ProLiant ML350 G3服务器安装UnixWare 7.1.1的正确方法

lsw

在ProLiant ML350 G3服务器上安装SCO UnixWare 7.1.1，会出现以下问题，导致安装程序不能进行：
- 如果用2张启动软盘启动服务器，在按照屏幕提示插入#2软盘后报错，安装程序不能读取软盘，无法继续
- 如果直接用UnixWare光盘启动服务器，在按照提示插入HBA软盘后，安装程序不能正确识别HBA软盘；用Ctrl+Alt+Esc切换到控制台（console）端，报错如下：
WARNING: FDC unexpected state

解决办法
使用SCO UnixWare的ptf7619d启动&补丁软盘组，下载网址：
    ftp://ftp.sco.com/pub/unixware7/ptf7619d

制作软盘命令
# dd if=ptf7619d.boot1.img of=/dev/rdsk/f03ht bs=32k <-- Boot disk 1
# dd if=ptf7619d.boot2.img of=/dev/rdsk/f03ht bs=32k <-- Boot disk 2
# dd if=ptf7619d.supp.image of=/dev/rdsk/f03ht bs=32k <-- Supplemental floppy
使用制作出的启动软盘启动机器并安装操作系统，在安装程序最后，会提示插入PTF软盘。此时插入制作出的第三张软盘，即补丁盘，然后选择“Install A PTF”

用这种方法安装可以解决很多机器上的问题

answer

现在相信我上回说的了吧。
ibm255,580 G2,570G2
都有同样的问题。

lsw

对。我才刚测试完呀：）

answer

帮你补充一下。
Dear Caldera Customer,

Support Level Supplement (SLS) ptf7619d, the UnixWare 7.1.1 psm_apic Driver
Supplement and NSC 7.1.1+IP dependent node install supplement, addresses the
following problems:

1. Installation of UnixWare 7.1.1 hangs on systems with a clock speed greater
   than or equal to 1Ghz.

2. Support for UnixWare Non-Stop Clusters dependent node installation using the
   new Intel PRO/1000 F and PRO/1000 T Server Adapters.

3. Support for network installation of Unixware 7.1.1 using PRO/1000 Adapters.


Contents
--------

   ptf7619d.boot1.img      boot floppy 1 image
   ptf7619d.boot2.img      boot floppy 2 image
   ptf7619d.netinst1.img   netinstall floppy 1 image
   ptf7619d.netinst2.img   netinstall floppy 2 image
   sumrs                   sum -r checksums
   ptf7619d.supp.image     Supplement floppy image


Installation Instructions
-------------------------

1. For supporting systems with 1GHz or greater clock speed, new boot floppies
   are provided.

   Cut the boot floppies and a Supplemental floppy:

      # dd if=ptf7619d.boot1.img of=/dev/rdsk/f03ht bs=32k
      # dd if=ptf7619d.boot2.img of=/dev/rdsk/f03ht bs=32k
      # dd if=ptf7619d.supp.image of=/dev/rdsk/f03ht bs=32k
        (This is the Supplemental floppy.)

   Use the boot floppies to install the system.  Near the end of the
   installation, you will be prompted for a PTF floppy.  At this point
   insert the Supplementary diskette in the floppy drive and choose
   "Install A PTF".

   Note that ptf7619d itself is not applicable and cannot be installed on
   NSC systems.  The 1Ghz support does not apply for NSC systems.

2. For support of UnixWare Non-Stop Clusters dependent node installation
   using the the new Intel PRO/1000 F and PRO/1000 T Server Adapters,
   new boot and netinstall images are provided.  Please see the file
   README.ptf7619d for details.

3. For updated support of network installation of Unixware 7.1.1 using
   PRO/1000 Adapters, new netinstall floppies are provided.  Please see
   the file README.ptf7619d for details.


If you have questions regarding this SLS, or the product on which it is
installed, please contact your software supplier.

aswellas

580G2我安装没出现这样的问题？
但ibm x360 8686安装怎么都抱 错
在make filesystems时，出现一个红屏
无法安装过去
只能重起！
？？？？？？

aswellas

在红屏上出现的宝错信息是：
fatal error： a failure occurred while trying to make filesystems on your disk
prossible reasons for failure are：
--  the hard disk or hard disk controller is damaged
-- the data cable between the disk and the controller is damage
-- the external bus （if any） is incorrectly terminated！

我的hba盘是在ibm网站下的raid的ips hba盘亚！也在安装过程加了
可是每次都到最后出现这个，没法继续！

？？？？
难道ibm x360安不上unixware 7。1。1

fanqian

换套光盘

answer

原帖由 "aswellas" 发表：
在红屏上出现的宝错信息是：
fatal error： a failure occurred while trying to make filesystems on your disk
prossible reasons for failure are：
--  the hard disk or hard disk controller is damaged
..........

没有问题，看一下下面的文章
Certified For   UnixWare 7.1.1



Back to Search Form Date Issued:  07-MAR-2003
Manufacturer:  IBM
Model Number:  xSeries 360 (8686-6RX)  
Category:  Computer Systems
Product Description: Ports  3 USB, Keyboard Mouse  Clock Speed  1.6GHz.  
CPU Manufacturer  Intel  Max # of CPUs  4  
CPU Type  Intel Xeon  Case Type  Server Rack Mount  
Installed Memory in System (MB)  1024  Memory Type  DDR  
BIOS Manufacturer  IBM Surepath  BIOS Revision  44A  
BIOS is  Flash  Card Slots on Motherboard  6 Hot Plug PCI-X  
L2 Cache (kbytes)  256  L3 Cache (kbytes)  1024  
Monitor Manufacturer  IBM  Monitor Model  P76  
Monitor Screen Size Actual  17  Bus Type  64 bit PCI, PCI-X  
Hard Drive Type and Size  As specified by IBM ServerProven.  Hard Drive Model  As specified by IBM ServerProven.  


Link to Hardware Vendor's Home Page

Notes on This Product
For UnixWare 7.1.1, the latest Maintenance Pack for
UW7.1.1 is required, as well as the latest Adaptec
Ultra160 HBA driver (adst70) and the latest version of
ptf7619. These may be found in (respectively):

ftp://ftp.caldera.com/pub/unixware7/uw711pk/
ftp://ftp.caldera.com/pub/unixware7/drivers/storage/
ftp://ftp.caldera.com/pub/unixware7/

For Open UNIX 8.0.0, the latest Maintenance Pack for
OU8.0.0 is required. This may be found in:

http://wdb1.caldera.com/clbk_web/owa/dwn_customer

For OpenServer 5.0.6, Release Supplement rs506a is required.
This may be found:

ftp://ftp.caldera.com/pub/openserver5/rs506a



Peripheral Information No Peripheral Information Available

Last Updated: 06-DEC-2002

aswellas

老大，你好不容易来了？
按你说的，
我需要做Ultra160 HBA driver (adst70）的驱动盘？
ptf7619下载了，怎么加进去？（系统还没安好亚）！

answer

找一台unix或是linux的机器。将你下载的文件用dd 的命令景象到软盘上。使用软盘来安装启动。
HBA也要新的，你的mail是什么我把这几个文件发给你。
# dd if=/home/ptf7619d.boot1.img of=/dev/rdsk/f03ht  
# dd if=/home/ptf7619d.boot2.img of=/dev/rdsk/f03ht  
# dd if=/home/ptf7619d.supp.img of=/dev/rdsk/f03ht  
# dd if=/home/hba_711a.image of=/dev/rdsk/f03ht
假设这些文件都在/home下。