dell2950可以装bsd嘛？

optac

如题，谢谢!

大大狗

原帖由 optac 于 2007-2-1 15:25 发表
如题，谢谢!

装6.2吧 应该可以

optac

谢谢啊！

HonestQiao

确实可以　了。

optac

请帮我看看，我在dell2950上成功安装了FB6.2的i386版本，有个问题，机器后面有两个网卡（网卡1和2分别应该对应的是bce0和bce1吧），我配了ip地址给bce0，将网线插在网卡1上不通，还插在网卡2上就通了，按这样的话网卡1对应的应该是bce1,网卡2对应的是bce0.可是我给bce1也配了一个IP并将一根网线插在网卡1上，咋么也不通。下面是我新装系统的dmesg信息，请帮我分析一下吧，谢谢了！

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE #0: Fri Jan 12 11:05:30 UTC 2007
root@dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU 5130 @ 2.00GHz (1995.01-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6
Features=0xbfebfbff<FPU>
Features2=0x4e33d<SSE3,RSVD2,MON,DS_CPL,VMX,TM2,<b9>,CX16,<b14>,<b15>,<b18>>
AMD Features=0x20100000<NX>
AMD Features2=0x1<LAHF>
Cores per package: 2
real memory = 3489300480 (3327 MB)
avail memory = 3414519808 (3256 MB)
ACPI APIC Table: <DELL>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 2
ioapic1: Changing APIC ID to 3
ioapic1: WARNING: intbase 64 != expected base 24
ioapic2: Changing APIC ID to 4
ioapic2: WARNING: intbase 160 != expected base 88
ioapic3: Changing APIC ID to 5
ioapic3: WARNING: intbase 224 != expected base 184
ioapic0 <Version> irqs 0-23 on motherboard
ioapic1 <Version> irqs 64-87 on motherboard
ioapic2 <Version> irqs 160-183 on motherboard
ioapic3 <Version> irqs 224-247 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <DELL> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24> port 0x808-0x80b on acpi0
cpu0: <ACPI> on acpi0
cpu1: <ACPI> on acpi0
pcib0: <ACPI> port 0xcf8-0xcff on acpi0
pci0: <ACPI> on pcib0
pcib1: <ACPI> at device 2.0 on pci0
pci6: <ACPI> on pcib1
pcib2: <ACPI> at device 0.0 on pci6
pci7: <ACPI> on pcib2
pcib3: <ACPI> at device 0.0 on pci7
pci8: <ACPI> on pcib3
pcib4: <CI> at device 0.0 on pci8
pci9: <CI> on pcib4
bce0: <Broadcom> mem 0xf4000000-0xf5ffffff irq 16 at device 0.0 on pci9
bce0: ASIC ID 0x57081010; Revision (B1); PCI-X 64-bit 133MHz
miibus0: <MII> on bce0
brgphy0: <BCM5708C> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bce0: Ethernet address: 00:18:8b:46:36:6c
pcib5: <ACPI> at device 1.0 on pci7
pci10: <ACPI> on pcib5
pcib6: <CI> at device 0.3 on pci6
pci11: <CI> on pcib6
pcib7: <ACPI> at device 3.0 on pci0
pci1: <ACPI> on pcib7
pcib8: <ACPI> at device 0.0 on pci1
pci2: <ACPI> on pcib8
mfi0: <Dell> mem 0xd80f0000-0xd80fffff,0xfc5e0000-0xfc5fffff irq 78 at device 14.0 on pci2
mfi0: 1637 (223755200s/0x0020/0) - Shutdown command received from host
mfi0: 1638 (4278190080s/0x0020/0) - PCI 0x041028 0x0415 0x041028 0x041f03: Firmware initialization started (PCI ID 0015/1028/1f03/102
mfi0: 1639 (4278190080s/0x0020/0) - Type 18: Firmware version 1.00.02-0157
mfi0: 1640 (4278190093s/0x0008/0) - Battery Present
mfi0: 1641 (4278190121s/0x0004/0) - PD 08(e1/s255) event: Enclosure (SES) discovered on PD 08(e1/s255)
mfi0: 1642 (4278190121s/0x0002/0) - PD 08(e1/s255) event: Inserted: PD 08(e1/s255)
mfi0: 1643 (4278190121s/0x0002/0) - Type 29: Inserted: PD 08(e1/s255) Info: enclPd=08, scsiType=d, portMap=00, sasAddr=500180b043c76900,0000000000000000
mfi0: 1644 (4278190121s/0x0002/0) - PD 00(e1/s0) event: Inserted: PD 00(e1/s0)
mfi0: 1645 (4278190121s/0x0002/0) - Type 29: Inserted: PD 00(e1/s0) Info: enclPd=08, scsiType=0, portMap=01, sasAddr=50010b900037bd32,0000000000000000
mfi0: 1646 (4278190121s/0x0002/0) - PD 01(e1/s1) event: Inserted: PD 01(e1/s1)
mfi0: 1647 (4278190121s/0x0002/0) - Type 29: Inserted: PD 01(e1/s1) Info: enclPd=08, scsiType=0, portMap=02, sasAddr=50010b9000397c86,0000000000000000
mfi0: 1648 (4278190121s/0x0002/0) - PD 02(e1/s2) event: Inserted: PD 02(e1/s2)
mfi0: 1649 (4278190121s/0x0002/0) - Type 29: Inserted: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=50010b9000397c36,0000000000000000
mfi0: 1650 (4278190121s/0x0002/0) - PD 03(e1/s3) event: Inserted: PD 03(e1/s3)
mfi0: 1651 (4278190121s/0x0002/0) - Type 29: Inserted: PD 03(e1/s3) Info: enclPd=08, scsiType=0, portMap=08, sasAddr=50010b9000397cfe,0000000000000000
mfi0: 1652 (4278190121s/0x0002/0) - PD 04(e1/s4) event: Inserted: PD 04(e1/s4)
mfi0: 1653 (4278190121s/0x0002/0) - Type 29: Inserted: PD 04(e1/s4) Info: enclPd=08, scsiType=0, portMap=10, sasAddr=50010b9000397d9a,0000000000000000
