在线等：用串口装HP UNIX报错

inms2005

装一台老的L1000，通过串口，前面都一直OK，但到下面的部分时候就出错，然后就重启：
To discontinue search, press any key (termination may not be immediate).


   Path#  Device Path (dec)  Device Path (mnem)  Device Type
   -----  -----------------  ------------------  -----------
   P0     0/0/0/0            lan.192.168.10.254 LAN Module
   P1     0/0/1/1.2          intscsib.2          Random access media      
   P2     0/0/2/1.2                              Random access media      


Main Menu: Enter command or menu > bo p2
Interact with IPL (Y, N, or Cancel)?> n

Booting...
Boot IO Dependent Code (IODC) revision 1


HARD Booted.

ISL Revision A.00.43  Apr 12, 2000

ISL booting  hpux (;0):INSTALL

Boot
: disk(0/0/2/1.2.0.0.0.0.0;0):WINSTALL
11763712 + 1970264 + 2628048 start 0x200ae8




alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x7fa00000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 4.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.

    System Console is on the Built-In Serial Interface
    Swap device table:  (start & size given in 512-byte blocks)
        entry 0 - auto-configured on root device; ignored - no room
WARNING: np cannot be defaulted to primary swap.
WARNING: No dump devices are configured.  Dump is disabled.
Starting the STREAMS daemons-phase 1
Create STCP device files
          $Revision: vmunix:    vw: -proj    selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108'  Wed Nov  8 19:24:56 PST 2000 $
Memory Information:
    physical page size = 4096 bytes, logical page size = 4096 bytes
    Physical: 2097152 Kbytes, lockable: 1555712 Kbytes, available: 1801888 Kbytes

=======  05/17/07 00:54:11 EDT  HP-UX Installation Initialization. (Thu May 17
         00:54:11 EDT 2007)
         @(#) Ignit @(#) install/init (opt) $Revision: 10.285 $
       * Scanning system for IO devices...
       * Querying disk device: 0/0/1/1.2.0 ...
       * Setting keyboard language.
NOTE:   
         The console firmware terminal type is currently set to "hp". If you
         are using any other type of terminal you will see "garbage" on the
         screen following this message.
         If this is the case, you will need to either change the terminal type
         set in the firmware via GSP (if your GSP firmware version supports
         this feature), or change your terminal emulation to match the
         firmware. In either case you will need to restart if your terminal and
         the firmware terminal type do not match.
         Press the 'b' key if you want to reboot now.
        

正常情况应该是选键盘，选26，然后往下，但出现这个NOTE后就停在那里，敲回车要么重启，要么出现：

you specify an incorrect display.
itool: Awin-E-ScreenSize: asking for screen size failed
The user interface failed, would you like to restart it? ([y]/n): y
you specify an incorrect display.
itool: Awin-E-ScreenSize: asking for screen size failed
The user interface failed, would you like to restart it? ([y]/n):
you specify an incorrect display.
itool: Awin-E-ScreenSize: asking for screen size failed
The user interface failed, would you like to restart it? ([y]/n): y
选N的话就重启了。

lt_8816

是你的GSP 里的设置问题，要在GSP里将终端类型改为hp。具体怎么该，你看一下GSP里的帮助。

czyf2001

F8 ?

inms2005

原帖由 lt_8816 于 2007-5-17 16:28 发表
是你的GSP 里的设置问题，要在GSP里将终端类型改为hp。具体怎么该，你看一下GSP里的帮助。

谢谢，机器里原来类型是HPterm，我把他改成VT100就OK了。