabus3 at piixide0 channel 1
     
201. ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x2930 (rev. 0x03)
     
202. ichsmb0: interrupting at ioapic0 pin 23
     
203. iic0 at ichsmb0: I2C bus
     
204. isa0 at ichlpcib0
     
205. acpicpu0 at cpu0: ACPI CPU
     
206. acpicpu0: C1: FFH, lat   1 us, pow  1000 mW
     
207. acpicpu0: C2: FFH, lat   1 us, pow   500 mW
     
208. acpicpu0: C3: FFH, lat  57 us, pow   100 mW, bus master check
     
209. acpicpu0: P0: FFH, lat  10 us, pow 35000 mW, 2534 MHz, turbo boost
     
210. acpicpu0: P1: FFH, lat  10 us, pow 35000 mW, 2533 MHz
     
211. acpicpu0: P2: FFH, lat  10 us, pow 15000 mW, 1600 MHz
     
212. acpicpu0: P3: FFH, lat  10 us, pow 12000 mW,  800 MHz
     
213. acpicpu0: T0: FFH, lat   1 us, pow 12000 mW, 100 %
     
214. acpicpu0: T1: FFH, lat   1 us, pow 10500 mW,  88 %
     
215. acpicpu0: T2: FFH, lat   1 us, pow  9000 mW,  75 %
     
216. acpicpu0: T3: FFH, lat   1 us, pow  7500 mW,  63 %
     
217. acpicpu0: T4: FFH, lat   1 us, pow  6000 mW,  50 %
     
218. acpicpu0: T5: FFH, lat   1 us, pow  4500 mW,  38 %
     
219. acpicpu0: T6: FFH, lat   1 us, pow  3000 mW,  25 %
     
220. acpicpu0: T7: FFH, lat   1 us, pow  1500 mW,  13 %
     
221. coretemp0 at cpu0: thermal sensor, 1 C resolution
     
222. acpicpu1 at cpu1: ACPI CPU
     
223. coretemp1 at cpu1: thermal sensor, 1 C resolution
     
224. fwohci0: BUS reset
     
225. fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
     
226. ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
     
227. ieee1394if0: bus manager 0
     
228. timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
     
229. acpiacad0: AC adapter online.
     
230. uhub0 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
     
231. uhub0: 2 ports with 2 removable, self powered
     
232. uhub1 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
     
233. uhub1: 6 ports with 6 removable, self powered
     
234. uhub2 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
     
235. uhub2: 2 ports with 2 removable, self powered
     
236. uhub3 at usb7: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
     
237. uhub3: 6 ports with 6 removable, self powered
     
238. uhub4 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
     
239. uhub4: 2 ports with 2 removable, self powered
     
240. uhub5 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
     
241. uhub5: 2 ports with 2 removable, self powered
     
242. uhub6 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
     
243. uhub6: 2 ports with 2 removable, self powered
     
244. uhub7 at usb6: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
     
245. uhub7: 2 ports with 2 removable, self powered
     
246. wd0 at atabus2 drive 0
     
247. wd0: <HITACHI HTS723216L9SA60>
     
248. wd0: drive supports 16-sector PIO transfers, LBA48 addressing
     
249. wd0: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
     
250. ugen0 at uhub0 port 1
     
251. ugen0: vendor 0x08ff Fingerprint Sensor, rev 2.00/17.03, addr 2
     
252. wd0: 32-bit data port
     
253. wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
     
254. wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
     
255. uvideo0 at uhub1 port 6 configuration 1 interface 0: Chicony Electronics Co., Ltd. Integrated Camera, rev 2.00/3.20, addr 2
     
256. video0 at uvideo0: Chicony Electronics Co., Ltd. Integrated Camera, rev 2.00/3.20, addr 2
     
257. ubt0 at uhub0 port 2
     
258. ubt0: Lenovo Computer Corp ThinkPad Bluetooth with Enhanced Data Rate II, rev 2.00/3.99, addr 3
     
259. atapibus0 at atabus3: 2 targets
     
260. cd0 at atapibus0 drive 0: <Optiarc  DVD RW AD-7910S, 9H52Q14E21, 1.D1> cdrom removable
     
