[求助]SUN U5 270开机键盘灯闪了四次，STOP+A后显示器无输出

roman_pan

原帖由 yuanmufaye 于 2006-9-22 16:23 发表
呵呵
问题搞定没？

还没呢，忙了一天刚下班

jian-yuyu

显卡拔出，再重插！

jian-yuyu

显卡拔出，再重插！

roman_pan

原帖由 jian-yuyu 于 2006-9-22 22:02 发表
显卡拔出，再重插！

U5是集成显卡的

roman_pan

原帖由 Philmoon 于 2006-9-22 14:17 发表


stop+a的问题跟OBP版本没关系。这个显示是由于把启动设备指向了net（或者你的硬盘坏了，系统没找到启动盘），等待网上boot server回答。无人回答则无法继续启动。所以现在是需要设法到ok下修改这个boot devic ...

首先，我试了盲打的那种方法。不行
然后，我有一张S9安装光盘的第一张，也就是INSTALL那一张，串口输出：

Can't open input device.
Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 270MHz), No Keyboard
OpenBoot 3.11, 128 MB memory installed, Serial #9840094.
Ethernet address 8:0:20:96:25:de, Host ID: 809625de.



Bad magic number in disk label                                       
Can't open disk label package
Boot device: net  File and args:
Network Link Setup Failed.
Please Check Cable and Try Again.
Network Link Setup Failed.
Please Check Cable and Try Again.
Timeout waiting for ARP/RARP packet
Network Link Setup Failed.
Please Check Cable and Try Again.
Network Link Setup Failed.
Please Check Cable and Try Again.
Timeout waiting for ARP/RARP packet
Network Link Setup Failed.
Please Check Cable and Try Again.
Network Link Setup Failed.
Please Check Cable and Try Again.
Timeout waiting for ARP/RARP packet
Network Link Setup Failed.
Please Check Cable and Try Again.
Network Link Setup Failed.
Please Check Cable and Try Again.
Timeout waiting for ARP/RARP packet
Network Link Setup Failed.
Please Check Cable and Try Again.
Network Link Setup Failed.
Please Check Cable and Try Again.
Timeout waiting for ARP/RARP packet

roman_pan

红字标识的是以前我没发现的
但这张S9的光盘是可以用的！

roman_pan

还有另一个想法就是，U5能不能像PC一样使用某个跳线恢复EPROM的默认值的？

withee

首先，你用你的串口线连333的那台机器，然后Ctrl-Break看能不能进OK，如果不能，说明你的线orPC有问题，换线看看；如果能说明你这台机器还是有些问题的。你没法进OK，自然也不能用光盘起动机器，把333那个机器的硬盘装到这台机器上看能不能起动，如果能用eeprom命令改output-device参数试试。

roman_pan

原帖由 withee 于 2006-9-22 22:53 发表
首先，你用你的串口线连333的那台机器，然后Ctrl-Break看能不能进OK，如果不能，说明你的线orPC有问题，换线看看；如果能说明你这台机器还是有些问题的。你没法进OK，自然也不能用光盘起动机器，把333那个机器的硬 ...

现在我已经没有硬盘了。我连333那台机子也进不了OK，但333那台机子是显示正常的。串口线有问题就不确定了。

roman_pan

最新情况：
我开机按下了STOP+D，然后串口就输出以下：
Hardware Power ON

@(#) Sun Ultra 5/10 UPA/PCI  3.11 Version 9 created 1998/03/06 10:31
Probing keyboard Done
%o0 = 0000.0000.0000.4001

Executing Power On SelfTest

@(#) Sun Ultra 5/10 (Darwin) POST 2.2.9 (Build No. 502) 17:54 on 02/19/98

CPU: UltraSPARC-LC (MHz: 271 Ecache Size:  256KB)

