免费注册 查看新帖 |

ChinaUnix.net

  平台 论坛 博客 文库
最近访问板块 发新帖
查看: 5282 | 回复: 4

[存储网络] 跪求DS6800串口线(serial conversion cable)线序 [复制链接]

论坛徽章:
0
发表于 2017-12-04 17:18 |显示全部楼层
跪求DS6800串口线(serial conversion cable)线序

论坛徽章:
0
发表于 2017-12-06 11:21 |显示全部楼层
Setting the IP address
Complete this task to set the IP addresses and other network information for the processor cards.

You can create a direct connection from your computer to either of the processor cards on the DS6000™. You can use the direct connection to set IP addresses, network masks, gateway IP addresses, and other network settings for one or both of the processor cards.
To set the IP address, perform the following steps:

Use the serial conversion cable that was shipped with the enclosure to attach your computer to the serial port on the enclosure.
serial port
Use a terminal emulator, such as NetTerm or Windows® HyperTerminal to connect to the server enclosure through the serial port that is located on the processor card. If you are using Windows HyperTerminal, you might need to provide a connection name and icon before you can specify the connection settings.
Choose a communications port, such as COM1 or COM3, and connect to the processor card using the following settings:

Remote connection setting        Remote connection value
Bits per second        38400
Data bits        8
Parity        None
Stop bits        1
Flow control        Hardware
Use the default user ID guest and the default password guest to access the processor card. Press Enter to get the command prompt.
If this is your first time setting the IP address, change the default guest password to one that you select.
Select Change 'guest' password from the Main Menu options.
Enter the current password. This is guest if you are changing it for the first time.
Enter the new password that you have chosen. You will receive a message stating that the password has been changed successfully.
Passwords must meet the following criteria:
Be six to 16 characters long.
Must contain five or more letters, and it must begin and end with a letter.
Must contain one or more numbers.
Cannot contain the user's user ID.
Is case-sensitive.
Four unique new passwords must be issued before an old password can be reused.
Note: You must use the serial conversion cable to connect your computer to the second processor card to change the password on that processor card. You cannot change the password for the second processor card while you are still connected to the first processor card.
Select Configure network parameters from the Main Menu options.
Select Use static IP addresses from the Network configuration menu options. Set the IP addresses and network masks for both processor cards by performing the following steps:
Change the IP address for the processor card to which you are connected. Select IP address for this node from the Static IP addresses configuration menu options, enter the new IP address for the current processor card, and press Enter.
Change the IP address for the other processor card. Select IP address for other node from the Static IP addresses configuration menu options, enter the new IP address for the other processor card, and press Enter.
Change the network mask for the processor card to which you are connected. Choose Network mask for this node from the Static IP addresses configuration menu options, enter the new network mask for the current processor card, and press Enter.
Change the network mask for the other processor card. Choose Network mask for other node from the Static IP addresses configuration menu options, enter the new network mask for the other processor card, and press Enter.
Select Gateway for this node from the Static IP addresses configuration menu options, enter the new Gateway IP address for the current processor card, and press Enter.
Note: To assign a storage unit without a gateway, enter the address 0.0.0.0.
Select Gateway for other node from the Static IP addresses configuration menu options, enter the new Gateway IP address for the other processor card, and press Enter.
Note: To assign a storage unit without a gateway, enter the address 0.0.0.0.
Select Back to Network Configuration to return to the Network configuration menu.
Select Advanced Configuration Options to set the domain name server and the gateway settings.
Select First DNS server from the Advanced network configuration options, enter the new DNS server address for the current processor card, and press Enter.
Select Second DNS server from the Advanced network configuration options, enter the new DNS server address for the other processor card, and press Enter.
Select Back to Network Configuration.
Select Back to Main Menu to return to the Main Menu.
Select Apply changes and exit from the options in the main menu to save your changes and exit the application. You can then disconnect the serial conversion cable from your computer to the processor card.
Ensure that you set the IP address on the management console and that it is cabled to the same subnet as the DS6000. Change the default guest password for the second processor card. This processor card might appear to already be set, but you must still change the default guest password.

论坛徽章:
0
发表于 2017-12-06 11:21 |显示全部楼层
Setting the IP address
Complete this task to set the IP addresses and other network information for the processor cards.

