blade2000机器总是死机，请各位帮我诊断诊断

qdwangchao

@(#)OBP 4.5.16 2002/05/01 19:28
BBC AID Register 0000.0000.0000.0000
Power-On Reset
Executing Power On SelfTest

0>@(#) Excalibur POST 4.5.16   2002/05/01 22:34
       /dat/fw/work/staff/firmware_re/post/post-build-4.5.16_020501/excal/integrated  (firmware_re)  
0>Jump from OBP->POST.
0>CPUs present in system: 0 1
0>diag-switch? configuration variable set TRUE.
0>Diag level set to MAX.
0>MFG scrpt mode set to NONE
0>I/O port set to serial TTYA.
0>Done with First Init, reset system.
0>Current CPU frequency is 400 MHz.
0>      Resetting to 1015
0>Clock Synth Reset.
0>
0>Start selftest...
0>Init CPU
0>      Cheetah_plus Version 2.3
0>DMMU Registers Access
0>DMMU TLB DATA RAM Access
0>DMMU TLB TAGS Access
0>IMMU Registers Access
0>IMMU TLB DATA RAM Access
0>IMMU TLB TAGS Access
0>Probe Ecache
0>      Size = 00000000.00800000...
0>Ecache Data Bitwalk
0>Ecache Address Bitwalk
0>Scrub and Setup Ecache
0>Setup and Enable DMMU
0>Setup DMMU Miss Handler
0>Test and Init Temp Mailbox
1>Init CPU
1>      Cheetah_plus Version 2.3
1>DMMU Registers Access
1>DMMU TLB DATA RAM Access
1>DMMU TLB TAGS Access
1>IMMU Registers Access
1>IMMU TLB DATA RAM Access
1>IMMU TLB TAGS Access
1>Probe Ecache
1>      Size = 00000000.00800000...
1>Ecache Data Bitwalk
1>Ecache Address Bitwalk
1>Scrub and Setup Ecache
1>Setup and Enable DMMU
1>Setup DMMU Miss Handler
1>Test and Init Temp Mailbox
0>Initializing Scan Database
0>BCC:          1483203b
0>SCSI:         15060045
0>ICHIP:        0d1e203b
0>RIO:          13e5d03b
0>SCHIZO:       107be06d
0>CPMS0:        1142903b
0>CPMS1:        1142903b
0>CPMS2:        1142903b
0>CPMS3:        1142903b
0>CPMS4:        1142903b
0>CPMS5:        1142903b
0>Init I2C
0>Unquiesce Safari
0>Blast Fans
0>Set Trip Temp CPU 0 to 110C
0>Set Trip Temp CPU 1 to 110C
0>WED DEC  7 0:08:22 GMT 5
0>Safari check
0>Probe and Setup Memory
0>INFO: 1024MB Bank 0
0>INFO: No memory detected in Bank 1
0>INFO: 1024MB Bank 2
0>INFO: No memory detected in Bank 3
0>
0>Data Bitwalk on Master
0>      Test Bank 0.
0>      Test Bank 2.
0>Address Bitwalk on Master
0>INFO: Addr walk mem test on CPU 0 Bank 0: 00000000.00000000 to 00000000.40000000.
0>INFO: Addr walk mem test on CPU 0 Bank 2: 00000002.00000000 to 00000002.40000000.
0>Set Mailbox
0>Setup Final DMMU Entries
0>Post Image Region Scrub
0>Run POST from Memory
0>Verifying checksum on copied image.
0>The Memory's CHECKSUM value is 99d6.
0>The Memory's Content Size value is 9dd19.
0>Success...  Checksum on Memory Validated.
1>Probe and Setup Memory
1>INFO: No memory on cpu 1
1>Set Mailbox
1>Data Bitwalk on mem
1>      Test Bank 0.
1>      Test Bank 2.
1>Setup Final DMMU Entries
1>Map Slave POST to master memory
1>8k DMMU TLB 0 Data
0>8k DMMU TLB 0 Data
1>8k DMMU TLB 1 Data
0>8k DMMU TLB 1 Data
1>8k DMMU TLB 0 Tags
0>8k DMMU TLB 0 Tags
1>8k DMMU TLB 1 Tags
0>8k DMMU TLB 1 Tags
1>8k IMMU TLB Data
0>8k IMMU TLB Data
1>8k IMMU TLB Tags
0>8k IMMU TLB Tags
1>Instruction Cache Tag RAM
0>Instruction Cache Tag RAM
1>Instruction Cache RAM
0>Instruction Cache RAM
1>Instruction Cache Snoop Tag Field
0>Instruction Cache Snoop Tag Field
1>Flush D/W caches
0>Flush D/W caches
1>Data Cache RAM
0>Data Cache RAM
1>Data Micro Tags
0>Data Micro Tags
1>Data Cache Tags
0>Data Cache Tags
1>WCache RAM
0>WCache RAM
1>WCache Tags
0>WCache Tags
1>Prefetch Cache RAM
0>Prefetch Cache RAM
1>Prefetch Cache Tags
0>Prefetch Cache Tags
1>Print Mem Config
