- 论坛徽章:
- 20
|
本帖最后由 znnnz 于 2014-09-03 19:00 编辑
- -> set /SP/network commitpending=true
- Set 'commitpending' to 'true'
- -> set /SP/network pendingipaddress=192.168.0.96
- Set 'pendingipaddress' to '192.168.0.96'
- -> set /SP/network pendingipdiscovery=static
- Set 'pendingipdiscovery' to 'static'
- -> set /SP/network pendingipnetmask=255.255.255.0
- Set 'pendingipnetmask' to '255.255.255.0'
- -> set /SP/network pendingipgateway=192.168.0.1
- Set 'pendingipgateway' to '192.168.0.1'
- -> set /SP/network state=enabled
- Set 'state' to 'enabled'
- -> show /HOST obp_version
- /HOST
- Properties:
- obp_version = OpenBoot 4.34.2.a 2012/11/02 08:26
- -> show /HOST sysfw_version
- /HOST
- Properties:
- sysfw_version = Sun System Firmware 8.2.2.c 2012/12/11 20:49
- -> load -source tftp://192.168.0.198/Sun_System_Firmware-8_5_1_b-SPARC_T4-2.pkg
- NOTE: An upgrade takes several minutes to complete. ILOM
- will enter a special mode to load new firmware. No
- other tasks can be performed in ILOM until the
- firmware upgrade is complete and ILOM is reset.
- Are you sure you want to load the specified file (y/n)? y
- Preserve existing configuration (y/n)? y
- ....................................................................................................................
- Firmware update is complete.
- ILOM will now be restarted with the new firmware.
- -> /sbin/reboot
- INSwitchinWatchdogd: Stopping patting ... Done
- Stopping portmap daemon: portmap.
- Stopping : consd Done
- Stopping CDServer: cdserver Done
- Stopping FDServer: fdserver Done
- Stopping HIDServer: hidserver start-stop-daemon: warning: failed to kill 1390: No such process
- Done
- Stopping Network Interface Plugging Daemon: eth0.
- Stopping Token Server: tokend Done
- Stopping Video Server: adviserd Done
- Stopping : webgo Done
- Stopping the Health Monitor Daemon...
- Stopping Serial Server: seriald Done
- Stopping : eventmgr Done
- Stopping IPMI Stack: Done
- Stopping OpenBSD Secure Shell server: sshd.
- Stopping bbrd...
- Stopping periodic command scheduler: cron.
- Stopping Host deamon: hostd Done
- Saving the System Clock time to the Hardware Clock...
- Hardware Clock updated to Wed Sep 3 09:59:49 GMT 2014.
- Stopping Platform Obfuscation Daemon: pod Done
- Stopping : vbsc Done
- Unmounting remote and non-toplevel virtual filesystems...done.
- Created dump file: /coredump/sp_trace/reboot/dump.gz
- Unmounting local filesystems...done.
- Stopping : dynafrud Done
- .
- Sending all processes the TERM signal...done.
- Sending all processes the KILL signal...done.
- Rebooting... Restarting system.
- Primary Bootstrap.
- U-Boot 1.1.4
- Custom AST2100 U-Boot 3.0 (Jul 11 2014 - 14:59:12) r90525
- VGA buffer reserved 0x800000 bytes at 0x7800000
- sptrace allocated 0x100000 bytes at 0x7700000
- DRAM: 119 MB
- Flash bank 0 at 10000000 has 32MB in 256 sectors (chipSize 1<<25, ratio 1, bufSz 64).
- Flash bank 1 at 12000000 has 32MB in 256 sectors (chipSize 1<<25, ratio 1, bufSz 64).
- Flash: 64 MB
- Protecting U-Boot flash sectors; monitor_base=11040000.
- H/W: AST2200 SP Service Processor; SOC: AST2200 Rev. 02 ('A0')
- ARM restart caused by: watch-dog ExtRst# pin
- Galactic1: 0x4002e9c0, Galactic2: 0x0
- The host is OFF(S5) (hostWantsPwr=0, powerGood=0,
- allowPwrOn=1|0, outOfReset=0, fatalError=0).