You can create a direct connection from your computer to either of the processor cards on the DS6000™. You can use the direct connection to set IP addresses, network masks, gateway IP addresses, and other network settings for one or both of the processor cards.
To set the IP address, perform the following steps:

Use the serial conversion cable that was shipped with the enclosure to attach your computer to the serial port on the enclosure.
serial port
Use a terminal emulator, such as NetTerm or Windows® HyperTerminal to connect to the server enclosure through the serial port that is located on the processor card. If you are using Windows HyperTerminal, you might need to provide a connection name and icon before you can specify the connection settings.
Choose a communications port, such as COM1 or COM3, and connect to the processor card using the following settings:

Remote connection setting        Remote connection value
Bits per second        38400
Data bits        8
Parity        None
Stop bits        1
Flow control        Hardware
Use the default user ID guest and the default password guest to access the processor card. Press Enter to get the command prompt.
If this is your first time setting the IP address, change the default guest password to one that you select.
Select Change 'guest' password from the Main Menu options.
Enter the current password. This is guest if you are changing it for the first time.
Enter the new password that you have chosen. You will receive a message stating that the password has been changed successfully.
Passwords must meet the following criteria:
Be six to 16 characters long.
Must contain five or more letters, and it must begin and end with a letter.
Must contain one or more numbers.
Cannot contain the user's user ID.
Is case-sensitive.
Four unique new passwords must be issued before an old password can be reused.
Note: You must use the serial conversion cable to connect your computer to the second processor card to change the password on that processor card. You cannot change the password for the second processor card while you are still connected to the first processor card.
Select Configure network parameters from the Main Menu options.
Select Use static IP addresses from the Network configuration menu options. Set the IP addresses and network masks for both processor cards by performing the following steps:
Change the IP address for the processor card to which you are connected. Select IP address for this node from the Static IP addresses configuration menu options, enter the new IP address for the current processor card, and press Enter.
Change the IP address for the other processor card. Select IP address for other node from the Static IP addresses configuration menu options, enter the new IP address for the other processor card, and press Enter.
Change the network mask for the processor card to which you are connected. Choose Network mask for this node from the Static IP addresses configuration menu options, enter the new network mask for the current processor card, and press Enter.
Change the network mask for the other processor card. Choose Network mask for other node from the Static IP addresses configuration menu options, enter the new network mask for the other processor card, and press Enter.
Select Gateway for this node from the Static IP addresses configuration menu options, enter the new Gateway IP address for the current processor card, and press Enter.
Note: To assign a storage unit without a gateway, enter the address 0.0.0.0.
Select Gateway for other node from the Static IP addresses configuration menu options, enter the new Gateway IP address for the other processor card, and press Enter.
Note: To assign a storage unit without a gateway, enter the address 0.0.0.0.
Select Back to Network Configuration to return to the Network configuration menu.
Select Advanced Configuration Options to set the domain name server and the gateway settings.
Select First DNS server from the Advanced network configuration options, enter the new DNS server address for the current processor card, and press Enter.
Select Second DNS server from the Advanced network configuration options, enter the new DNS server address for the other processor card, and press Enter.
Select Back to Network Configuration.
Select Back to Main Menu to return to the Main Menu.
Select Apply changes and exit from the options in the main menu to save your changes and exit the application. You can then disconnect the serial conversion cable from your computer to the processor card.
Ensure that you set the IP address on the management console and that it is cabled to the same subnet as the DS6000. Change the default guest password for the second processor card. This processor card might appear to already be set, but you must still change the default guest password.

论坛徽章:
0
发表于 2017-12-06 11:23 |显示全部楼层
Use a terminal emulator, such as NetTerm or Windows® HyperTerminal to connect to the server enclosure through the serial port that is located on the processor card. If you are using Windows HyperTerminal, you might need to provide a connection name and icon before you can specify the connection settings.
Choose a communications port, such as COM1 or COM3, and connect to the processor card using the following settings:

Remote connection setting        Remote connection value
Bits per second        38400
Data bits        8
Parity        None
Stop bits        1
Flow control        Hardware

论坛徽章:
0
发表于 2017-12-06 11:33 |显示全部楼层
set the IP address, perform the following steps:

Use the serial conversion cable that was shipped with the enclosure to attach your computer to the serial port on the enclosure

这个serial conversion cable不知道什么什么线,控制器上的接口是RJ11,接PC端应该是RS232的DB9,我根据接口定义做了根线接上有信号,但是乱码,波特率和流控都反复改动试了还是不行,求大神指点
您需要登录后才可以回帖 登录 | 注册

本版积分规则 发表回复

基于案例的 SQL 优化实战训练营

讲师:中电福富特级专家梁敬彬,参与本次课程培训,你将收获:
1. 能编写出较为高效的 SQL;
2. 能解决70%以上的数据库常见优化问题;
3. 能得到老师提供的高效的相关工具和解决方案;
4. 能举一反三,收获不仅仅是 SQL 优化。
现在购票享受8.8折优惠!
----------------------------------------
优惠时间:2019年3月20日前

大会官网>>
  

北京盛拓优讯信息技术有限公司. 版权所有 16024965号-6 北京市公安局海淀分局网监中心备案编号:11010802020122
中国互联网协会会员  联系我们:huangweiwei@it168.com
感谢所有关心和支持过ChinaUnix的朋友们 转载本站内容请注明原作者名及出处

清除 Cookies - ChinaUnix - Archiver - WAP - TOP