1>Caches : Icache is ON, Dcache is ON, Wcache is ON, Pcache is ON.
0>Print Mem Config
0>Caches : Icache is ON, Dcache is ON, Wcache is ON, Pcache is ON.
0>Memory in non-interleave config:
0>      Bank 0 1024MB : 00000000.00000000 -> 00000000.40000000.
0>      Bank 2 1024MB : 00000002.00000000 -> 00000002.40000000.
0>Scrub Memory
0>Quick Block Mem Test
0>Quick Test 16777216 bytes at 00000000.00600000
0>40% Done...
1>Flush Caches
0>Flush Caches
0>Schizo unit 0 init      test   
0>Schizo unit 0 reg       test   
0>Schizo unit 0 mem       test   
0>Schizo unit 0 PCI DMA A test   
0>Schizo unit 0 PCI DMA B test   
0>Schizo unit 0 PCI merg  test   
0>Schizo unit 0 PCI iommu test   
0>Schizo unit 0 PCI stc   test   
0>Schizo unit 0 interrupt test   
1>Schizo unit 0 init      test   
1>Schizo unit 0 reg       test   
1>Schizo unit 0 mem       test   
1>Schizo unit 0 PCI DMA   test   
1>Schizo unit 0 PCI merg  test   
1>Schizo unit 0 PCI iommu test   
1>Schizo unit 0 PCI stc   test   
1>Schizo unit 0 interrupt test   
1>Calculating memory test time
0>Calculating memory test time
1>INFO: The expected TIMEOUT for the block memory tests can exceed 2 minutes.
0>INFO: The expected TIMEOUT for the block memory tests can exceed 2 minutes.
1>INFO: The expected TIMEOUT for the MOVI memory tests can exceed 112 minutes.
0>INFO: The expected TIMEOUT for the MOVI memory tests can exceed 112 minutes.
0>Block Memory
0>Test 1067450368 bytes on bank 0....
0>0% Done...
0>2% Done...
0>3% Done...
0>4% Done...
0>6% Done...
0>7% Done...
0>9% Done...
0>10% Done...
0>11% Done...
0>13% Done...
0>14% Done...
0>16% Done...
0>17% Done...
0>18% Done...
0>20% Done...
0>21% Done...
0>22% Done...
0>24% Done...
0>25% Done...
0>27% Done...
0>28% Done...
0>29% Done...
0>31% Done...
0>32% Done...
0>34% Done...
0>35% Done...
0>36% Done...
0>38% Done...
0>39% Done...
0>41% Done...
0>42% Done...
0>43% Done...
0>45% Done...
0>46% Done...
0>48% Done...
0>49% Done...
0>50% Done...
0>52% Done...
0>53% Done...
0>55% Done...
0>56% Done...
0>57% Done...
0>59% Done...
0>60% Done...
0>62% Done...
0>63% Done...
0>64% Done...
0>66% Done...
0>67% Done...
0>69% Done...
0>70% Done...
0>71% Done...
0>73% Done...
0>74% Done...
0>76% Done...
0>77% Done...
0>78% Done...
0>80% Done...
0>81% Done...
0>83% Done...
0>84% Done...
0>85% Done...
0>87% Done...
0>88% Done...
0>90% Done...
0>91% Done...
0>92% Done...
0>94% Done...
0>95% Done...
0>97% Done...
0>98% Done...
0>99% Done...
0>Test 1073741824 bytes on bank 2....
0>0% Done...
0>2% Done...
0>3% Done...
0>4% Done...
0>6% Done...
0>7% Done...
0>9% Done...
0>10% Done...
0>11% Done...
0>13% Done...
0>14% Done...
0>15% Done...
0>17% Done...
0>18% Done...
0>20% Done...
0>21% Done...
0>22% Done...
0>24% Done...
0>25% Done...
0>27% Done...
0>28% Done...
0>29% Done...
0>31% Done...
0>32% Done...
0>34% Done...
0>35% Done...
0>36% Done...
0>38% Done...
0>39% Done...
0>40% Done...
0>42% Done...
0>43% Done...
0>45% Done...
0>46% Done...
0>47% Done...
0>49% Done...
0>50% Done...
0>52% Done...
0>53% Done...
0>54% Done...
0>56% Done...
0>57% Done...
0>59% Done...
0>60% Done...
0>61% Done...
0>63% Done...
0>64% Done...
0>65% Done...
0>67% Done...
0>68% Done...
0>70% Done...
0>71% Done...
0>72% Done...
0>74% Done...
0>75% Done...
0>77% Done...
0>78% Done...
0>79% Done...
0>81% Done...
0>82% Done...
0>84% Done...
0>85% Done...
0>86% Done...
0>88% Done...
0>89% Done...
0>90% Done...
0>92% Done...
0>93% Done...
0>95% Done...
0>96% Done...
0>97% Done...
0>99% Done...


