哪位好心人能提供比较新的MP（GSP）的资料

Superdome GSP 命令

Single PD User - Commands unique to user Serv
BO - Boot Protection Domain
-This command ensures that all the cells assigned to the target partition have valid complex profiles andthen releases Boot-Is-Blocked (BIB).

CP - Cells Assigned by Partition
-The CP command will display atable of cells assigned to partitions and arranged by cabinets.

DE - Display Entity Status
- This command displays the specifiedentity’s

DF - Display FRUID
- Displays the FRUID data of the specified

DU - Display USB Topology

ER - Enable Remote Console Access
- Enable or Disable remotemodem port access. GSP - Secure led, MP - Remote led

HE - Display Available Commands
- Lists all commands available to the user level: Admin, Oper or Serv - if defined

ID - Change Stable Complex Profile
- Configures the complex profile information. A valid golden profile must exist first.

LS - Display LAN Status
- Displays connection status of the GSP Customer and Private lan or the MP’s customer
lan.

MA - Return to Main menu

PS - Power Status
- Displays hardware status: B-CABINET,C-CELL, G-GSP, I-CIO. 8400/7410: T-CABINET, S-SYSTEM BACKPLANE, G-MP/CIO, P-PCI DOMAIN, C-CELL (cabinet option shows
present, available, and power status of all entities)

RR - Reset a Partition for Reconfiguration
- Resets the specified partition but does not boot it. Sets BIB flag. See BO command.

RS - Reset a Partiton
- The utility system resets each cell that is amember of the specified partition. Once all cells have completed rendez-vous, the partition is booted.

TC - Sends a TOC Signal to a Partition
- Transfers the control(TOC) of the specified partition. The SINC on each cell in the specified
partition asserts the sys_init signal to Dillon.

FW - RP8400 Firmware Update
- Use MP>; he fw for details.

OSP - Online Scan Programming Utility

SYSREV - System Revisions
- Report revs of programmable devices and F/W.

PWRGRD - RP8400/7410 Pwr Grid
- 1 = Grid A, 2 = Grid B, 3 =Grids A+B (7410: 4=A0+B0, 5=A1+B1) Rear View: B1 A1 B0 A0
TE - Broadcast a Message to all Users at GSP(MP)
:CM>; Up to 80 characters can be typed in and the message is broadcast to the other users in the
command menu. Users in the main menu are not shown the message.

VM - Margin the Voltage in a Cabinet
- Adjusts the voltage of all marginable supplies within a range of +/- 5%. Not available on RP8400/7410.

WHO - Display GSP Connected Users
- Displays the login name of the connected console client user and the port on which they are connected. For LAN console clients the remote IP address is displayed.

MR - Modem Reset
- This command sends an ATZ to the system modem connected to the remote port. Any modem connections will be lost.

MS - Modem Status
- The MS command displays the state of the modemlines connected to the remote/modem serial port. Status signals DCD, CTS,DSR, RI and startup signals DTR, RTS are displayed

IO - IO Chassis/Cell Connectivity
- Displays connectivity between Cellsand I/O chassis’. Extremely useful on Superdome.

IF - Display Network Information
- This command displays information about the network interfaces on the GSP or customer interface on the 8400/7410 Sbc = priv lan = gsp1, SBCH = customer lan = gsp0
_____________________________________
oPER - Commands unique to Oper - includes Serv commands

CA - Configure Asynchronous & Modem Parameters
- The CA command allows the user to set the communications parameters of the local
and remote RS232 port.

CC - Complex Configuration
- Genesis profile will select the lowest cell # that is connected to a CIO, Cell must be at BIB. Last profile retrieves the lastprofile - could retrieve garbage though.

DI - Disconnect Remote or LAN Console
- This command disconnects the remote/modem or LAN users from the GSP(MP)

IT - Modify Command Inactivity Timeout
- This timeout prevents a user from inadvertently keeping the GSP or MP command menu locked in aGSP command. Default is 3 minutes, adjustable (3 - 1440)

PD - Partition Number Default for Login Session
- The PD commandsets the default partition number used by commands which require a partitionnumber (e.g. RS or CO).

PE - Power Entities On or Off
- Turns power on/off to the specified entity: B-CABINET, C-CELL, I-HIOB RP8400/7410: T-CABINET, C-CELL, P-PCI DOMAIN (0=Front Right, 1=Front Left)

RE - Reset Entity
- Resets the specified entity: C-CELL, I-HIOB, M-MAIN BACKPLANE. RP8400/7410: C-CELL, P-PCI DOMAIN, S-SYSTEM BACKPLANE. Not recommended - use RS

RL - Rekey Complex Profile Lock
- The RL command rekeys the
complex profile lock. This command should only be used to recover from an error where the holder of the lock terminates before releasingthe lock. Rarely used.

