#show int serial 0 Serial 0 is down,line protocol is down 能不能判断出是端口物理故障还是线路故障?
line protocol,是不是可以解释为物理协议?? 就算地址段不同,只要端口有信号,就UP.(这个是我做实验时得到的.) 那么这个line protocol down or up,到底是应该怎么解释??
前天晚间网络开始不通了,登到路由器上看,发现有个端口协议down了。但我这儿没做任何改动,问了下对端也说没有任何改动,而且对端说他们那边接口和协议都是up的。现在从我这儿ping对端都不通,不知道问题可能出在哪儿了,求各位高人帮忙看看。谢了。 hostname#show int fastethernet 0/0 fastethernet0/0 is up, line protocol is down Hardware is Gt96k FE, address is 0013.19e9.9150 (bia 0013.19e9.9150) Internet add...
在使用的路由器,接了一根专线在serial口,总是serial is up,line protocol is down的状态,reload一下就好一阵子,不知道什么原因,用sh interf看到没什么错误,就是reset interf那里有数据,请问各位是什么问题啊?是路由器的端口坏了吗?谢谢指导。下面是路由器一直在终端上显示的错误信息: *Mar 1 16:34:20.487: %DSX1-3-M32_AR_TIMEOUT: Munich 32 action request timeout: Ctrl = 0x3E030003, Channel = 0 -Process= "Seri...
有一个路由器,使用Multichannel E1的接口(8口),现在发现一个怪问题,但使用一段时间后,整个板子上的接口均会变成serial interface up,line protocol down的状态,同时网络也中断了,可以保证对端和本端的配置均未改变过,且以前可以正常通信。这时候从DDF架上做环路无法看到looped,端口状态没有任何改变。软件环路diag模式可以看到端口和协议均马上就up起来,但去掉环路后,又恢复到故障状态。查找资料后,将serial端口中的k...
cisco 2610 jl2206#show protocol Global values: Internet protocol routing is enabled Ethernet0/0 is up, line protocol is up Internet address is 26.97.32.126/24 Serial1/0 is up, line protocol is down Serial1/0.1 is up, line protocol is down Internet address is 10.48.73.49/24 Serial1/1 is up, line protocol is up Internet address is 10.48.60.1/24 Serial1/2 is up, line protocol is up Interne...
Router#show int s1/0 Serial1/0 is up, line protocol is down Mode=Sync DTE DTR=UP,DSR=UP,RTS=UP,CTS=UP,DCD=UP Interface address is xxx.xxx.xxx.xxx/30 MTU 1500 bytes, BW 64 kbit, DLY 2000 usec Encapsulation PPP, loopback not set Keepalive set(10 sec) LCP Starting configuration exchange IPCP Listening -- waiting for remote host to attempt open local IP address: 0.0.0.0 remote ...
我是刚上路的菜鸟,近来找了boson netsim的路由器模拟软件,总算一睹了router的方容,以前就纸上谈兵地学习过一点,很抽象的。 :oops: 现在我欲对RA。RB的两个物理相连的s0口作ip配置,是其能互通,发现无论是采用classless ip还是class ip,启用no shut 命令后,总会过几秒钟先提示:提示s0 change state to up 后过几秒就提示:s0 is down, line protocol is down 。我只知道那是物理端口出错的提示,但是这是模拟器呀,用那解释...
我们公司的一个分公司通过光纤连接到总部的一台cisco路由器上,目前经常出现连不上网的情况,查看路由器端口信息,发现总是:line protocol down。请问这是什么原因?如何解决?谢谢!!