261. cd0: 32-bit data port
     
262. cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
     
263. cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
     
264. Kernelized RAIDframe activated
     
265. boot device: wd0
     
266. root on wd0a dumps on wd0b
     
267. root file system type: ffs
     
268. wsdisplay0: screen 1 added (80x25, vt100 emulation)
     
269. wsdisplay0: screen 2 added (80x25, vt100 emulation)
     
270. wsdisplay0: screen 3 added (80x25, vt100 emulation)
     
271. wsdisplay0: screen 4 added (80x25, vt100 emulation)
     

复制代码

rcorder /etc/rc.d/* 的输出：

1. 
   
2. /etc/rc.d/wdogctl
   
3. /etc/rc.d/fsck_root
   
4. /etc/rc.d/root
   
5. /etc/rc.d/ccd
   
6. /etc/rc.d/rndctl
   
7. /etc/rc.d/cgd
   
8. /etc/rc.d/lvm
   
9. /etc/rc.d/raidframe
   
10. /etc/rc.d/DISKS
    
11. /etc/rc.d/swap1
    
12. /etc/rc.d/fsck
    
13. /etc/rc.d/mountcritlocal
    
14. /etc/rc.d/ttys
    
15. /etc/rc.d/bootconf.sh
    
16. /etc/rc.d/pf_boot
    
17. /etc/rc.d/ipsec
    
18. /etc/rc.d/ipfilter
    
19. /etc/rc.d/sysctl
    
20. /etc/rc.d/network
    
21. /etc/rc.d/wpa_supplicant
    
22. /etc/rc.d/dhclient
    
23. /etc/rc.d/dhcpcd
    
24. /etc/rc.d/ldpd
    
25. /etc/rc.d/npf
    
26. /etc/rc.d/pf
    
27. /etc/rc.d/route6d
    
28. /etc/rc.d/routed
    
29. /etc/rc.d/rtsold
    
30. /etc/rc.d/staticroute
    
31. /etc/rc.d/NETWORKING
    
32. /etc/rc.d/mountcritremote
    
33. /etc/rc.d/sysdb
    
34. /etc/rc.d/newsyslog
    
35. /etc/rc.d/wscons
    
36. /etc/rc.d/syslogd
    
37. /etc/rc.d/ppp
    
38. /etc/rc.d/named
    
39. /etc/rc.d/rtclocaltime
    
40. /etc/rc.d/ntpdate
    
41. /etc/rc.d/rpcbind
    
42. /etc/rc.d/ypserv
    
43. /etc/rc.d/ypbind
    
44. /etc/rc.d/yppasswdd
    
45. /etc/rc.d/mountall
    
46. /etc/rc.d/accounting
    
47. /etc/rc.d/amd
    
48. /etc/rc.d/perusertmp
    
49. /etc/rc.d/cleartmp
    
50. /etc/rc.d/dmesg
    
51. /etc/rc.d/veriexec
    
52. /etc/rc.d/ldconfig
    
53. /etc/rc.d/quota
    
54. /etc/rc.d/mountd
    
55. /etc/rc.d/nfsd
    
56. /etc/rc.d/nfslocking
    
57. /etc/rc.d/pwcheck
    
58. /etc/rc.d/gpio
    
59. /etc/rc.d/random_seed
    
60. /etc/rc.d/ipnat
    
61. /etc/rc.d/securelevel
    
62. /etc/rc.d/swap2
    
63. /etc/rc.d/virecover
    
64. /etc/rc.d/altqd
    
65. /etc/rc.d/ifwatchd
    
66. /etc/rc.d/isdnd
    
67. /etc/rc.d/downinterfaces
    
68. /etc/rc.d/ipfs
    
69. /etc/rc.d/ipmon
    