XD - GSP(MP) Diagnostics and Reset
- Diagnostics and/or Reset of GSP(MP). 1=Parameter Chksum, 2=Ping, R=Reset, RP8400/7410:1 and 2 same as Superdome, 3=Soft Reset Master MP, 4=Soft Reset Slave MP, 5=Hard Reset Slave MP
- Note: bottom button on MP is reset.Holding button longer than 5 sec resets LC and SO parameters.
ADMIN - Commands unique to Admin - includes Serv & Oper

AR - Enable/Disable Automatic Restart
- ASR is triggered by timeout of a watchdog timer and resets the partition . Set by Alert level 13. Disabled by default.

DATE - Sets Date and Time
- Changes the value of the RTC on theGSP(MP). This controls chassis log timestamps.

DC - Reset Parameters to Default Configuration
   -  The DCcommand can reset all or a subset of the following parameters: CA, EL, ER, IT,
      LC  and SO.

DL - Disable LAN Access
- The DL command disables telnet to GSP LANs or the MP LAN. Use ND to disable diag
access.

EL - Enable LAN Access
- Enables telnet access to both GSP LANs or to the MP LAN.

LC- Configure LAN Connections
- Modifies the LAN configuration for both GSP LAN ports or the MP LAN The user can  set the IP address, network name, subnet mask, and gateway.

ND - Enable/Disable Network Diagnostics
- Enable on Superdome to allow JUST and FWUU to operate. 8400/7410 - N/A

SO - Security Options and Access Control
- Modifies security options and access control to the GSP(MP): 1=GSP(MP) Wide Parameters 2=User Edit, Add or Delete Parameters

MFG - Enter Manufacturing Level Command Mode
- This command is reserved for HP manufacturing and is available for internal
use only.

Help Commands
GSP(MP)>; he NOTEs to view latest release notes online
GSP(MP)>; he OVerview to view GSP overview infomation
GSP(MP)>; he TOPics to view available GSP topics
GSP(MP)>; he LIst to view available GSP commands

MP命令

sysrev - Display Firmware Revisions
who - Display MP Lan Connections
date - Configure Date & Time for logging.
ca - Configure Modem Parameters
de - Display Entity Status

fw, osp - Update Firmware Revisions

Entities upgraded by using the FW Command
 MP: MP
 Cell Board: PDC
                     PDHC  (filename is - sinc###.bin)Entities upgraded by using the

OSP Command Backplane: OSP  (Onboard Scan Programmer)
                     FM and GPM
 MP: CIO
 PCIBP: PCIHS (hotswap), PCILPM
 Cell Board: Bob and Drain (FPGAs), LPM
*** The firmware loading process is identical between the two
   servers, rp8400 and rp7410!

lc, ls - Config & Display Lan Connections
MP:CM>; lc
This command modifies the LAN parameters.
Current configuration of MP LAN interface
  MAC address : 00:30:6e:05:09:b0
  IP address : 15.45.202.200 (0x0f2dcac

  Hostname    : rtckey1
  Subnet mask : 255.255.248.0 (0xfffff800)
  Gateway    : 15.45.202.200 (0x0f2dcac

  Status       : UP and RUNNING
  AutoNegotiate : Enabled
  Data Rate    : 10 Mb/s
  Duplex       : Half
  Error Count : 0
  Last Error : none
Do you want to modify the configuration for the customer
  LAN? (Y/[N]) y
Current IP Address  is: 15.45.202.200
Do you want to modify it? (Y/[N]) n
The “ls” (LAN Status) command has identical
output as the “lc” command. The only
difference is that there are no prompts to
modify the configuration data.

xd, ru - Reset MP
MP:CM>; xd
MP Diagnostics and Reboot menu
------------------------------
      1. Parameters checksum
      2. Ping
      3. Soft Reset the Master MP
      4. Soft Reset the Slave MP
      5. Hard Reset the Slave MP
Enter your choice: 2
Enter IP address: 15.41.32.1
Test result is: PASS
MP:CM>; ru
This command resets the selected MP bus device.
B - BPS  (Bulk Power Supply)
A - PACI (Partition Console Interface)
G - MP (Management Processor)
H - PDHC (Cell Board Controller)
      Select device: h
Enter cell number: 0
Do you want to reset the Cell PDH Controller Slot 0? (Y/[N])y
 This command is typically used after loading firmware in order to reset an
entity and start execution of the new code, as is the case with the PDCH code.
 Resetting PDCH will not reset the PDC on the cell board! Use the “rs”
commnad to reset PDC.
Caution: Always follow firmware install procedures and only
      execute a reset when directed to by the procedures!