mfi0: 1654 (4278190121s/0x0002/0) - PD 05(e1/s5) event: Inserted: PD 05(e1/s5)
mfi0: 1655 (4278190121s/0x0002/0) - Type 29: Inserted: PD 05(e1/s5) Info: enclPd=08, scsiType=0, portMap=20, sasAddr=50010b9000397dc6,0000000000000000
mfi0: 1656 (223755253s/0x0020/0) - Adapter ticks 223755253 elapsed 42s: Time established as 02/02/07 18:14:13; (42 seconds since power on)
mfi0: 1657 (223755309s/0x0008/0) - Battery temperature is normal
mfi0: 1658 (223755309s/0x0008/0) - Current capacity of the battery is above threshold
pcib9: <CI> at device 0.2 on pci1
pci3: <CI> on pcib9
pcib10: <ACPI> at device 4.0 on pci0
pci12: <ACPI> on pcib10
pcib11: <CI> at device 5.0 on pci0
pci13: <CI> on pcib11
pcib12: <ACPI> at device 6.0 on pci0
pci14: <ACPI> on pcib12
pcib13: <ACPI> at device 0.0 on pci14
pci15: <ACPI> on pcib13
pcib14: <ACPI> at device 0.2 on pci14
pci16: <ACPI> on pcib14
pcib15: <CI> at device 7.0 on pci0
pci17: <CI> on pcib15
pcib16: <ACPI> at device 28.0 on pci0
pci4: <ACPI> on pcib16
pcib17: <PCI> at device 0.0 on pci4
pci5: <PCI> on pcib17
bce1: <Broadcom> mem 0xf8000000-0xf9ffffff irq 16 at device 0.0 on pci5
bce1: ASIC ID 0x57081010; Revision (B1); PCI-X 64-bit 133MHz
miibus1: <MII> on bce1
brgphy1: <BCM5708C> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bce1: Ethernet address: 00:18:8b:46:36:6a
uhci0: <UHCI> port 0xdce0-0xdcff irq 21 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <UHCI> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI> port 0xdcc0-0xdcdf irq 20 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI> port 0xdca0-0xdcbf irq 21 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <UHCI> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <EHCI> mem 0xfc700400-0xfc7007ff irq 21 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI> on ehci0
usb3: USB revision 2.0
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
uhub4: vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.0b, addr 2
uhub4: multiple transaction translators
uhub4: 4 ports with 4 removable, self powered
pcib18: <ACPI> at device 30.0 on pci0
pci18: <ACPI> on pcib18
pci18: <display> at device 13.0 (no driver attached)
isab0: <PCI> at device 31.0 on pci0
isa0: <ISA> on isab0
atapci0: <Intel> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on pci0
ata0: <ATA> on atapci0
ata1: <ATA> on atapci0
fdc0: <floppy> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: does not respond
device_attach: fdc0 attach returned 6
sio0: <16550A> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
fdc0: <floppy> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: does not respond
device_attach: fdc0 attach returned 6
pmtimer0 on isa0
orm0: <ISA> at iomem 0xc0000-0xc8fff,0xc9000-0xc9fff,0xca000-0xcb7ff,0xec000-0xeffff on isa0
atkbdc0: <Keyboard> at port 0x60,0x64 on isa0
atkbd0: <AT> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: parallel port not found.
sc0: <System> at flags 0x100 on isa0
sc0: VGA <16>
vga0: <Generic> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
acd0: CDROM <HL> at ata0-master UDMA33
mfid0: <MFI> on mfi0
mfid0: 69376MB (142082048 sectors) RAID volume '' is optimal
mfid1: <MFI> on mfi0
mfid1: 1142272MB (2339373056 sectors) RAID volume '' is optimal
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/mfid0s1a
ukbd0: Dell Dell USB Keyboard, rev 1.10/3.01, addr 2, iclass 3/1
kbd2 at ukbd0
bce0: link state changed to UP

大大狗

ifconfig 看一下

optac

test# ifconfig
bce0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        options=3b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU>
        inet 192.168.1.200 netmask 0xffffff00 broadcast 192.168.1.255
        ether 00:18:8b:46:36:6c
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
bce1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        options=3b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU>
        ether 00:18:8b:46:36:6a
        media: Ethernet autoselect (none)
        status: no carrier
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
        inet6 ::1 prefixlen 128
        inet 127.0.0.1 netmask 0xff000000

LnBSD

2950的网卡就是反着的

菲平

wk...能装了啊...6.2 ?

不过,还是更心仪ibm的服务器了^_^

zhengwei_zw

1950一一样哈。不错！跑起来飞快