-

qdwangchao

0>
0>Turn Schizo 0 errors on
0>Turn error traps on
0>INFO:
0>      POST Passed all devices.
0>POST: Return to OBP.
1>Return to OBP, PASS
0>Return to OBP, PASS

@(#)OBP 4.5.16 2002/05/01 19:28
BBC AID Register 0000.0000.0000.0000
POST Results: Cpu 0
  %o0  0000.0000.0000.0000
  %o1  0000.0000.0000.0000
  %o2  0000.0000.0000.0000
POST Results: Cpu 1
  %o0  0000.0000.0000.0000
  %o1  0000.0000.0000.0000
  %o2  0000.0000.0000.0000
CPU seeprom format: 0000.0000.0000.0002
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.0010.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Copy Done
PC = 0000.07ff.f000.4aa4
PC = 0000.0000.0000.4b18
Decompressing Done
Size = 0000.0000.0006.d250
ttya initialized
Start Reason: Initialize Machine
Configuring the machine:
?
  @(#)OBP 4.5.16 2002/05/01 19:28
BBC AID Register 0000.0000.0000.0000
Loading Configuration
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.8000.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Block Scrubbing Done
Copy Done
PC = 0000.07ff.f000.4aa4
PC = 0000.0000.0000.4b18
Decompressing Done
Size = 0000.0000.0006.d250
ttya initialized
Start Reason: First start after Power On
System Reset: (SPOR) (PLL)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1015 MHz @ 7:1, 8 MB)
   memory-controller
Probing gptwo at 1,0 SUNW,UltraSPARC-III+ (1015 MHz @ 7:1, 8 MB)
   memory-controller
Probing gptwo at 8,0 pci pci upa ppm
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom bbc ppm i2c dimm-fru dimm-fru
   dimm-fru dimm-fru nvram idprom i2c cpu-fru temperature cpu-fru
   temperature fan-control card-reader motherboard-fru i2c-bridge beep
   audio rtc gpio pmc floppy parallel serial
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C
CPU 1 set ambient power off temperature to 70 degrees C
CPU 1 set junction power off temperature to 110 degrees C
Memory Configuration:
Segment @ Base:        0  Size:  2048 MB ( 2-Way)
Probing /upa@8,480000 Device 0,0 Nothing there
Probing /upa@8,480000 Device 1,0 Nothing there
Probing /pci@8,600000 Device 4  SUNW,qlc fp disk
Probing /pci@8,600000 Device 1  Nothing there
Probing /pci@8,700000 Device 5  network firewire usb
Probing /pci@8,700000 Device 6  scsi disk tape scsi disk tape
Probing /pci@8,700000 Device 1  SUNW,m64B
Probing /pci@8,700000 Device 2  Nothing there
Probing /pci@8,700000 Device 3  Nothing there
Probing /pci@8,700000 Device 4  Nothing there