tc - TOC a Single Partition

rs – reset partition
this is a normal reset that will return a partition to BCH .
rr” – reset partition for reconfiguration
this reset will do the same as the rs  command but will cause the partition to stop and hold at BIB. The “bo”  command will release the partition from BIB.
tc – TOC partition
causes HPMC information to be saved and executes a crash dump of main memory before resetting the partition.
re – reset entity
will reset a single cell board or the entire system by  selecting “backplane”, as seen below. If a cell board is not part of  a partition this command can be used to reset it.
bo - Boot a Partition to BCH
MP:CM>; bo
This command boots the selected partition.
  Part#  Name
  -----  ----
   0)  rtckey1a
   1)  rtckey1b
Select a partition number: 0
Do you want to boot partition number 0? (Y/[N]) y

cp - Display Cell Assignments
MP:CM>; cp
--------------
Cabinet | 0  |
--------+----+
Slot |0123|
--------+----+
Part  0 |*.*.|
Part  1 |.*..|
This command is used to “release” a partition form BIB. Immediately
after issuing this command, and if the selected partition is at BIB, it
will boot to BCH in a matter of seconds.
If the selected partition is not a t BIB, this command has no effect.

pe - Power Entities On or Off
MP:CM>; pe
This command controls power enable to a hardware device.
T - Cabinet
C - Cell
P - IO Chassis
      Select Device: t
The power state is ON for Cabinet 0.
In what state do you want the power? (ON/OFF) off

df - Display FRU Information for an Entity
This command displays the FRU ID information for the selected FRU.
Do you want a specific FRU or a dump? ([S]/D) s
S - System Backplane
G - Management Processor (Core I/O)
D - DIMM
P - PCI Backplane
M - Mass Storage Backplane
I - PCI Power Module
B - Bulk Power Supply
C - Cell Board
H - Cell Board Controller (PDHC)
U - CPU - CPU (located on Cell)
      Select FRU : g
Enter Core IO number: 0
Note:
Selecting “d” instead of “s”
will display a different set of FRUs.
(see text below, in student manual)

cc - genesis partition
MP:CM>; ccThis command allows you to change the complex profile.
WARNING: You must either shut down the OSs for reconfiguration or
      execute the RR (reset for reconfiguration) command for all
      partitions before executing this command.

G - Build Genesis complex profile
L - Restore Last complex profile
      Select profile to build or restore: g
Building a genesis complex profile will create a complex profile
consisting of one partition with a single cell.

Choose the cell to use.
Enter cell number: 0
Do you want to modify the complex profile? (Y/[N]) y
->; The complex profile will be modified.
Note:
All partitions must be at BIB or the following
error message will occur:
“Sorry, command failed: RtnCodeCellSlotNotBootBlocked”

ps - Display status of selected MP bus device
         The following MP bus devices were found:
MP:CM>; ps

+---+----+-----+-------+-------+-----------+
| | |    |    |    |          |
| | | Sys |    |  IO | Bulk Pwr  |
|Cab| MP |Bkpln| Cells |Chassis| Supplies  |
| # | |    |0 1 2 3| 0 1 |0 1 2 3 4 5|
+---+----+-----+-------+-------+-----------|
| 0 | *  |  *  |* * | * * |* * * *  |
+---+----+-----+-------+-------+-----------+
Only HKP Voltage is required for
device on the MP (I2C) bus to report in
here. Devices seen here are not
necessarily powered up or initialized!

You may display detailed power and hardware status for the following items:
T - Cabinet
S - System Backplane
G - MP (Core I/O)
P - IO Chassis
C - Cell
      Select Device: t
.
.
Power Status
---------------+-----+-------+-------+-----------+
            |    |    |    |          |
            | Sys |    |  IO | Bulk Pwr  |
            |Bkpln| Cells |Chassis| Supplies  |
            |    |0 1 2 3| 0 1 |0 1 2 3 4 5|
---------------+-----+-------+-------+-----------|
Populated    |  *  |* * | * * |* * * *  |
Enabled    |  *  |* * | * * |* * * *  |
Power OK    |  *  |* * | * * |* * * *  |
Warning/Fault |    |    |    |          |
Attention LED |    |    |    |          |