- Reset straps=0x08819180, def. H-PLL=264 MHz, CPU/AHB=2:1, boot CS0# normal speed
- PCI w/VGA noVBIOS; NOR 38ns/byte; DRAM clock is M-PLL: 264 MHz (DDR2-528)
- DRAM: 128MB data - 8MB VGA, 32-bit noECC, 2 BA 10 CA, CL=4 BL=4 ap=1, 61440 us refr, DQSipv=0x2020202
- FPGA Version : 4.4.4.6
- ### Warning: RTC oscillator has/was stopped
- Date: 2014-09-03 (Wednesday) Time: 10:00:05
- Net: faradaynic#0, faradaynic#1
- Enter Diagnostics Mode ['q'uick/'n'ormal(default)/e'x'tended(manufacturing mode)] ..... 0
- Diagnostics Mode - NORMAL
- <DIAGS> Memory Data Bus Test ... PASSED
- <DIAGS> Memory Address Bus Test ... PASSED
- I2C Probe Test - SP
- Bus Device Address Result
- === ============================ ======= ======
- 6 SP FRUID (U1101) 0xA0 PASSED
- 6 DS1338(RTC) (U1102) 0xD0 PASSED
- <DIAGS> PHY #0 R/W Test ... PASSED
- <DIAGS> PHY #0 Link Status ... PASSED
- <DIAGS> ETHERNET PHY #0, Internal Loopback Test ... PASSED
- checking for abnormal reboots: 0.
- Booting linux in 0 seconds...
- Un-Protect Flash Bank # 1
- Un-Protect Flash Bank # 2
- flctrl: Recovery U-Boot (r77667) at 0x10040000 is valid (min. r39727).
- Trying primary image...
- Trying to boot package at 110a0000
- Found kernel image at 110a2000
- Found root image at 111f5a6c
- copying 0x00054040 bytes from 0x111f5a6c to 0x00800000
- bootargs= root=/dev/ram ramdisk_size=336 console=ttyS0,9600 bigphysarea=6144 ractrends.mtdblocks=env,0x20000,0x20000,realroot,0x1340000,0xc40000,vbscdir,0x1fa0000,0x40000,params,0x2000000,0x400000,persist,0x2400000,0x1000000,coredump,0x3400000,0xc00000,
- ## Booting image at 110a2000 ...
- Image Name: Linux-2.6.27.43
- Created: 2014-07-11 21:53:00 UTC
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 1391148 Bytes = 1.3 MB
- Load Address: 00008000
- Entry Point: 00008000
- Verifying Checksum ... OK
- OK
- do_bootm_linux() armlinux.c:109
- bootm
- 0x110a2000
- 0x00800000
- theKernel=00008000
- do_bootm_linux() armlinux.c:126 - 9
- ## Loading Ramdisk Image at 00800000 ...