70. /etc/rc.d/kdc
    
71. /etc/rc.d/pflogd
    
72. /etc/rc.d/racoon
    
73. /etc/rc.d/savecore
    
74. /etc/rc.d/SERVERS
    
75. /etc/rc.d/DAEMON
    
76. /etc/rc.d/apmd
    
77. /etc/rc.d/bluetooth
    
78. /etc/rc.d/bootparams
    
79. /etc/rc.d/devpubd
    
80. /etc/rc.d/dhcpd
    
81. /etc/rc.d/dhcrelay
    
82. /etc/rc.d/ftp_proxy
    
83. /etc/rc.d/irdaattach
    
84. /etc/rc.d/local
    
85. /etc/rc.d/lpd
    
86. /etc/rc.d/makemandb
    
87. /etc/rc.d/mopd
    
88. /etc/rc.d/motd
    
89. /etc/rc.d/mrouted
    
90. /etc/rc.d/ntpd
    
91. /etc/rc.d/powerd
    
92. /etc/rc.d/rarpd
    
93. /etc/rc.d/rbootd
    
94. /etc/rc.d/rtadvd
    
95. /etc/rc.d/rwho
    
96. /etc/rc.d/screenblank
    
97. /etc/rc.d/timed
    
98. /etc/rc.d/tpctl
    
99. /etc/rc.d/LOGIN
    
100. /etc/rc.d/wsmoused
     
101. /etc/rc.d/sshd
     
102. /etc/rc.d/raidframeparity
     
103. /etc/rc.d/postfix
     
104. /etc/rc.d/ndbootd
     
105. /etc/rc.d/moused
     
106. /etc/rc.d/mixerctl
     
107. /etc/rc.d/mdnsd
     
108. /etc/rc.d/isibootd
     
109. /etc/rc.d/iscsi_target
     
110. /etc/rc.d/inetd
     
111. /etc/rc.d/identd
     
112. /etc/rc.d/httpd
     
113. /etc/rc.d/hostapd
     
114. /etc/rc.d/ftpd
     
115. /etc/rc.d/envsys
     
116. /etc/rc.d/cron
     

复制代码

f5b

没有用过NetBSD，由于在Windows和OpenBSD下面也碰到类似问题，分享个人经验

先假设
1、你在NetBSD下面的dhcp配置是正确的
2、局域网的dhcp服务正常。


dhcp无法获取ip，静态配置可以，在有线网络和无线网络我都碰到过
可能原因

有线网络
1、网卡质量差
2、网线质量差
3、网线过长。

无线网络
1、网卡质量差
2、无线信号差，如AP和电脑距离过远。

白云深

回复 2# f5b


这个系统本身我就是利用 PXE，从网络安装的，安装的时候 dhcp 可以正常工作。所以可以排除是硬件问题。我个人认识应该是软件问题，可能和 ipv6 或者 route 有关系。

不管如何，还是谢谢您的回复

白云深

有个日本人碰到的问题和我的很像：

http://d.hatena.ne.jp/steleto/20101225/1293291400

白云深

刚才抓了个包看了一下，实际上接口已经收到 dhcp ack 了，但又重新做了三个周期后才停止

白云深

问题解决了，应该是配置有问题导致的，调整后的 rc.conf 如下：

1. 
   
2. rc_configured=YES
   
3. 
   
4. # Add local overrides below
   
5. #
   
6. hostname=NETBSD
   
7. dhclient=YES
   
8. # ifconfig_wm0=dhcp
   
9. wscons=YES
   
10. sshd=YES
    
11. ntpd=N
    

复制代码

和原先的相比，多了 dhclient=YES, 少了 ifconfig_wm0=dhcp (这句是系统装好后就有的)

另外，wifi 接口还没配，如果不给 dhclient 指定接口的话，好像会一直尝试配置 wifi 接口，如果配置不成功，终端一直会有错误信息打印，挺烦人的。所以最好/etc/dhclient.conf 里指定接口
这个文件，我的系统里也没有，新建了一个，内容如下：

1. 
   
2. interface "wm0" {
   
3.         send-dhcp-client-identifier "client-wm0";
   
4. }
   

复制代码

好像用dhcpcd 来配置也可以，尝试了一下，没有成功，懒得折腾了，还是老老实实用 dhclient 了。

白云深

记得在安装过程中，好像有提示是否要把 dhcp 配置的网络信息写入 /etc ，当时选了否。也许当时选了是，就没有问题了。哎，人生就是折腾啊