el -  Enable telnet access
MP:CM>; el
Enable telnet access? (Y/[N]) y
->; Telnet access enabled.
id –
This command allows you to change certain fields in the Stable complex configuration portion of the complex profile.
Retrieving the stable complex configuration portion of the complex profile.
MP modifiable stable complex configuration data fields.
Model String          : 9000/800/S16K-A
Complex System Name : RTC-KEYSTONE 1
Complex Serial Number  : USR002300D
Original Product Number: A6093A
Current Product Number : A6093A
Enterprise Id       :
Do you want to modify any of this information? (Y/[N]) y
Lockword is: y000053dc
Enter Password: abcd  Note:Use SSKEY to generate the passwd.
Sorry, authentication error!  You are unable to modify this data.

pwrgrd - Power Commands
MP:CM>; pwrgrd
The current power configuration is: Grid A only
Power grid configuration preference.
   1. Grid A only
   2. Grid B only
   3. Grids A & B
      Select Option:
Note:
This command tells the MP how many AC power cables
are connected. If it is not correct, the BPSs
will flash their amber lights!

so – config user
MP:CM>; so
1. MP wide parameters
2. User parameters
   Which do you wish to modify? ([1]/2) 2
Current users:
   LOGIN          USER NAME                ACCESS       PART.  STATUS
  1 Admin          Administrator          Admin
  2 Oper          Operator                Operator
1 to 2 to edit, A to add, D to delete, Q to quit :

安腾MP命令

(<Ctrl>; + <b>; to access)

状态命令

CL - Console history
CP* - Display partition cell assignments
DF - Display Field Replaceable Unit ID
IO* - Display IO chassis/cell connectivity
LS - LAN status
MS - Status of the modem
PS - Power management module status
SL - Status Logs
SR - Display all firmware revisions
SS - System’s processor status
SYSREV* - Display revisions of all firmware entities in the complex.
VFP - Virtual front panel display

服务和控制命令

BO* - Boot a partition
MFG* - Enter the manufacturing mode. Quit with qmm of with this command
MR - Modem reset
PC - Remote power control
PCIOLAD* -  Activate/Deactivate a PCI card.
PE* - Power entities on or off
RR* - Reset a partition for reconfiguration
RS - System reset from RST signal
TC - Transfer of control; system reset through
   INIT signal
VM* - Margin the voltage in a cabinet

端口配置命令

CA - Configure serial port parameters
DL* - Disable Lan console access
EL - Enable LAN access options: telnet and web permissions
ER - Enable remote; modem access configurations
LC - Configure the LAN
ND* - Enable/Disable Network Diagnostics
PG - Configure paging
CO - Return to the redirected console mode
CSP - Connect to another service processor
DI - Disconnect remote or LAN connection
SE - Activate a system session on locator remote port
TE - Send message to other user
WHO - Display a list of connected users

一般配置命令

AC - Alert display configuration
BP - Reset BMC password
CE - Log a chassis code in the MP chassis code history buffer
CG - Generate RSA key pair of Self Signed Certificate
CT - Configure tracing into MP firmware
DATE* - Set the time and date
DC - Default configuration
EX - Exit from the MP command mode
HE - Prints a Help menu
IT - Modify MP inactivity timeout
LOC - Locator LED
OT - Disable over temperature control
PR - Power Restore Policy Configuration
RB - BMC reset through Toggle GPIO pin
SDM - Set display mode (hex or text)
SO - Security options and access control
VT - View trace buffer
XD - MP diagnostics and reset
XU - Upgrade the MP firmware
ZCTGNAYOR - Clear GSP NVM at your own risk
ZDTPMT - Dump the GSP internal postmortem trace
MP Complex Profile Commands

AR* - Configure the Automatic System Restart
CC* - Initiate a Complex Configuration
CP* - Display partition cell assignments
ID* - Change certain stable complex configuration profile fields
IO* - Display IO chassis/cell connectivity
PARPERM* - Enable/Disable Partition Reconfiguration
PD* - Modify default Partition for this login session.
RL* - Rekey Complex Profile Lock

Manufacturing Mode Commands

CM* - Modify clock margin
GSPMFG - Enter the manufacturing mode
GSPQMM - Quit the manufacturing mode
MFG - Enter (Exit*) the manufacturing mode
QMM - Quit the manufacturing mode
RD* - Read utility processor memory
RU* - Reset MP bus device
WF* - Write FRU ID data of an entity
WR* - Write utility processor memory