- do_bootm_linux() armlinux.c:160 - 10
- Image Name:
- Created: 2014-07-11 22:45:24 UTC
- Image Type: ARM Linux RAMDisk Image (uncompressed)
- Data Size: 344064 Bytes = 336 kB
- Load Address: 00000000
- Entry Point: 00000000
- Verifying Checksum ... OK
- do_bootm_linux() armlinux.c:187 - 11
- do_bootm_linux() armlinux.c:250 - 15
- arch_number = 0x00000386
- env_t = 0x01ED0008
- boot_params = 0x40000100
- DRAM bank = 0x00000000
- -> start = 0x00000000
- -> size = 0x07700000
- ethaddr = 00:10:E0:3A:58:F3
- eth1addr = 00:10:E0:3A:58:F2
- ip_addr = 0.0.0.0
- baudrate = 9600 bps
- Sun extensions:
- bi_UBootEnvAddr = 0x10020000
- bi_UBootEnvSize = 0x00020000
- bi_flashstart = 0x10000000
- bi_flashsize = 0x04000000
- bi_flashbanksize = 0x02000000
- bi_flashbanks = 0x02
- bi_flashbankwidth = 0x01
- bi_flashsectorsize = 0x00020000
- bi_flashsectorcount = 0x00000200
- bi_boottype = 0x02
- bi_primarytype = 0x02
- bi_secondarytype = 0x02
- bi_booted = 0x110a0000
- bi_primary = 0x11040000
- bi_secondary = 0x10040000
- bi_primaryhdr = 0x110a0000
- bi_secondaryhdr = 0x100a0000
- bi_imagearea0 = 0x10040000
- bi_imagearea1 = 0x11040000
- bi_maximagesize = 0x00fc0000
- bi_min_firmware_rev = 0
- bi_sptrace_base = 0x07700000
- bi_sptrace_len = 0x00100000
- bi_vga_driver_base = 0x00000000
- bi_vga_driver_len = 0x00000000
- bi_apbclockhz = 0x03ef1480
- H/W: AST2200 SP Service Processor; SOC: AST2200 Rev. 02 ('A0')
- The host is OFF(S5) (hostWantsPwr=0, powerGood=0,
- allowPwrOn=1|0, outOfReset=0, fatalError=0).
- ARM Control reg: RR=0 HV=0 IC=1 BPd=0 RomP=0 SysP=0 BE=0 WB=1 DC=0 AlinFlt=1 MMU=0
- Cache Type reg: CType=0xe WB, sep.; I: 16KB of 32B lines 4-way; D: 16KB of 32B lines 4-way
- IC locked ways(3:0): 0000b, DC locked ways: 0000b
- Reset straps=0x08819180, def. H-PLL=264 MHz, CPU/AHB=2:1, boot CS0# normal speed
- H-PLL (params=0x04291) 264.000 MHz, M-PLL params=0x04120-->264.000 MHz
- CPUCLK: H-PLL/1=264 MHz, AHB HCLK: CPUCLK/2=132 MHz, APB PCLK: H-PLL/4= 66 MHz
- PCI w/VGA noVBIOS; NOR 38ns/byte; DRAM clock is M-PLL: 264 MHz (DDR2-528)
- Bus-master-mode clocks: LPC LHCLK= 33 MHz
- Stopped clocks: vidCap-1, SP-Display, HACE
- DRAM: 128MB data - 8MB VGA, 32-bit noECC, 2 BA 10 CA, CL=4 BL=4 ap=1, 61440 us refr, DQSipv=0x2020202
- Reset controls: HACE, PwmFt, PECI, displays, MDMA
- Register protect: SCU UNprot, DMC prot, AHBC prot, VIC U-prot
- Ethernet MAC-PHY interface mode=6 (RMII + RMII), no MII2DC+DIO pins
- do_bootm_linux() armlinux.c:266
- do_bootm_linux() armlinux.c:269
- do_bootm_linux() armlinux.c:273
- do_bootm_linux() armlinux.c:277
- do_bootm_linux() armlinux.c:289
- do_bootm_linux() armlinux.c:293
- do_bootm_linux() armlinux.c:297
- do_bootm_linux() armlinux.c:305
- Galactic register 1: 400329c0
- Starting watchdog timer.
- ast_init_watchdog: SCU registers are already unlocked.
- Starting kernel at 0x00008000...
- do_bootm_linux() armlinux.c:330
- do_bootm_linux() armlinux.c:334 (0x00000386,0x40000100)
- Uncompressing Linux.......................................................................................... done, booting the kernel.
- Linux version 2.6.27.43 (ilom@oracle) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 Fri Jul 11 14:52:48 PDT 2014
- CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
- Machine: ASPEED-AST2100
- Memory policy: ECC disabled, Data cache writeback
- CPU0: D VIVT write-back cache
- CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
- CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 30226
- Kernel command line: root=/dev/ram ramdisk_size=336 console=ttyS0,9600 bigphysarea=6144 ractrends.mtdblocks=env,0x20000,0x20000,realroot,0x1340000,0xc40000,vbscdir,0x1fa0000,0x40000,params,0x2000000,0x400000,persist,0x2400000,0x1000000,coredump,0x3400000,0xc00000,
- PID hash table entries: 512 (order: 9, 2048 bytes)
- console [ttyS0] enabled
- mach/timer.c: Just lost 86 clock interrupts.
- Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- Memory: 119MB = 119MB total
- Memory: 92756KB available (2564K code, 232K data, 120K init)
- Calibrating delay loop... 131.48 BogoMIPS (lpj=657408)
- Mount-cache hash table entries: 512
- Initializing cgroup subsys ns
- Initializing cgroup subsys cpuacct
- CPU: Testing write buffer coherency: ok
- net_namespace: 804 bytes
- NET: Registered protocol family 16
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
- TCP: Hash tables configured (established 4096 bind 4096)
- TCP reno registered
- NET: Registered protocol family 1
- checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
- Freeing initrd memory: 336K
- NetWinder Floating Point Emulator V0.97 (double precision)
- bigphysarea: Allocated 6144 pages at 0xc0855000.
- squashfs: version 3.4 (2008/08/26) Phillip Lougher
- squashfs: LZMA suppport for slax.org by jro
- JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
- msgmni has been set to 182
- Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
- io scheduler noop registered (default)
- ttyS0 at MMIO 0x1e783000 (irq = 9) is a GUC-ASPEED UART
- ttyS1 at MMIO 0x1e784000 (irq = 10) is a GUC-ASPEED UART
- brd: module loaded
- loop: module loaded
- FTGMAC100: ASPEED FTGMAC Driver, (Linux Kernel 2.6.28.9) 09/18/2010 - by ASPEED (NAPIv1.1 delay-work, bgt-16,periodic-1,2,3,4,WqJed)
- FTGMAC100: eth0: at 0xfe660000 IRQ:2 noWait:0, MAC 00:10:e0:3a:58:f3
- FTGMAC100: eth0:ftgmac100_reset, phyAddr=0x0, miiPhyId=0x0040_61e4
- FTGMAC100: lp->rx_descs = ffc00000, lp->rx_rx_descs_dma = 7172000
- FTGMAC100: lp->rx_buf = 00000000, lp->rx_buf_dma = 0
- FTGMAC100: lp->tx_descs = ffc01000, lp->tx_rx_descs_dma = 7184000
- FTGMAC100: lp->tx_buf = 00000000, lp->tx_buf_dma = 0
- ftgmac100_init: dev->priv5 is c704d000
- FTGMAC100: eth1: at 0xfe680000 IRQ:3 noWait:0, MAC 00:10:e0:3a:58:f2
- FTGMAC100: eth1:ftgmac100_reset, phyAddr=0xff, miiPhyId=0x0000_0002
- FTGMAC100: lp->rx_descs = ffc02000, lp->rx_rx_descs_dma = 7189000
- FTGMAC100: lp->rx_buf = 00000000, lp->rx_buf_dma = 0
- FTGMAC100: lp->tx_descs = ffc03000, lp->tx_rx_descs_dma = 719c000
- FTGMAC100: lp->tx_buf = 00000000, lp->tx_buf_dma = 0
- ftgmac100_init: dev->priv5 is c7188800
- Ractrends Flash mapping: 0x2000000 at 0x10000000
- Bank #0: Found 1 x16 devices at 0x0 in 8-bit bank
- Amd/Fujitsu Extended Query Table at 0x0040
- Bank #0: CFI does not contain boot bank location. Assuming top.
- number of CFI chips: 1
- Ractrends Flash mapping: 0x2000000 at 0x12000000
- Bank #1: Found 1 x16 devices at 0x0 in 8-bit bank
- Amd/Fujitsu Extended Query Table at 0x0040
- Bank #1: CFI does not contain boot bank location. Assuming top.
