论坛徽章:: 0

电梯直达

1楼 [收藏(0)] [报告]

发表于 2006-05-13 09:46 |只看该作者 |倒序浏览

Hardware Reset...

@(#) SYSTEM CONTROLLER(SC) POST 43 2005/02/22 15:29
PSR = 0x044010e5
PCR = 0x04004000

      Memory size = 32MB

      SelfTest running at DiagLevel:0x20

SC Boot PROM          Test
      BootPROM CheckSum             Test
IU       Test
      IU instruction set             Test
      Little endian access          Test
FPU    Test
      FPU instruction set          Test
SparcReferenceMMU    Test
      SRMMU TLB RAM                Test
      SRMMU TLB Read miss          Test
      SRMMU page probe          Test
      SRMMU segment probe          Test
      SRMMU region  probe          Test
      SRMMU context probe          Test
IIep Internal Cache    Test
      DCACHE RAM access             Test
      DCACHE TAG access             Test
      DCACHE Read miss             Test
      DCACHE Read hit                Test
      DCACHE Write miss             Test
      DCACHE Write hit             Test
      ICACHE RAM access             Test
      ICACHE TAG access             Test
      ICACHE miss                   Test
      ICACHE hit                   Test
      ICACHE TAG flush             Test
PCIC    Test
      PCIC Probe                   Test
      PCIC Config Register Access    Test
      PCI  Master Abort             Test
      PCIC Init                      Test
Memory Test
      Memory Address                Test
      MemBankAddrTest: start address = 0x00010000
RIO Ebus    Test
      Rio Ebus Probe                Test
RIO Ethernet  Test
      Rio Enet Probe                Test
      Rio Ethernet Int Loopbacks    Test
DUART(16552) InterSC    Test
      Loopback                      Test
      COM3 port
      COM4 port
      Interrupt                      Test
      COM3 port    Intr #2

      COM4 port    Intr #2

System Clock    Test
      System Clock verify          Test
      Board0 Clock is selected
      75MHZ Fixed Crystal is the selected Clock Source
      CLK(Self) :0x0000ffff CLK(Other) : 0x0000ffff
      REF    : 0x00002204
      CLOCK(SELF) FREQ : 75.0 MHZ
      CLOCK(OTHER)  FREQ : 75.25 MHZ
SBBC PCI Controller    Test
      SBBC PCI Config Space probe    Test
      SBBC Internal Reg Access       Test
      SBBC Interrupts                Test
      Port1 interrupt generation Tests  INTR #14

      Port0 interrupt generation Tests  INTR #14

SBBC Device0          Test
      PS Fail Reg(SBBC Dev0)       Test
SBBC Device1          Test
      SRAM (SBBC Dev1)             Test
      Memory Address Test (Non-destructive)
SBBC Device2          Test
      BId&MFG Reg (SBBC Dev2)       Test
SBBC Device3          Test
      FRU Prsnt Reg (SBBC Dev3)    Test
SBBC Device5          Test
      EPLD (SBBC Dev5)             Test
TOD(M48T59)             Test
      TOD Init                      Test
      TOD Functional                Test
      TOD NVRAM(Non-Destructive)    Test
      TOD Interrupts                Test
I2C Register Access    Test
      Enable Mux Register          Test
      Channel Mux  Register          Test
      Add Command  Register          Test
      Data       Register          Test
Local I2C AT24C64    Test
      EEPROM    Device          Test
      performing eeprom sequential read

Local I2C PCF8591    Test
      VOLT_AD    Device          Test
      channel[00000001] Voltage(0x00000099) :1.49
      channel[00000002] Voltage(0x0000009C) :3.35
      channel[00000003] Voltage(0x00000099) :4.98
      channel[00000004] Voltage(0x00000000) :0.0
Local I2C LM75       Test
      TEMP0(IIep)  Device          Test
      Temperature : 48.0 Degree(C)

Local I2C LM75       Test
      TEMP1(Rio) Device          Test
      Temperature : 42.0 Degree(C)

Local I2C LM75       Test
      TEMP2(CBH) Device          Test
      Temperature : 51.0 Degree(C)

Local I2C PCF8574    Test
      Sc CSR    Device          Test
Console Bus Hub       Test
      CBH Register Access          Test
POST Complete.
ERI Device Present
Getting MAC address for SSC0
busyWait() timeout waiting for RRDY, status=0x6027c008
busyWait() timeout waiting for RRDY, status=0x6027c008
busyWait() timeout waiting for RRDY, status=0x6027c008
busyWait() timeout waiting for WRDY, status=0x60278008
Cannot read ID board; using MAC address from TODNVRAM
MAC address is 0:3:ba:9:e0:36
Hostname: gb132
Address: 172.16.10.71
Netmask: 255.255.0.0
Attached TCP/IP interface to eri unit 0
Attaching interface lo0...done
Gateway: 172.16.10.254
Timeout waiting for network driver (flags=0x8062)

      Copyright 2005 Sun Microsystems, Inc.  All rights reserved.
      Use is subject to license terms.

Sun Fire System Firmware
RTOS version: 43
ScApp version: 5.19.0 Build_01.0
SC POST diag level: min
busyWait() timeout waiting for RRDY, status=0x6027c008
                                                   busyWait() timeout waiting for RRDY, status=0x6027c008
                                                                                                         busyWait() timeout waiting for RRDY, status=0x6027c008
                           busyWait() timeout waiting for WRDY, status=0x60278008

The date is Friday, May 12, 2006, 9:10:23 PM CST.

May 12 21:10:24 gb132 Platform.SC: Boot: ScApp 5.19.0, RTOS 43
May 12 21:10:27 gb132 Platform.SC: SBBC Reset Reason(s): Power On Reset , SC Reset Button
May 12 21:10:27 gb132 Platform.SC: Initializing the SC SRAM
May 12 21:10:30 gb132 Platform.SC: ERROR: Boot Failure, ID0 not installed
May 12 21:10:30 gb132 Platform.SC: ERROR: Boot Failure, ID0 not installed
ERROR: PSU type not recognized, use A166
May 12 21:10:31 gb132 Platform.SC: SCC is inaccessible - please insert valid SCC