Init POST BSS
        Init System BSS
NVRAM
        NVRAM Battery Detect Test
        NVRAM Scratch Addr Test
        NVRAM Scratch Data Test
DMMU TLB Tags
        DMMU TLB Tag Access Test
DMMU TLB RAM
        DMMU TLB RAM Access Test
Probe Ecache
        Probe Ecache
Ecache Tests
        Ecache RAM Addr Test
        Ecache Tag Addr Test
        Ecache RAM Test
        Ecache Tag Test
All CPU Basic Tests
        V9 Instruction Test
        CPU Tick and Tick Compare Reg Test
        CPU Soft Trap Test
        CPU Softint Reg and Int Test
All Basic MMU Tests
        DMMU Primary Context Reg Test
        DMMU Secondary Context Reg Test
        DMMU TSB Reg Test
        DMMU Tag Access Reg Test
        DMMU VA Watchpoint Reg Test
        DMMU PA Watchpoint Reg Test
        IMMU TSB Reg Test
        IMMU Tag Access Reg Test
All Basic Cache Tests
        Dcache RAM Test
        Dcache Tag Test
        Icache RAM Test
        Icache Tag Test
        Icache Next Test
        Icache Predecode Test
Sabre MCU Control & Status Regs Init and Tests
        Init Sabre MCU Control & Status Regs
                Initializing SC registers in SabreIO
Memory Probe and Init
        Probe Memory
                INFO:    128MB Bank 0
                bank 2:   0MB
INFO: MC0 = 0x00000000.80001184, MC1 = 0x00000000.06459acb
        Ecache Access Test
        Malloc Post Memory
        Memory Addr with Ecache
        Load Post In Memory
        Run POST from MEM
        .........
loaded POST in memory
        Map PROM/STACK/NVRAM in DMMU
        Update Master Stack/Frame Pointers
All FPU Basic Tests
        FPU Regs Test
        FPU Move Regs Test
        FPU State Reg Test
        FPU Functional Test
        FPU Trap Test
UPA Data Bus Line Test
Memory Tests
        Init Memory
                INFO:    128MB at bank 0 stack 0 (2 dimms per bank)
........................................................................................................................
                INFO:      0MB at bank 0 stack 1
                INFO:      0MB at bank 2 stack 0
                INFO:      0MB at bank 2 stack 1
        Memory Addr with Ecache Test
                INFO:    128MB at bank 0 stack 0 (2 dimms per bank)
                INFO:      0MB at bank 0 stack 1
                INFO:      0MB at bank 2 stack 0
                INFO:      0MB at bank 2 stack 1
        ECC Memory Addr Test
                INFO:    128MB at bank 0 stack 0 (2 dimms per bank)
                INFO:      0MB at bank 0 stack 1
                INFO:      0MB at bank 2 stack 0
                INFO:      0MB at bank 2 stack 1
        Block Memory Addr Test
                INFO:    128MB at bank 0 stack 0 (2 dimms per bank)
                INFO:      0MB at bank 0 stack 1
                INFO:      0MB at bank 2 stack 0
                INFO:      0MB at bank 2 stack 1
        Block Memory Test
                INFO:    128MB at bank 0 stack 0 (2 dimms per bank)
Write 0x33333333.33333333 ........................................................................................................................
Read ........................................................................................................................
Write 0x55555555.55555555 ........................................................................................................................
Read ........................................................................................................................
Write 0xcccccccc.cccccccc ........................................................................................................................
Read ........................................................................................................................
Write 0xaaaaaaaa.aaaaaaaa ........................................................................................................................
Read ........................................................................................................................


                INFO:      0MB at bank 0 stack 1
                INFO:      0MB at bank 2 stack 0
                INFO:      0MB at bank 2 stack 1
        ECC Blk Memory Test
                INFO:    128MB at bank 0 stack 0 (2 dimms per bank)
Write 0xa5a5a5a5.a5a5a5a5 ........................................................................................................................
Read ........................................................................................................................
Write 0x96969696.96969696 ........................................................................................................................
Read ........................................................................................................................
Write 0xbbbbbbbb.bbbbbbbb ........................................................................................................................
Read ........................................................................................................................
Write 0xdddddddd.dddddddd ........................................................................................................................
Read ........................................................................................................................