- number of CFI chips: 1
- Number of banks found = 2
- Concatenating MTD devices:
- (0): "Bank #0"
- (1): "Bank #1"
- into device "Concatenated Flash Banks"
- GetMTDPartitions() says string is "env,0x20000,0x20000,realroot,0x1340000,0xc40000,vbscdir,0x1fa0000,0x40000,params,0x2000000,0x400000,persist,0x2400000,0x1000000,coredump,0x3400000,0xc00000,"
- MTD Partition 0 : fullpart @ 0x0 of Size 0x4000000
- MTD Partition 1 : env @ 0x20000 of Size 0x20000
- MTD Partition 2 : realroot @ 0x1340000 of Size 0xc40000
- MTD Partition 3 : vbscdir @ 0x1fa0000 of Size 0x40000
- MTD Partition 4 : params @ 0x2000000 of Size 0x400000
- MTD Partition 5 : persist @ 0x2400000 of Size 0x1000000
- MTD Partition 6 : coredump @ 0x3400000 of Size 0xc00000
- FlashSize=0x2000000, PartitionCount=7
- Creating 7 MTD partitions on "Concatenated Flash Banks":
- 0x00000000-0x04000000 : "fullpart"
- 0x00020000-0x00040000 : "env"
- 0x01340000-0x01f80000 : "realroot"
- 0x01fa0000-0x01fe0000 : "vbscdir"
- 0x02000000-0x02400000 : "params"
- 0x02400000-0x03400000 : "persist"
- 0x03400000-0x04000000 : "coredump"
- wdt: WDT is installed.
- wdt: WDT nowayout = 1, heartbeat = 30 secs
- wdt: WDT guardstartupshutdown = 1
- wdt: WDT startuptimeout = 600, shutdowntimeout = 60
- wdt: WDT was enabled at driver start, time remaining 53 secs.
- wdt: Guarding startup, setting watchdog for 600 seconds.
- nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
- CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
- nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
- sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
- ip_tables: (C) 2000-2006 Netfilter Core Team
- TCP cubic registered
- NET: Registered protocol family 10
- ip6_tables: (C) 2000-2006 Netfilter Core Team
- NET: Registered protocol family 17
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RAMDISK: squashfs filesystem found at block 0
- RAMDISK: Loading 333KiB [1 disk] into ram disk... done.
- VFS: Mounted root (squashfs filesystem) readonly.
- Freeing init memory: 120K
- INIT: version 2.88 booting
- Creating /var tmpfs
- Creating directories in /var...done.
- Creating /var/log tmpfs...done.
- Running ldconfig...done
- Starting early kernel log daemon: klogd.
- Cleaning up ifupdown....
- Calculating module dependencies... done.
- Loading kernel module flashinfo.
- Loading kernel module helper.
- Loading kernel module dbgpersist.
- Loading kernel module gpiomgr.
- Loading kernel module gpioint.
- Loading kernel module fpga.
- Loading kernel module fpgaflash.
- Loading kernel module i2c-core.
- Loading kernel module i2c-dev.
- Loading kernel module i2c-algo-as.
- Loading kernel module i2c-aspeed.
- Loading kernel module i2c-boardinfo.
- Loading kernel module videocap.
- Loading kernel module usb.
- Loading kernel module sptrace.
- Mounted vbsc
- 00:00:32 Checking device file systems
- 00:00:33 Checking persist...
- 00:00:41 Checking params...
- 00:00:45 Checking coredump...
- 00:00:50 Finished check of device file systems
- Checking configuration files state ...
- Image date: Fri Jul 11 15:44:26 PDT 2014 Image revision: 90525
- Conf date: Tue Dec 11 20:47:22 PST 2012 Conf revision: 77667
- upgrading configuration data
- Running: program to save /conf on upgrade: saveConfOnUpgrade.
- Copying new /conf files
- Configuration files state good after upgrade.
- Setting the system clock.
- System Clock set to: Wed Sep 3 10:01:20 UTC 2014.
- Initializing SP Trace Buffers
- Setting up networking....
- Will now mount local filesystems:.
- Will now activate swapfile swap:done.
