F4800最大自检过程中断开连接（已解决）

maike_xiao

在F4800最大自检过程中每隔十分钟就提示
Connection dropped due to idle timeout (10 minutes)
Connection closed.

然后就得回车再进入domain 才能继续看到最大自检信息，请问各位老大这个参数在哪里设置啊？

{/N0/SB0/P3}     test case pattern = ffffffff.fffffee3
{/N0/SB2/P0}     test case pattern = ffffffff.fffffee3
{/N0/SB2/P1}     test case pattern = ffffffff.fffffee3
Connection dropped due to idle timeout (10 minutes)
Connection closed


System Controller '××××××':

    Type  0  for Platform Shell

    Type  1  for domain A console
    Type  2  for domain B console
    Type  3  for domain C console
    Type  4  for domain D console

    Input: 0
Enter Password:
Platform Shell

bimsb-sc:SC> console -d a

Connected to Domain A
{/N0/SB2/P0}     test case Pattern = 00000000.00000000
{/N0/SB2/P1}     test case Pattern = 00000000.00000000
{/N0/SB2/P2}     test case Pattern = 00000000.0000011c
{/N0/SB2/P3}     test case Pattern = 00000000.0000011c
{/N0/SB0/P2}     test case Pattern = 55555555.55555555
{/N0/SB0/P3}     test case Pattern = 55555555.55555555
{/N0/SB2/P0}     test case Pattern = ffffffff.fffffee3已解决

[ 本帖最后由 maike_xiao 于 2006-11-1 11:17 编辑 ]

filtercai

命令好像是setupplatform吧，记不清了。里面可以设一个idle timeout的值，设成0就不会自动断开了。

要不你5分钟敲一次回车也不会出现这个情况，：）

临尘居士

没事去回车一下是个办法

maike_xiao

多谢各位，问题已经解决，以前就找过这个地方竟然没看见，多谢1楼提醒，鄙视自己一下！
另外Sun Fire™ 6800/4810/4800/3800
Systems Platform
Administration Manual 5.12.5这本书里介绍setupplatform那部分少了部分内容，比如idle time的设定，不知是不是这个参数是不是跟firmware的版本有关系 。

f4800:SC> setupplatform

Network Configuration
---------------------
Is the system controller on a network? [yes]:
Use DHCP or static network settings? [static]:
Hostname [f4800]:
IP Address [192.168.0.49]:
Netmask [255.255.255.0]:
Gateway [192.168.0.1]:
DNS Domain []:
Primary DNS Server []:
Secondary DNS Server []:

Loghosts
--------
Loghost []:
Log Facility [local0]:

SNTP
----
SNTP server []:

SNMP
----
Platform Description [my computer]:
Platform Contact [ ]:
Platform Location [ ]:
Enable SNMP Agent? [no]:

ACLs
----
ACL for domain A [ SB0 SB2 SB4 IB6 IB8 ]: Nov 01 09:57:29 f4800 Platform.SC: Frame Manager monitoring is disabled, connection is down

ACL for domain B [ SB0 SB2 SB4 IB6 IB8 ]:
ACL for domain C [ SB0 SB2 SB4 IB6 IB8 ]:
ACL for domain D [ SB0 SB2 SB4 IB6 IB8 ]:

COD
---
PROC RTUs installed: 0
PROC Headroom Quantity (0 to disable, 4 MAX) [0]:
PROC RTUs reserved for domain A (0 MAX) [0]:
PROC RTUs reserved for domain B (0 MAX) [0]:
PROC RTUs reserved for domain C (0 MAX) [0]:
PROC RTUs reserved for domain D (0 MAX) [0]:

SC
--
SC POST diag Level [min]:
Enable SC Failover? [no]:
Logical Hostname or IP Address [ ]:

Security Options
----------------
Enable telnet servers? [yes]:
Idle connection timeout (in minutes; 0 means no timeout) [0]:

Partition Mode
--------------
Configure chassis for single or dual partition mode? [single]

[ 本帖最后由 maike_xiao 于 2006-11-1 11:15 编辑 ]

Barrfee

汗～，我也没有注意。赫赫

ignu

有没有什么方法让4800开机不做最大自检？要花很长时间啊

饮鸩止渴

setenv diag-switch? false

maike_xiao

当然可以啊，下面那个是把最大自检改成默认的步骤（你当然也可以改成最小模式 init －－－Only system board initialization code is run. No testing is done. This is a very fast pass through POST. ）


bimsb-sc:A> setupdomain

Domain Boot Parameters
----------------------
diag-level [mem2]: default
verbosity-level [max]: min
error-level [max]:
interleave-scope [within-board]:
interleave-mode [optimal]:
reboot-on-error [true]:
hang-policy [reset]:
OBP.use-nvramrc? [true]:
OBP.auto-boot? [false]: true
OBP.error-reset-recovery [sync]:

Loghosts
--------
Loghost []:
Log Facility [local0]:

SNMP
----
Domain Description [ ]:
Domain Contact [ ]:
The SNMP agent is disabled.