Start Reason: First start after Power On
System Reset: (SPOR) (PLL)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1015 MHz @ 7:1, 8 MB)
   memory-controller
Probing gptwo at 1,0 SUNW,UltraSPARC-III+ (1015 MHz @ 7:1, 8 MB)
   memory-controller
Probing gptwo at 8,0 pci pci upa ppm
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom bbc ppm i2c dimm-fru dimm-fru
   dimm-fru dimm-fru nvram idprom i2c cpu-fru temperature cpu-fru
   temperature fan-control card-reader motherboard-fru i2c-bridge beep
   audio rtc gpio pmc floppy parallel serial
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C
CPU 1 set ambient power off temperature to 70 degrees C
CPU 1 set junction power off temperature to 110 degrees C
Memory Configuration:
Segment @ Base:        0  Size:  2048 MB ( 2-Way)
Probing /upa@8,480000 Device 0,0 Nothing there
Probing /upa@8,480000 Device 1,0 Nothing there
Probing /pci@8,600000 Device 4  SUNW,qlc fp disk
Probing /pci@8,600000 Device 1  Nothing there
Probing /pci@8,700000 Device 5  network firewire usb
Probing /pci@8,700000 Device 6  scsi disk tape scsi disk tape
Probing /pci@8,700000 Device 1  SUNW,m64B
Probing /pci@8,700000 Device 2  Nothing there
Probing /pci@8,700000 Device 3  Nothing there
Probing /pci@8,700000 Device 4  Nothing there


SUNW,Sun-Blade-1000 (2 X UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.5, 2048 MB memory installed, Serial #52712054.
Ethernet address 0:3:ba:24:52:76, Host ID: 83245276.



                                                                     
Resetting ...


@(#)OBP 4.5.16 2002/05/01 19:28
BBC AID Register 0000.0000.0000.0000
Reset: 0000.0000.0000.0010 SPOR
Loading Configuration
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.8000.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Block Scrubbing Done
Copy Done
PC = 0000.07ff.f000.4aa4
PC = 0000.0000.0000.4b18
Decompressing Done
Size = 0000.0000.0006.d250
ttya initialized
Start Reason: Soft Reset
System Reset: (SPOR)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1015 MHz @ 7:1, 8 MB)
   memory-controller
Probing gptwo at 1,0 SUNW,UltraSPARC-III+ (1015 MHz @ 7:1, 8 MB)
   memory-controller
Probing gptwo at 8,0 pci pci upa ppm
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom bbc ppm i2c dimm-fru dimm-fru
   dimm-fru dimm-fru nvram idprom i2c cpu-fru temperature cpu-fru
   temperature fan-control card-reader motherboard-fru i2c-bridge beep
   audio rtc gpio pmc floppy parallel serial
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C
CPU 1 set ambient power off temperature to 70 degrees C
CPU 1 set junction power off temperature to 110 degrees C
Memory Configuration:
Segment @ Base:        0  Size:  2048 MB ( 2-Way)
Probing /upa@8,480000 Device 0,0 Nothing there
Probing /upa@8,480000 Device 1,0 Nothing there
Probing /pci@8,600000 Device 4  SUNW,qlc fp disk
Probing /pci@8,600000 Device 1  Nothing there
Probing /pci@8,700000 Device 5  network firewire usb
Probing /pci@8,700000 Device 6  scsi disk tape scsi disk tape
Probing /pci@8,700000 Device 1  SUNW,m64B
Probing /pci@8,700000 Device 2  Nothing there
Probing /pci@8,700000 Device 3  Nothing there
Probing /pci@8,700000 Device 4  Nothing there