- Cleaning up temporary files...Cleaning /var/run...done.
- Cleaning /var/lock...done.
- .
- Starting capidirect daemon: capidirectd . Done
- Starting Platform Initialization: platinit.
- Verifying platform...done.
- Setting hostname to 'ORACLESP-AK00131754'...Hostname: ORACLESP-AK00131754.
- done.
- Configuring IPv6...done
- Calling iptables-restore
- Calling ip6tables-restore
- Configuring network interfaces...SIOCSIFNETMASK: Cannot assign requested address
- SIOCSIFBRDADDR: Cannot assign requested address
- Failed to bring up eth1.
- done.
- Setting kernel variables ... /etc/sysctl.conf...net.ipv4.conf.default.rp_filter = 1
- net.ipv4.conf.all.rp_filter = 1
- kernel.core_pattern = |/usr/local/sbin/process_coredump /coredump/%h.%e.core.%p
- done.
- Initializing random number generator...done.
- Starting portmap daemon....
- Starting NFS common utilities:.
- Cleaning up temporary files....
- Mounted all disk partitions.
- Created links for vbsc
- Starting ILOM Watchdog daemon.
- Done
- populating memstore vars from disk
- Running plat...Preparsing sensor.xml... ( took 4 seconds ) done
- Probing frus ...done
- Done running plat
- Identifying Product Data...Done
- Setting poweron delay...
- Starting Dynamic FRUID Daemon early init: dynafrud_early_init Done (0)
- INIT: Entering runlevel: 3
- Preparsing sensor.xml... ( took 0 seconds ) done
- Starting Event Manager: eventmgr . Done
- Starting ipmi log manager daemon: logmgr . Done
- Starting portmap daemon...Already running..
- Starting NFS common utilities:.
- Starting Boot Timer.
- Network Interface Plugging Daemon...start eth0...done.
- Starting system log daemon....
- Starting user mgmt upgrade program: usrmgt_upgrade.
- Starting kernel log daemon....
- SSH2 RSA key file already exists; Skipping key creation ...
- SSH2 DSA key file already exists; Skipping key creation ...
- Starting OpenBSD Secure Shell server: sshd.
- Starting the Health Monitor Daemon...
- Starting Host Console Daemon: consd . Done
- Starting Error Telemetry Collection Daemon: etcd . Done
- Starting Fault Diagnosis Daemon: fdd . Done
- Starting IPMI Stack: . Done
- Starting BBR daemon...
- bbrd started after 1 seconds.
- Starting SP fishwrap cache daemon: fishwrapd . Done
- Starting Host daemon: hostd . Done
- Starting Network Controller Sideband Interface Daemon: ncsid . Done
- Starting Platform Obfuscation Daemon: pod . Done
- Starting vbsc daemon: vbsc . Done
- Starting lu main daemon: lumain . Done
- Starting Serial Server: seriald . Done
- Starting HT sign on daemon: htsignond . Done
- Starting webgo Web Server: webgo . Done
- Starting Detection/Diagnosis After System Boot: dasboot Done
- Starting Servicetags discoverer: stdiscoverer.
- Starting Servicetags listener: stlistener.
- Starting Dynamic FRUID Daemon: dynafrud Done
- waiting for GM ready ...GM is ready
- ORACLESP-AK00131754 login: root
- Password:
- Detecting screen size; please wait...done
- Oracle(R) Integrated Lights Out Manager
- Version 3.2.1.9.b r90525
- Copyright (c) 2014, Oracle and/or its affiliates. All rights reserved.
- Warning: password is set to factory default.
- Hostname: ORACLESP-AK00131754
- -> show /HOST sysfw_version
- /HOST
- Properties:
- sysfw_version = Sun System Firmware 8.5.1.b 2014/07/11 15:46
- -> show /HOST obp_version
- /HOST
- Properties:
- obp_version = OpenBoot 4.36.1 2014/06/26 12:18
- ->
|
|
免费注册
发表于 2014-09-03 18:58
