请问如何在sco openserver5.0.7上安装HP DAT24磁带机.急!

fclib

机器配置如下:
服务器:HP ML370G3
操作系统:sco openserver5.0.7
磁带机:HP DAT24e
____________________________________
在下面情况下不知输入什么东西,试过几个都不行.
Enter the prefix of the SCSI host adapter that supports this device
or press <Return>; for the default: 'ad160'
Enter h for a list of host adapters or enter q to quit:
_____________________________________
最后结果:
# tar c8v /u/aaa
tar:cannot open /dev/rct0
都不知哪里配置不行?

hao4488

1. 设置ＨＰ磁带机的ＩＤ号．
２用mkdev tape命令

hao4488

1. 设置ＨＰ磁带机的ＩＤ号．
２用mkdev tape命令

sdccf

回答的太简单了。

giggle5

关键是scsi卡的驱动.你的是不是adaptec 39160.如过是在Enter the prefix of the SCSI host adapter that supports this device
or press <Return>; for the default: 'ad160'
Enter h for a list of host adapters or enter q to quit:
这里直接回车就可以.
tar c8v /u/aaa
tar:cannot open /dev/rct0
这里是磁带机还没有配好.关键是id号和scsi通道.

ludde

# mkdev tape
                 * Config the Tape Device
Tape Drive Configuration Program

        1. Configure a SCSI or Enhanced IDE tape drive
        2. Configure a different type of tape drive

        Select an option or enter q to quit: 1



SCSI or Enhanced IDE Tape Drive Configuration Program

        1. Install a SCSI Tape Drive
        2. Install an Enhanced IDE Tape Drive
        3. Remove a SCSI Tape Drive
        4. Remove an Enhanced IDE Tape Drive
        5. Change default Tape Drive
        6. View Current SCSI and Enhanced IDE Tape Drive configuration

        Select an option or enter q to return to main menu: 6

Error: There are no SCSI or Enhanced IDE tapes currently configured.



SCSI or Enhanced IDE Tape Drive Configuration Program

        1. Install a SCSI Tape Drive
        2. Install an Enhanced IDE Tape Drive
        3. Remove a SCSI Tape Drive
        4. Remove an Enhanced IDE Tape Drive
        5. Change default Tape Drive
        6. View Current SCSI and Enhanced IDE Tape Drive configuration

        Select an option or enter q to return to main menu: 1

Enter the prefix of the SCSI host adapter that supports this device
or press <Return>; for the default: 'ad160'
Enter h for a list of host adapters or enter q to quit: ad160
                          * Onboard SCSI host adapter is ‘ad160’
Which 'ad160' SCSI host adapter supports this device?
Select 0-1, or enter q to quit: 1
                                  *   ‘1’---interface on the back ; ‘0’---default connect with HDD
'ad160' SCSI host adapter 1 is not configured.
Would you like to update the link-kit? (y/n) y

What SCSI Bus is this device attached to?
Press <Return>; to use the default:0
Select 0-n, or h for help, or q to quit: 0

What is the Target ID for this device?
Select 0-15, or h for help, or q to quit: 6
                                           *   ‘6’ is the dial number at the Tape
What is the LUN of this device?
Press <Return>; to use the default: 0
Select 0-7, or h for help, or q to quit: 0

You are about to add the following SCSI device:

Host
Adapter         Adapter
Type   Device   Number  ID      LUN     BUS
----------------------------------------------
ad160    Stp     1       6       0       0

Update SCSI configuration? (y/n) y

The SCSI configuration file has been updated.

Adding device to system configuration files ...

System files have been successfully updated.

