如何在HPUX下安装两种驱动不同的磁带机?

init_0

请教各位大侠一个问题

现在有一台RX4640的HP小型机,OS的版本是11.23

这台小型机一边通过光纤交换机连接着i500磁带库,driver是ibm的,驱动是atdd

另外同时连接着HP的5300磁带机阵列,里面放着DAT72磁带机.

现在ioscan后,DAT72磁带机的驱动也成了atdd了(原来没有atdd的话,应该是hp自己的stape)

如何让DAT72磁带机的驱动变成STAPE呢？

[ 本帖最后由 init_0 于 2007-8-19 19:44 编辑 ]

tangye

8008107000

五“宅”一生

楼上方法最直接。呵呵！

wazhl

想听听 800 是怎么回复的?

init_0

800也没有办法

呵呵

另外，atdd是可以驱动两种磁带机的

五“宅”一生

楼主如何解决的？

kq01

1.先用ioscan 得到两个磁带不同的HW PATH
2.用insf 建立设备
3.如果不能建立，看看手册上面，需要到什么地方下载driver
如果还不行,800-810-7000找后线工程师

sun_up

Find your answer In the section of "Installation and Configuration" in Chapter 4 of "IBM tape device drivers  Installation and User's Guide"
ftp://ftp.software.ibm.com/storage/devdrvr/Doc

Configure Selected IBM Tape Devices with ATDD/ACDD:

-- Attaching Selected IBM Tape Devices to ATDD/ACDD During Auto Booting:

To claim a specific tape device with atdd/acdd during reboot, edit the ″Claiming Device″ section in the file of /sbin/init.d/atdd.
For example, to attach IBM 3590E11 medium changer with acdd driver:
1. To determine the HW path:
# ioscan -fnk|grep IBM autoch 0 0/3/0/0.5.1 schgr CLAIMED DEVICE IBM 03590E11

2. Comment out the command line(s) in the init script of /sbin/init.d/atdd:
- For tape drives:
   /opt/atdd/bin/atdd_claim -t
- For medium changers:
   /opt/atdd/bin/atdd_claim -c

3. Add a command line in the ″Configuring Device″ section in /sbin/init.d/atdd:
  /opt/atdd/bin/atdd_claim -H 0/3/0/0.5.1


-- Attaching Selected IBM Tape Devices to ATDD/ACDD Dynamically:
To dynamically attach selected IBM tape device after the ATDD installation, run the following commands.
1. To determine the HW path of the device:
# ioscan -fnk|grep IBM autoch 0 0/3/0/0.5.1 schgr CLAIMED DEVICE IBM 03590E11

2. To claim the device with ATDD/ACDD:
  # /opt/atdd/bin/atdd_claim -H 0/3/0/0.5.1

Note:

The dynamic attachment may be lost after the system reboots.

-- Attaching Selected IBM Tape Device with a Particular Driver:
Use the system ioscan and rmsf commands to force a non-atdd/acdd driver to bind an IBM tape device.
For example, force bind the IBM 3590E media changer with the HP native changer driver schgr with these steps:
1. Determine the HW path of the device:
# ioscan -fnk |grep IBM
tape 0 0/3/0/0.5.0 atdd CLAIMED DEVICE IBM 03590E11
autoch 0 0/3/0/0.5.1 acdd CLAIMED DEVICE IBM 03590E11

2. Remove the I/O configuration from the system:
# rmsf -H 0/3/0/0.5.1

3. Force binding:
# ioscan -M schgr -H 0/3/0/0.5.1

4. Create the device special files:
# insf -H 0/3/0/0.5.1

5. Verify the force binding:
# ioscan -fnk |grep IBM
tape 0 0/3/0/0.5.0 atdd CLAIMED DEVICE IBM 03590E11
autoch 0 0/3/0/0.5.1 schgr CLAIMED DEVICE IBM 03590E11

Note:
The force binding will be lost after the system reboots. To keep the binding to a selected device with a particular driver after a reboot,
add these command-lines in steps 2–4 in ″Claiming Device″ section in /sbin/init.d/atdd file.
For example,
# Configuring Device Section:
# add specific device claim here, for example
# /opt/atdd/bin/atdd_claim -H 0/3/0/0.5.1
# /opt/atdd/bin/atdd_claim -H 0/6/0/0.1.30.255.0.0.1
rmsf -H 0/3/0/0.5.1
ioscan -M schgr -H 0/3/0/0.5.1
insf -H 0/3/0/0.5.1