Start Reason: Soft Reset
System Reset: (SPOR)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1015 MHz @ 7:1, 8 MB)
   memory-controller
Probing gptwo at 1,0 SUNW,UltraSPARC-III+ (1015 MHz @ 7:1, 8 MB)
   memory-controller
Probing gptwo at 8,0 pci pci upa ppm
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom bbc ppm i2c dimm-fru dimm-fru
   dimm-fru dimm-fru nvram idprom i2c cpu-fru temperature cpu-fru
   temperature fan-control card-reader motherboard-fru i2c-bridge beep
   audio rtc gpio pmc floppy parallel serial
CPU 0 set ambient power off temperature to 70 degrees C
CPU 0 set junction power off temperature to 110 degrees C
CPU 1 set ambient power off temperature to 70 degrees C
CPU 1 set junction power off temperature to 110 degrees C
Memory Configuration:
Segment @ Base:        0  Size:  2048 MB ( 2-Way)
Probing /upa@8,480000 Device 0,0 Nothing there
Probing /upa@8,480000 Device 1,0 Nothing there
Probing /pci@8,600000 Device 4  SUNW,qlc fp disk
Probing /pci@8,600000 Device 1  Nothing there
Probing /pci@8,700000 Device 5  network firewire usb
Probing /pci@8,700000 Device 6  scsi disk tape scsi disk tape
Probing /pci@8,700000 Device 1  SUNW,m64B
Probing /pci@8,700000 Device 2  Nothing there
Probing /pci@8,700000 Device 3  Nothing there
Probing /pci@8,700000 Device 4  Nothing there

fujitsu_solaris

我碰到过B2000上电源管理的问题会总死机，我把电源管理关掉了。就好了。不知道对你是否有帮助

qdwangchao

请问怎样关掉电源管理?我是新手,谢谢

风之幻想

修改/etc/power.conf.对了,你机器的messages信息有什么呢?大约多长时间会宕机呢.

qdwangchao

messages里面我看了没有关于为什么死机的消息啊,怎么修改power.conf啊?能说具体一些么?谢谢

风之幻想

在/etc/power.conf中把自动关机的那个屏蔽就可以了.先看一下是不是这个问题引起的.

qdwangchao

我修改了power.conf ,可是还是死机,是不是CPU温度太高了?请高手指点,以下是我用prtdiag -v 查看的信息:
# ./prtdiag -v
System Configuration: Sun Microsystems  sun4u SUNW,Sun-Blade-1000 (2 X UltraSPARC-III+)
System clock frequency: 145 MHZ
Memory size: 2GB        

==================================== CPUs ====================================
               E$          CPU     CPU       Temperature
CPU  Freq      Size        Impl.   Mask     Die    Ambient
---  --------  ----------  ------  ----  --------  --------
0   1015 MHz  8MB         US-III+   2.3     65 C     22 C
1   1015 MHz  8MB         US-III+   2.3     71 C     22 C

================================= IO Devices =================================
     Bus   Freq
Brd  Type  MHz   Slot        Name                              Model
---  ----  ----  ----------  --------------------------------  ----------------------
0   pci    33            1  SUNW,m64B (display)               SUNW,370-4362         
0   pci    66            4  SUNW,qlc-pci1077,2200.5 (scsi-fc+                       
0   pci    33            5  ebus/parallel-ns87317-ecpp (para+                       
0   pci    33            5  ebus/serial-sab82532 (serial)                           
0   pci    33            5  network-pci108e,1101.1 (network)  SUNW,pci-eri         
0   pci    33            5  firewire-pci108e,1102.1001 (fire+                       
0   pci    33            6  scsi-pci1000,f.37 (scsi-2)                              
0   pci    33            6  scsi-pci1000,f.37 (scsi-2)                              

============================ Memory Configuration ============================
Segment Table:
-----------------------------------------------------------------------
Base Address       Size       Interleave Factor  Contains
-----------------------------------------------------------------------
0x0                2GB               2           BankIDs 0,2

Bank Table:
-----------------------------------------------------------
           Physical Location
ID       ControllerID  GroupID   Size       Interleave Way
-----------------------------------------------------------
0        0             0         1GB             0
2        0             0         1GB             1

Memory Module Groups:
--------------------------------------------------
ControllerID   GroupID  Labels
--------------------------------------------------
0              0        J0100,J0202,J0304,J0406

=============================== usb Devices ===============================

Name          Port#
------------  -----
keyboard        1

============================ Environmental Status ============================
Fan Speeds:
----------------------------
Fan Device            Speed
----------------------------
system                  19%
cpu                     31%
power-supply           100%

================================ HW Revisions ================================
ASIC Revisions:
---------------
pci: Rev 5
pci: Rev 5
ebus: Rev 1

System PROM revisions:
----------------------
OBP 4.5.16 2002/05/01 19:28
POST 4.5.16 2002/05/01
另外请问Die    Ambient 分别是指什么温度?谢谢

风之幻想

看一下你电源的风扇是不是有问题了.

dcqzy

b2000必须打最新的补丁