                INFO:      0MB at bank 0 stack 1
                INFO:      0MB at bank 2 stack 0
                INFO:      0MB at bank 2 stack 1
All Basic Sabre MMU Tests
        Init Sabre
        PIO Decoder and BCT Test
        PCI Byte Enable Test
        Interrupt Map (short) Reg Test
        Interrupt Set/Clr Reg Test
        Sabre IOMMU Regs Test
        Sabre IOMMU RAM Address Test
        Sabre IOMMU CAM Address Test
        IOMMU TLB Compare Test
        IOMMU TLB Flush Test
        PBMA PCI Config Space Regs Test
        PBMA Control/Status Reg Test
        PBMA Diag Reg Test
        Sabre IO Regs Test
All Advanced CPU Tests
        DMMU Hit/Miss Test
        IMMU Hit/Miss Test
        DMMU Little Endian Test
        IU ASI Access Test
        FPU ASI Access Test
        Ecache Thrash Test
All CPU Error Reporting Tests
        CPU Data Access Trap Test
        CPU Addr Align Trap Test
        DMMU Access Priv Page Test
        DMMU Write Protected Page Test
All Advanced Sabre IOMMU Tests
        Init Sabre
        Consist DMA Rd, IOMMU miss Ebus Test
        Consist DMA Rd, IOMMU hit Ebus Test
        Consist DMA Wr, IOMMU miss Ebus Test
        Consist DMA Wr, IOMMU hit Ebus Test
        Pass-Thru DMA Rd, Ebus device Test
        Pass-Thru DMA Wr, Ebus device Test
        Consist DMA Rd, IOMMU LRU Lock Ebus Test
        Consist DMA Wr, IOMMU LRU Locked Ebus Test
All Basic Cheerio Tests
        Cheerio Ebus PCI Config Space Test
        Cheerio Ethernet PCI Config Space Test
        Cheerio Init
All Sabre IOMMU Error Reporting Tests
        Init Sabre
        PIO Read, Master Abort Test
        PIO Read, Target Abort Test


Status of this POST run:        PASS
manfacturing mode=OFF
Time Stamp [hour:min:sec] 14:41:27  [month/date year] 09/22 2006

            


Power On Selftest Completed
Software Power ON0.0000.0000.0000 ffff.ffff.f00b.4448 0002.3333.0200.001b

@(#) Sun Ultra 5/10 UPA/PCI  3.11 Version 9 created 1998/03/06 10:31
Clearing E$ Tags  Done
Clearing I/D TLBs Done
Probing Memory Done
MEM BASE = 0000.0000.0000.0000
MEM SIZE = 0000.0000.0800.0000
11-Column Mode Enabled
MMUs ON
Copy Done
PC = 0000.01ff.f000.1ffc
PC = 0000.0000.0000.2040
Decompressing into Memory Done
Size = 0000.0000.0006.e160
ttya initialized
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
UltraSPARC-IIi 2-2-2 module
Probing Memory Bank #0  64 +  64 : 128 Megabytes
Probing Memory Bank #2   0 +   0 :   0 Megabytes
Probing UPA Slot at 1e,0 Nothing There
Probing /pci@1f,0/pci@1,1 at Device 1  pci108e,1000 network
Probing /pci@1f,0/pci@1,1 at Device 2  SUNW,m64B
Probing /pci@1f,0/pci@1,1 at Device 3  ide disk cdrom
Probing /pci@1f,0/pci@1 at Device 1  Nothing there
Probing /pci@1f,0/pci@1 at Device 2  Nothing there
Probing /pci@1f,0/pci@1 at Device 3  Nothing there
Probing /pci@1f,0/pci@1 at Device 4  Nothing there
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
UltraSPARC-IIi 2-2-2 module
Probing Memory Bank #0  64 +  64 : 128 Megabytes
Probing Memory Bank #2   0 +   0 :   0 Megabytes
Probing UPA Slot at 1e,0 Nothing There
Probing /pci@1f,0/pci@1,1 at Device 1  pci108e,1000 network
Probing /pci@1f,0/pci@1,1 at Device 2  SUNW,m64B
Probing /pci@1f,0/pci@1,1 at Device 3  ide disk cdrom
Probing /pci@1f,0/pci@1 at Device 1  Nothing there
Probing /pci@1f,0/pci@1 at Device 2  Nothing there
Probing /pci@1f,0/pci@1 at Device 3  Nothing there
Probing /pci@1f,0/pci@1 at Device 4  Nothing there

Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 270MHz), No Keyboard
OpenBoot 3.11, 128 MB memory installed, Serial #9840094.
Ethernet address 8:0:20:96:25:de, Host ID: 809625de.



Boot device: net  File and args:                                      
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Timeout waiting for ARP/RARP packet
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Timeout waiting for ARP/RARP packet
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Timeout waiting for ARP/RARP packet
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.