SUBSEP变量的用法。求指教。

力哥丶

SUBSEP 数组中多个下标的分隔符,默认为"\034"


不清楚如何用。大家帮我取个例子吧。另外\034 是什么符号？

waker

PAGER='less -iRsp034' man ascii

力哥丶

回复 2# waker


    不是很明白。

jason680

回复 1# 力哥丶

Here you are

http://www.gnu.org/software/gawk ... lti_002ddimensional

8.5 Multidimensional Arrays

    Multi-scanning: Scanning multidimensional arrays.

A multidimensional array is an array in which an element is identified by a sequence of indices instead of a single index. For example, a two-dimensional array requires two indices. The usual way (in most languages, including awk) to refer to an element of a two-dimensional array named grid is with grid[x,y].

Multidimensional arrays are supported in awk through concatenation of indices into one string. awk converts the indices into strings (see Conversion) and concatenates them together, with a separator between them. This creates a single string that describes the values of the separate indices. The combined string is used as a single index into an ordinary, one-dimensional array. The separator used is the value of the built-in variable SUBSEP.

For example, suppose we evaluate the expression ‘foo[5,12] = "value"’ when the value of SUBSEP is "@". The numbers 5 and 12 are converted to strings and concatenated with an ‘@’ between them, yielding "5@12"; thus, the array element foo["5@12"] is set to "value".

Once the element's value is stored, awk has no record of whether it was stored with a single index or a sequence of indices. The two expressions ‘foo[5,12]’ and ‘foo[5 SUBSEP 12]’ are always equivalent.

The default value of SUBSEP is the string "\034", which contains a nonprinting character that is unlikely to appear in an awk program or in most input data. The usefulness of choosing an unlikely character comes from the fact that index values that contain a string matching SUBSEP can lead to combined strings that are ambiguous. Suppose that SUBSEP is "@"; then ‘foo["a@b", "c"]’ and ‘foo["a", "b@c"]’ are indistinguishable because both are actually stored as ‘foo["a@b@c"]’.

To test whether a particular index sequence exists in a multidimensional array, use the same operator (in) that is used for single dimensional arrays. Write the whole sequence of indices in parentheses, separated by commas, as the left operand:

     (subscript1, subscript2, ...) in array

The following example treats its input as a two-dimensional array of fields; it rotates this array 90 degrees clockwise and prints the result. It assumes that all lines have the same number of elements:

     {
          if (max_nf < NF)
               max_nf = NF
          max_nr = NR
          for (x = 1; x <= NF; x++)
               vector[x, NR] = $x
     }
     
     END {
          for (x = 1; x <= max_nf; x++) {
               for (y = max_nr; y >= 1; --y)
                    printf("%s ", vector[x, y])
               printf("\n")
          }
     }

When given the input:

     1 2 3 4 5 6
     2 3 4 5 6 1
     3 4 5 6 1 2
     4 5 6 1 2 3

the program produces the following output:

     4 3 2 1
     5 4 3 2
     6 5 4 3
     1 6 5 4
     2 1 6 5
     3 2 1 6

   

waker

力哥丶 发表于 2012-12-19 10:06
回复 2# waker

我能想到的让你明白的方法就是每天早上起床后读一遍新手导航,坚持半年一定有效