Configuring Tape Driver ...( Stp )


Enter Vendor Identification string or
press <Return>; to use default
or enter q to return to main menu:


Enter SCSI version that device is conformant to or
press <Return>; to use default
or enter q to return to main menu:


Enter Response Data Format that device uses or
press <Return>; to use default
or enter q to return to main menu:

The following tape drive types are supported:

        1.  Generic SCSI-1 / SCSI-2 tape drive
        2.  EXABYTE 8mm tape drive (8200 or 8500)
        3.  IBM rebadged EXABYTE 8mm tape drive (8200)
        4.  DAT drive (Compressing and non-Compressing)
        5.  QIC Cartridge tape drive

Please choose one of the above, press <Return>;
for default,or enter q to return to main menu: 1

Tape Driver Successfully Configured
  
Default special devices have been created with the following links:
        /dev/xct0       linked to  /dev/xStp0
        /dev/rct0       linked to  /dev/rStp0    and /dev/rmt/0b
        /dev/nrct0      linked to  /dev/nrStp0   and /dev/rmt/0bn

In /etc/default/boot:
No current boot string.

Enter new string, "rm" to remove string,
or enter q to leave current string as is: q

SCSI or Enhanced IDE Tape Drive Configuration Program

        1. Install a SCSI Tape Drive
        2. Install an Enhanced IDE Tape Drive
        3. Remove a SCSI Tape Drive
        4. Remove an Enhanced IDE Tape Drive
        5. Change default Tape Drive
        6. View Current SCSI and Enhanced IDE Tape Drive configuration

        Select an option or enter q to return to main menu: 6


The current tape configuration is:

     Unit       Description

       0         Generic SCSI-1 / SCSI-2 tape drive
                                               * Config Tape device successfully
Press <Return>; to continue

                                                       * You must relink kernel then reboot system
You must create a new kernel to effect the driver change you specified.
Do you wish to create a new kernel now? (y/n) y

        The UNIX Operating System will now be rebuilt.
        This will take a few minutes.  Please wait.
  
        The UNIX Kernel has been rebuilt.


Do you want this kernel to boot by default? (y/n) y

Backing up unix to unix.old
Installing new unix on the boot file system

The kernel environment includes device node files and /etc/inittab.
The new kernel may require changes to /etc/inittab or device nodes.


Do you want the kernel environment rebuilt? (y/n) y

The kernel has been successfully linked and installed.
        To activate it, reboot your system.

Setting up new kernel environment

You have successfully re-linked a new kernel.
In order for the changes to be reflected on your emergency boot floppy set,
it is recommended that you run the command '/etc/mkdev fd' and re-create
the emergency boot floppy set with the newly linked kernel.



All over  !!~~ ~~~

*為註釋

酸辣粉

这要看你磁带机接在哪个通道上。如果是主板上的SCSI第一接口，就用AD160，磁带机的ID号是为3其它的是为0。第二通道上磁带机的ID号仍是为3但“Which 'ad160' SCSI host adapter supports this device?
Select 0-1, or enter q to quit: ”这里要输1。如果服务器是加了ARRAY卡，你的磁带机又接到到了ARRAY卡上就另当别论了。你在可以这里“Enter the prefix of the SCSI host adapter that supports this device
or press <Return>; for the default: 'ad160' ”输入h查看有没有AD160这个驱动。没有可用EFS这个包的前三张盘加上。

irontech

机器配置如下:
服务器:HP ML370G3
操作系统:sco openserver5.0.7
磁带机:HP DAT24e

For ML370G3, with HP Dat 24E, your configuration should connect to LSI Logic controller.

SCO 507 doesn't support  lsil SCSI, you need to add in from HP EFS diskettle no 4. (use installpkg , select " lsil "

Before this, you need to remove your previous wrong tape configuration.

Relink kernel, reboot server.

Perform mkdev tape again, under
[Enter the prefix of the SCSI host adapter that supports this device] , manual KEY IN lsil .

Under the BUS, select 0 if you connect to the lower connector (back of the SCSI PCI card), select 1 if you connect to the upper connector

ID, refer to your HP DAT 24E, by default it should be ID 3

LUN, 0

Update SCSI, press enter 3 times, select DAT, q (quit) , rebuild kernel, reboot server.